Dell PowerEdge XR8610t Support and Manuals
Get Help and Manuals for this Dell item
View All Support Options Below
Free Dell PowerEdge XR8610t manuals!
Problems with Dell PowerEdge XR8610t?
Ask a Question
Free Dell PowerEdge XR8610t manuals!
Problems with Dell PowerEdge XR8610t?
Ask a Question
Popular Dell PowerEdge XR8610t Manual Pages
Installation and Service Manual - Page 1
A00 Dell PowerEdge XR8610t
Installation and Service Manual
Regulatory Model: E07B Regulatory Type: E07B001 August 2023 Rev.
Installation and Service Manual - Page 3
......19 Video specifications...20 Environmental specifications...20 Environmental considerations...21 Thermal restriction matrix...22
Chapter 4: Initial system setup and configuration 24 Setting up the system...24 iDRAC configuration...24 Options to set up iDRAC IP address...24 Options to log in to iDRAC...25 Options to download drivers and firmware ...26
Chapter 5: Resources to install operating...
Installation and Service Manual - Page 5
Installing the system board ...84 Trusted Platform Module...86
Upgrading the Trusted Platform Module...86 Initializing TPM for users...87 Initializing the TPM 2.0 for users...87
Chapter 9: Jumpers and connectors 89 System board jumpers and connectors ...89 System board jumper settings...90 Disabling a forgotten password...91
Chapter 10: Using system diagnostics 92 Dell Embedded System ...
Installation and Service Manual - Page 22
Table 17. Gaseous contamination specifications
Gaseous contamination
Specifications
Copper coupon corrosion rate
Installation and Service Manual - Page 25
... AB) cable.
Dell Lifecycle Controller User's Guide at https:// www.dell.com/idracmanuals or for system specific Integrated Dell Remote Access Controller User's Guide, go to the iDRAC dedicated network port or use the iDRAC legacy username and password -
Initial system setup and configuration
25
Then you are prompted to https://www.dell.com/poweredgemanuals > Product Support page of...
Installation and Service Manual - Page 28
..., or DVD.
28
Resources to www.dell.com/support/drivers. 2. Downloading drivers and firmware
It is recommended that you do not have the Service Tag, click Browse all drivers that you clear the web browser cache before downloading the drivers and firmware.
NOTE: If you download and install the latest BIOS, drivers, and systems management firmware on the system. Steps 1. Prerequisites...
Installation and Service Manual - Page 30
... the system security settings, such as system password, setup password, Trusted Platform Module (TPM) security, and UEFI secure boot.
Sets the redundant OS information for redundant OS control. System BIOS
To view the System BIOS screen, power on the system.
System Setup Main Menu (continued) Option Service Tag Settings
Description Enables you to the installed memory.
Specifies...
Installation and Service Manual - Page 34
...set to 0 by default. Auto maps to support older HyperV.
The feature is set to Enabled by default.
Displays the amount of enabled cores in each processor:
Description
Specifies the family, model, and stepping of -Band Management Service Module at post reset. Processor Settings details (continued) Option Dell... Action Required (SRAR) errors to one of Cores
Description...
Installation and Service Manual - Page 35
... are available when the Boot Mode is set to unexpected behavior. Table 32. This option is set to All Drives and non-Dell qualified NVMe drives are present, you to Disabled by default. The Boot Settings only support UEFI mode.
● UEFI: The Unified Extensible Firmware Interface (UEFI) is set to Enabled and the system fails to...
Installation and Service Manual - Page 36
... the following format: nqn.1988-11.com.dell:.. This option is set to change the boot device order. The first option in UEFI Boot Mode. Enables you to None by default.
NOTE: Network Settings are not supported in IQN format.
When enabled, a UEFI PXE boot option is set to control the configuration of the iSCSI...
Installation and Service Manual - Page 40
... bifurcation supports on the system. The Serial Communication option is applicable only if the serial COM port is selected as
the primary video. BIOS will output displays to Riser.
This setting can withhold snoop requests, from Paddle card to Riser and Slimline connector to both the Option ROM and UEFI drivers are installed.
If...
Installation and Service Manual - Page 86
...process to enter the service tag.
Manually update the Service Tag
After replacing a system board, if Easy Restore fails, follow this task If you know the system service tag, use the default configuration settings, press N
NOTE: After the restore process is a service technician replaceable part only. CAUTION: The TPM plug-in module breaks the
86
Installing and removing system components...
Installation and Service Manual - Page 89
... provides some basic and specific information about jumpers and switches. System board connectors
Jumpers and connectors
89 To install components and cables correctly, you must know the connectors on the various boards in the system. Topics:
• System board jumpers and connectors • System board jumper settings • Disabling a forgotten password
System board jumpers...
Installation and Service Manual - Page 95
... sales teams
Steps 1. ● Reference materials, including the Installation and Service Manual, and mechanical overview ● The system service tag to quickly access the specific hardware configuration and warranty information ● A direct link to Dell to your specific product or 2. Getting help
95 This information is used by Dell Technical Support to troubleshoot the issue.
Installation and Service Manual - Page 97
... your system
For information about setting up your system, see the Getting Started Guide document that is shipped with your system
For information about the iDRAC features, configuring and logging in the documentation resources table: ● From the Dell support site:
1. For information about updating drivers and
www.dell.com/support/drivers
firmware, see the Methods to iDRAC...
Dell PowerEdge XR8610t Reviews
We have not received any reviews for Dell yet.