Product Manual
Page 36
...add a new rule to the end of a list. When adding using the CLI add command, the default is necessary to indicate the current category. Referencing by ...the route: gw-world:/main> add Route Name=new_route1 Interface=lan Network=lannet To deselect the category, the command is done ... initial cc command before individual objects can be added to as the IP rule set have a "/" character following their names when displayed by... by a comma "," character. Subsequent manipulation of that the command prompt changes to first choose a member of such a rule 36 When specifying multiple...
...add a new rule to the end of a list. When adding using the CLI add command, the default is necessary to indicate the current category. Referencing by ...the route: gw-world:/main> add Route Name=new_route1 Interface=lan Network=lannet To deselect the category, the command is done ... initial cc command before individual objects can be added to as the IP rule set have a "/" character following their names when displayed by... by a comma "," character. Subsequent manipulation of that the command prompt changes to first choose a member of such a rule 36 When specifying multiple...
Product Manual
Page 95
...lan IP=10.1.1.2 As explained next, this interface. 2. Ethernet Interfaces Chapter 3. By default, the interface uses the maximum size supported. • High Availability There are two options which are specific to the IP address wan_ip: gw-world:/> show Address IP4Address InterfaceAddresses/wan_ip 95 Changing the IP Address of an Ethernet Interface To change the IP...that can be found in bytes that is enabled by default. • MTU This determines the maximum size of CLI commands that can be used with Ethernet interfaces can also be used by default. This is used . This ...
...lan IP=10.1.1.2 As explained next, this interface. 2. Ethernet Interfaces Chapter 3. By default, the interface uses the maximum size supported. • High Availability There are two options which are specific to the IP address wan_ip: gw-world:/> show Address IP4Address InterfaceAddresses/wan_ip 95 Changing the IP Address of an Ethernet Interface To change the IP...that can be found in bytes that is enabled by default. • MTU This determines the maximum size of CLI commands that can be used with Ethernet interfaces can also be used by default. This is used . This ...
Product Manual
Page 109
...able to achieve this setting is needed to flush the ARP Cache from within the CLI. The Size of iface lan Dynamic 10.4.0.1 = 1000:0000:4009 Dynamic 10.4.0.165 = 0002:a529:1f65 Expire... NetDefendOS to issue new ARP queries to manually force the update. This can be changed MAC address and this will remember addresses that NetDefendOS does not continuously request such addresses...replaced with the CLI command arp -flush. This can be done with new hardware and retains the same IP address then it will be necessary to discover the MAC/IP address mappings for...
...able to achieve this setting is needed to flush the ARP Cache from within the CLI. The Size of iface lan Dynamic 10.4.0.1 = 1000:0000:4009 Dynamic 10.4.0.165 = 0002:a529:1f65 Expire... NetDefendOS to issue new ARP queries to manually force the update. This can be changed MAC address and this will remember addresses that NetDefendOS does not continuously request such addresses...replaced with the CLI command arp -flush. This can be done with new hardware and retains the same IP address then it will be necessary to discover the MAC/IP address mappings for...
Product Manual
Page 149
...IP address object in the menu bar - Go to display the contents of the default main routing table. Default Static Routes are Added Automatically for Each Interface When the NetDefend...lan 0 213.124.165.0/24 wan 0 0.0.0.0/0 wan 213.124.165.1 0 Web Interface To see the active routing table in the Web Interface, select the Routes item in the Status dropdown menu in the address book and these IP objects must have their addresses changed... table Tip: The CLI cc command may be needed first In the CLI example above, it was necessary to change context) before manipulating individual routes....
...IP address object in the menu bar - Go to display the contents of the default main routing table. Default Static Routes are Added Automatically for Each Interface When the NetDefend...lan 0 213.124.165.0/24 wan 0 0.0.0.0/0 wan 213.124.165.1 0 Web Interface To see the active routing table in the Web Interface, select the Routes item in the Status dropdown menu in the address book and these IP objects must have their addresses changed... table Tip: The CLI cc command may be needed first In the CLI example above, it was necessary to change context) before manipulating individual routes....
Product Manual
Page 544
...stateful NAT pools (see NAT) Static address translation (see SAT) Static ARP Changes setting, 114 Strip DontFragment setting, 507 switch routes (see transparent mode) Sync...SNMP) setting, 69 System Name (SNMP)setting, 69 T tab completion (see CLI) TCP Auto Clamping setting, 508 TCP ECN setting, 511 TCP FIN/URG ..., 213 grouping IP addresses, 213 implementation, 208 single host routes, 209 switch routes, 207, 209 with high availability, 211 with VLANs, 210 vs routing mode...setting, 490, 495 V Validation Timeout setting, 49 virtual LAN (see VLAN) virtual private networks (see VPN) VLAN, 97 advanced settings, ...
...stateful NAT pools (see NAT) Static address translation (see SAT) Static ARP Changes setting, 114 Strip DontFragment setting, 507 switch routes (see transparent mode) Sync...SNMP) setting, 69 System Name (SNMP)setting, 69 T tab completion (see CLI) TCP Auto Clamping setting, 508 TCP ECN setting, 511 TCP FIN/URG ..., 213 grouping IP addresses, 213 implementation, 208 single host routes, 209 switch routes, 207, 209 with high availability, 211 with VLANs, 210 vs routing mode...setting, 490, 495 V Validation Timeout setting, 49 virtual LAN (see VLAN) virtual private networks (see VPN) VLAN, 97 advanced settings, ...