Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MAS3184NC manuals!
Problems with Fujitsu MAS3184NC?
Ask a Question
Free Fujitsu MAS3184NC manuals!
Problems with Fujitsu MAS3184NC?
Ask a Question
Popular Fujitsu MAS3184NC Manual Pages
Manual/User Guide - Page 5
...in details how collect the information for installing MAS series disk drives.
CHAPTER 2 SPECIFICATIONS
This chapter gives detailed specifications of troubleshooting the disk drives. This chapter also describes diagnostic methods for installing it into a host computer system. PREFACE
This manual describes the MAS3735NC/NP, MAS3367NC/NP and MAS3184NC/NP (hereafter, MAS series), 3.5 type fixed...
Manual/User Guide - Page 7
... setting status set at factory shipment.
2. To short the setting terminal, use the short plug attached when the device is on .
• Write protect: CN2 9-10 (NP model only...
If the error of terminals not described 5-5
in this manual are applied for their ECC. Alert message
Page
Data loss
2-5
For MAS series, Reed Solomon codes are as follows:
Task Mounting Installation
A hazardous ...
Manual/User Guide - Page 12
... pin connector type 16-bit SCSI model (NP model 4-13 Cable connector requirements 4-20 External operator panel (on NP model drives only 4-21
CHAPTER 5 INSTALLATION 5-1 5.1 Notes on Handling Drives 5-1 5.2 Connections...5-3 5.3 Setting Terminals ...5-5 5.3.1 SCSI ID setting...5-6 5.3.2 Each mode setting ...5-8 5.3.3 Mode settings ...5-10 5.4 Mounting Drives...5-11 5.4.1 Check before mounting...
Manual/User Guide - Page 13
... of troubleshooting procedures 6-13 Troubleshooting with disk drive replacement in the field 6-13 Troubleshooting at the repair site 6-15 Troubleshooting with parts replacement in the factory 6-16 Finding possibly faulty parts 6-16
CHAPTER 7 ERROR ANALYSIS 7-1 7.1 Error Analysis Information Collection 7-1 7.1.1 Sense data...7-1 7.1.2 Sense key, sense code, and subsense code 7-1 7.2 Sense...
Manual/User Guide - Page 14
...
Figure 1.1 Figure 1.2 Figure 1.3 Figure 1.4
page NC model drives outer view 1-6 NP model drives outer view 1-6 Disk/head configuration...1-7 System configuration ...1-9
Figure... ...4-4 Mounting frame structure ...4-5 Limitation of side-mounting 4-5 Surface temperature measurement points 4-6 Service clearance area ...4-7 Spin-up current waveform (+12 VDC 4-8 Power on/off sequence (1)...
Manual/User Guide - Page 32
... surface temperature is as possible as follows. Therefore, the user must design the system cabinet so that requires repair, adjustments, or replacement. The drive is designed for a MTTR of 30 minutes or less.
(3) Service life
The service life under suitable conditions and treatment is 5 years.
Note:
The "average DE surface temperature" means the average temperature...
Manual/User Guide - Page 43
Table 3.4 Format capacity
Model
Data heads Data block length
MAS3735NC/NP
8
MAS3367NC/NP
4
512
MAS3184NC/NP
2
User blocks 143,552,136 71,819,496 35,890,... of sectors in the alternate cylinders.
3.2 Logical Data Block Addressing
Independently of the physical structure of the disk drive, the IDD adopts the logical data block addressing as a data access method on the IDD (format capacity)...
Manual/User Guide - Page 50
... terminates. Remark: When a write protection is prohibited through the setting terminal, the auto alternate block allocation processing specification is successful. Alternate block allocation will be processed in the data... data block if recovery is disabled.
However, the initiator can recover the twice error by the WRITE LONG command is rewritten and verified in Cache, - the sectors...
Manual/User Guide - Page 57
... the IDD is shown in Figure 4.7.
[Surface P'] • Setting terminal (MP model only) • External operator panel connector
[Surface P] • Cable connection
[Surface R] • Hole for mounting screw
[Surface Q] • Hole for mounting screw
Figure 4.7 Service clearance area
(6) External magnetic field
The drive should not be installed near equipment.
(8) Others Seals on the DE...
Manual/User Guide - Page 73
... Notes on Handling Drives 5.2 Connections 5.3 Setting Terminals 5.4 Mounting Drives 5.5 Connecting Cables 5.6 Confirming Operations after Installation and Preparation
for Use 5.7 Dismounting Drives 5.8 Spare Disk Drive
This chapter describes the notes on handling drives, connections, setting switches and plugs, mounting drives, connecting cables, confirming drive operations after installation and...
Manual/User Guide - Page 77
... terminals and SCSI terminating resistor before installing the IDD in the system as required.
• Setting terminal: CN1 (NC model), CN2 (NP model)
Figure 5.2 shows the location of terminals not described in SCSI connector CN1.). Do not change the setting of setting terminal (NP model only. 5.3 Setting Terminals
A user sets up the following setting pins during the power is turned...
Manual/User Guide - Page 81
... on the SCSI bus.
(5) Setting the bus width of the bus width setting for the IDD SCSI interface is not supported.
C141-E185
5-9 Table 5.5 Setting of the SCSI interface (NP model)
Bus width 16 bit bus 8 bit bus *1. This setup terminal must be set to the operation mode. Set at factory shipment.
When this setup terminal is open, the...
Manual/User Guide - Page 89
...error. In this case, the number of logical data blocks after initialization is formatted with a specific (default) data format for each model (part number) when shipped from the default format, all recording surface of the cable. • Power is installed...terminals. c) Check the setting of cylinders in the format parameter (page code = 3) and drive parameter (page code = 4). However, ...
Manual/User Guide - Page 93
...
1. Determine the parameter values in normal operations.
(2) Disconnection/reconnection parameters (page code = 2)
The following parameters are used to optimize the start timing of reconnection ... recommended to use the default setting in consideration of the following parameters according to evaluate the validity of SCSI Logical Interface Specifications for further details.
•...
Manual/User Guide - Page 103
...Other error analysis information
CAUTION
Data loss Save data stored on the disk drive before requesting repair. C141-E185
6-7 Contact Fujitsu representative to submit information for the disk drive. (3) Parts that can be replaced in the field
The PCA cannot be replaced in the field.
(4) Service system and repairs
Fujitsu has the service system and repair facility for replacing or repairing the...
Fujitsu MAS3184NC Reviews
We have not received any reviews for Fujitsu yet.