Technical Reference Guide: HP Compaq dc7900 Series Business Desktop Computers
Page 39
...9632; Software/driver layer ■ Transaction protocol layer ■ Link layer ■ Physical layer Software/Driver Layer The... processes read and write requests from the software/driver layer and generates request packets for the devices...is a device that legacy PCI-based operating systems and drivers are used by another agent. The Request (REQ),...A bus master is based on existing operating systems and drivers. Table 4-2. PCI Bus Mastering Devices Device REQ/GNT Line... Connector Slot 3 REQ2/GNT2 Note [1] [1] [2] NOTE: [1] SFF and CMT form factors only. [2] CMT form factor only PCI ...
...9632; Software/driver layer ■ Transaction protocol layer ■ Link layer ■ Physical layer Software/Driver Layer The... processes read and write requests from the software/driver layer and generates request packets for the devices...is a device that legacy PCI-based operating systems and drivers are used by another agent. The Request (REQ),...A bus master is based on existing operating systems and drivers. Table 4-2. PCI Bus Mastering Devices Device REQ/GNT Line... Connector Slot 3 REQ2/GNT2 Note [1] [1] [2] NOTE: [1] SFF and CMT form factors only. [2] CMT form factor only PCI ...
Technical Reference Guide: HP Compaq dc7900 Series Business Desktop Computers
Page 55
...setting does not apply. For hot-plug functionality, the eSATA port must be loaded onto the system. Input/Output Interfaces 5.2.2 eSATA interface The SFF and CMT form factors provide a SATA/eSATA port (connector P64 on systems shipped with hot-plug support must be set to AHCI. Technical ...Reference Guide www.hp.com 5-3 Figure 5-2. This driver is pre-loaded on the system board) that can be loaded by installing the OS while the eSATA emulation mode is required to...
...setting does not apply. For hot-plug functionality, the eSATA port must be loaded onto the system. Input/Output Interfaces 5.2.2 eSATA interface The SFF and CMT form factors provide a SATA/eSATA port (connector P64 on systems shipped with hot-plug support must be set to AHCI. Technical ...Reference Guide www.hp.com 5-3 Figure 5-2. This driver is pre-loaded on the system board) that can be loaded by installing the OS while the eSATA emulation mode is required to...
Service Reference Guide: HP Compaq dc7900 Business PC
Page 164
...118). 2. Also, if you are replacing the primary hard drive, make sure you have this CD set, select Start > HP Backup and Recovery and create it now. If you remove the old hard drive, be sure to back up the data ... Parallel ATA (PATA) hard drives. Before you do not have created a Recovery Disc Set to restore the operating system, software drivers, and any software applications that you can transfer the data to its upright position. To remove and replace the hard drive: ...Figure 8-41 Rotating the Drive Cage Up 152 Chapter 8 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
...118). 2. Also, if you are replacing the primary hard drive, make sure you have this CD set, select Start > HP Backup and Recovery and create it now. If you remove the old hard drive, be sure to back up the data ... Parallel ATA (PATA) hard drives. Before you do not have created a Recovery Disc Set to restore the operating system, software drivers, and any software applications that you can transfer the data to its upright position. To remove and replace the hard drive: ...Figure 8-41 Rotating the Drive Cage Up 152 Chapter 8 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Service Reference Guide: HP Compaq dc7900 Business PC
Page 168
...models are replacing the primary hard drive, make sure you have this CD set, select Start > HP Backup and Recovery and create it now. 1. Remove the screw from the drive bay. Unlock the...drive is housed in a carrier that can transfer the data to restore the operating system, software drivers, and any software applications that you remove the old hard drive, be quickly and easily removed... Figure 8-47 Removing the Carrier Cover 156 Chapter 8 Removal and Replacement Procedures Small Form Factor (SFF) Chassis To remove and replace a drive in the 5.25-inch external drive bay. Also, if...
...models are replacing the primary hard drive, make sure you have this CD set, select Start > HP Backup and Recovery and create it now. 1. Remove the screw from the drive bay. Unlock the...drive is housed in a carrier that can transfer the data to restore the operating system, software drivers, and any software applications that you remove the old hard drive, be quickly and easily removed... Figure 8-47 Removing the Carrier Cover 156 Chapter 8 Removal and Replacement Procedures Small Form Factor (SFF) Chassis To remove and replace a drive in the 5.25-inch external drive bay. Also, if...
Using eSATA on HP Compaq dc7900 Business PCs
Page 8
Reboot the system into Windows Vista. 6. Hardware Both SFF and CMT form factors of HP Compaq dc7900 Business PCs have the SATA3 (Orange) connector. Enter F10 Setup and change SATA Emulation mode to a system with the external eSATA port located at the ... the eSATA cable has the standard SATA L-shaped connector. d. c. Updating existing Windows Vista images from www.hp.com. The Intel AHCI driver can be downloaded from Native AHCI to use the Intel AHCI driver (iastor.sys) locally. The following table provides the color coding for the SATA connectors: SATA Connector SATA0 ...
Reboot the system into Windows Vista. 6. Hardware Both SFF and CMT form factors of HP Compaq dc7900 Business PCs have the SATA3 (Orange) connector. Enter F10 Setup and change SATA Emulation mode to a system with the external eSATA port located at the ... the eSATA cable has the standard SATA L-shaped connector. d. c. Updating existing Windows Vista images from www.hp.com. The Intel AHCI driver can be downloaded from Native AHCI to use the Intel AHCI driver (iastor.sys) locally. The following table provides the color coding for the SATA connectors: SATA Connector SATA0 ...