Fujitsu MAG3182LC - Enterprise 18.2 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MAG3182LC manuals!
Problems with Fujitsu MAG3182LC?
Ask a Question
Free Fujitsu MAG3182LC manuals!
Problems with Fujitsu MAG3182LC?
Ask a Question
Popular Fujitsu MAG3182LC Manual Pages
Manual/User Guide - Page 4
FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damange to this product. Versions in which there functions can be used in this manual handy, and keep it carefully.
Keep this manual.
Function
Equipment Version Which Supports These Functions
Equipment EPROM Standard INQUIRY Data Product Version No. Functional Limitations...
Manual/User Guide - Page 5
... Standards Institute (ANSI)
All Right Reserved, Copyright © 1998, 1999 Fujitsu Limited
iv
C141-E064-03EN Related Standards
Specifications and functions of the Small Computer
Standards Institute
System Interface (SCSI)
(ANSI)
WORKING DRAFT Information
American National
Technology SCSI-3 Parallel Interface Standards Institute
(ANSI)
Dfaft proposed American National Standard for...
Manual/User Guide - Page 6
... need arises, use in computer systems. The MANUAL ORGANIZATION section describes organization and scope of fixed disk drives and their standard features, hardware, and system configuration. Chapter 2
SPECIFICATIONS
This chapter gives detailed specifications of model names and product numbers, and SCSI interface functions.
Chapter 5
INSTALLATION
This chapter explains how to do about...
Manual/User Guide - Page 8
DISCLAIMER
Failure of the SCSI, i.e., the interface for drive failures caused by misuse by the user, poor environmental conditions, power trouble, host problems, cable failures, or any failure not caused by the drive itself. Fujitsu is defined as a failure requiring adjustments, repairs, or replacement. However, in this manual, the typical model names (Note 2) are used unless otherwise ...
Manual/User Guide - Page 9
... is turned on . Alert message
Heat An air flow with an adequate wind velocity must collect the error information using the REQUEST SENSE command. Do not change the setting of terminals except following setting pins during servicing or repair. Damage 1. Damage Do not open the DE in the field because it is required in an...
Manual/User Guide - Page 10
...-03EN
ix Installation Requirements 5. General Description 2. Specifications 3. Diagnostics and Maintenance
1. Sense Data and error Recovery Procedure 5. Removal and Replacement Procedures 5. SCSI Bus 2. Command Specification 4. MANUAL ORGANIZATION
PRODUCT MANUAL (This manual)
SCSI Physical Interface
Specifications
SCSI Logical Interface
Specifications
Maintenance Manual
1.
Manual/User Guide - Page 34
...service mechanic to diagnose and repair a drive malfunction.
C141-E064-03EN
2 - 5 Mishandling by the operator, failures due to be accessed should be distributed over the disk medium equally.
(1) Unrecoverable error rate
Errors...MTBF)
MTBF of the IDD during initialization and replaced by the equipment are not included in the error rate. The drive is 1,000,000 hours (operating: 24 ...
Manual/User Guide - Page 64
... in Figures 4.11.
[Surface P'] • Setting terminal • External operator panel connector • Spindle sync connector
[Surface R] • Hole for mounting screw
[Surface P] • Cable connection
[Surface Q] • Hole for mounting screw
Figure 4.11 Service clearance area
(5) External magnetic field
The drive should not be installed near the ferromagnetic body like a speaker to...
Manual/User Guide - Page 84
... strictly observed.
(1) General notes a) Do not give excess pressure to the drive. C141-E064-03EN
5 - 1 Do not touch PCAs except for use, and dismounting drives.
5.1 Notes on hard material such as a rubber mat, not on Handling Drives The items listed in the specifications in Table 2.1 must be careful when unpacking. Check that the "This Side...
Manual/User Guide - Page 99
... after initialization is connected to the terminating resistor.
In this case, the number of SCSI Logical Interface Specifications for a recoverable error. b) Check the following data attributes at abnormal end
a) When sense data can change the following items for each model (part number) when shipped from the default format, all sides of the disk must be...
Manual/User Guide - Page 103
... parameters need not be set. Determine the parameter values in consideration of the following performance factors of the system:
• Time required for reconnection processing • Average data transfer rate of the SCSI bus • Average amount of processing data specified with a command
Refer to Chapter 2 of SCSI Logical Interface Specifications for how to...
Manual/User Guide - Page 111
... for replacing or repairing the disk drive. Note:
The "average DE surface temperature" means the average temperature at the DE surface throughout the year when the IDD is destroyed during servicing or repair.
6 - 6
C141-E064-03EN Generally, the following information must be included:
a) IDD model, part number (P/N), revision number, serial number (S/N), and date of manufacturing
b) Error...
Manual/User Guide - Page 127
...
MAE3182LC SCA2, LVD
MAE3091LP 68-pin, LVD 512B
9.1 GB
MAE3091LC SCA2, LVD
MAG3182LP 68-pin, LVD 512B
18.2 GB
MAG3182LC SCA2, LVD
MAG3182MP 68-pin, LVD 512B
18.2 GB
MAG3182MC SCA2, LVD
MAG3091LP 68-pin, LVD 512B
9.1 GB
MAG3091LC SCA2, LVD
MAG3091MP 68-pin, LVD 512B
9.1 GB
MAG3091MC SCA2, LVD
Ultra SCSI
Mounting screw
Part...
Manual/User Guide - Page 129
... unit 1-9 Mode setting 5-8 Mode settings 5-9 Model name 2-1, D-1, D-2 Motor start mode 5-8 Motor start mode setting 5-8 Mounting drives 5-10 Mounting frame...sync 3-8 EPR4ML 1-9 Packaging 5-2 Partial response class 4 maximum likelihood
1-9 Parts that can be replaced in the field 6-6 Physical sector allocation 3-6 Positioning error rate 2-5 Power cable 4-28 Power on/off sequence 4-13, 4-14 ...
Manual/User Guide - Page 130
... Sequential starting of spindle motor 4-15 Service clearance area 4-11 Service life 2-6, 6-5 Service system and repairs 6-6 Setting SCSI terminal 5-7 Setting SCSI terminal power supply 5-7 Setting check list 5-10 Setting parameters 5-18 Setting terminals 5-5, 5-6, B-1, B-2
Setting terminals position 5-5 Shock 2-4 Spare sector 3-5 Specifications 2-1 Specifying CDB 5-17 Spindle motor 1-9 Standard...
Fujitsu MAG3182LC Reviews
We have not received any reviews for Fujitsu yet.