D-Link DES-1210-52 Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link DES-1210-52 manuals!
Problems with D-Link DES-1210-52?
Ask a Question
Free D-Link DES-1210-52 manuals!
Problems with D-Link DES-1210-52?
Ask a Question
Most Recent D-Link DES-1210-52 Questions
Des 1210-52. What Is Subtree Oid And Oid Mask Of Above Device.
(Posted by iatultiwari07 10 years ago)
Doesn't Work
When I added to our current LAN, this New Switch didn't work, and also didn't recieve IP address fro...
When I added to our current LAN, this New Switch didn't work, and also didn't recieve IP address fro...
(Posted by chanrithypol 11 years ago)
Resetting New Switch
Hello, we recently purchased this new switch and as we were configuring the new ip address and passw...
Hello, we recently purchased this new switch and as we were configuring the new ip address and passw...
(Posted by graywolf8303 12 years ago)
Popular D-Link DES-1210-52 Manual Pages
Product Manual - Page 3
Table of Contents
D-Link Web Smart Switch User Manual
Table of Contents
Table of Contents ...i About This Guide...1
Terms/Usage...1 Copyright and Trademarks ...1 Product Introduction ...2 DES-1210-08P ...3
Front Panel ...3 Rear Panel...3 DES-1210-28 ...3 Front Panel ...3 Rear Panel...4 DES-1210-28P ...4 Front Panel ...4 Rear Panel...5 DES-1210-52 ...5 Front Panel ...5 Rear Panel...6 Hardware ...
Product Manual - Page 4
...D-Link Web Smart Switch User Manual
System Settings...22 Web-based Management...23 Tool Bar > Save Menu ...24
Save Configuration ...24 Save Log ...24 Tool Bar > Tool Menu ...24 Reset ...24 Reset System ...24 Reboot Device ...25 Configuration Backup & Restore ...25 Firmware Backup and Upload ...25 Tool Bar > Smart Wizard...26 Tool Bar > Online Help...26 Function Tree ...28 Device Information...28...
Product Manual - Page 5
...-08P/28P 65 Time-Based PoE > Time Range Settings (Only for DES-1210-08P/28P 66 LLDP > LLDP Global Settings (Only for DES-1210-08P/28P 66 LLDP > LLDP Remote Port Information (Only for DES-1210-08P/28P 67 LLDP > LLDP-MED Settings (Only for DES-1210-28P 68 Command Line Interface...69 To connect a switch via TELNET:...69 Logging on to the Command Line Interface 69 CLI Commands: ...69 Download...
Product Manual - Page 8
... IP or MAC traffic. It allows extensive switch configuration setting, and basic configuration of discovered devices such as server or gateway devices.
In addition, users can utilize the SNMP MIB (Management Information Base) to factory defaults, setting the administrator password, rebooting the Switch, or upgrading the Switch firmware can also access the Switch via Telnet. D-Link Web Smart...
Product Manual - Page 9
...LED : The Power LED lights up when the Switch is running on 100M.
3
Light off indicates this port. Rear Panel
Figure 2 - When a port has amber light indicates that port is not providing the power or no PD found. 1 Product Introduction
DES-1210-08P 8-Port 10/100Mpbs PoE Web Smart Switch Front Panel
D-Link Web Smart Switch User Manual
Figure 1 - Reset: By pressing the Reset button...
Product Manual - Page 10
... Port LED, and the current setting is not providing the power or no PD found.
4 Solid amber indicates a PoE error has occurred at this port is indicated by the Mode LED under the button. Blinking indicates that port is used .
And light off indicates this port. 1 Product Introduction
D-Link Web Smart Switch User Manual
Port Link/Act/Speed LED (25F, 26F, 25T, 26T, 27, 28): The Link...
Product Manual - Page 11
... the DES-1210-52, the MiniGBIC ports are shared with 4-Port 10/100/1000Mbps and 2 Combo SFPs Front Panel
Figure 7 - 1 Product Introduction
D-Link Web Smart Switch User Manual
Port LED (25F, 26F, 25T, 26T, 27, 28): The Port LED flashes which indicates a network link through the corresponding port. When MiniGBIC port is running on 100M. Port Link/Act/Speed LED (1-48): The Link/Act/Speed...
Product Manual - Page 36
... button to the switch. 5 Configuration
D-Link Web Smart Switch User Manual
Figure 50 - Twisted pair Port Link Up/Link Down: Copper port connection information. RSTP Port State Change: Events of power per port (Only for DES-1210-08P and 28P) PoE Power Error: The four trap events are: power over loading, short circuit, thermal shutdown and power deny (Only for DES-1210-08P and 28P). PoE Power On...
Product Manual - Page 41
...the VID group, click Apply.
35
System > SNMP Settings > SNMP Trap Setting
System > Password Access Control Setting a password is selected, all levels of the system log server. The lowest level of event message will be assigned to secure the Web-Smart Switch. UDP Port: Specifies the UDP port to delete the VLAN group.
5 Configuration
D-Link Web Smart Switch User Manual
Figure 59 -
Product Manual - Page 74
...From Port / To Port and Enable / Disable and then click Apply to configure the Power PSE TLV (Type-length-value) state of LAN policies and device location discovery.
Currently, DES-1210-28P supports only the extended and automated power management of LLDP. LLDP-MED supports features such as IP phones and APs.
5 Configuration
D-Link Web Smart Switch User Manual
LLDP > LLDP-MED Settings...
Product Manual - Page 75
... prompt will appear as shown below (DES-1210-28P>):
DES-1210-28P login: admin Password:
DES-1210-28P>
Figure 115 - The default user name and password is admin. 6 Command Line Interface
D-Link Web Smart Switch User Manual
6 Command Line Interface
The D-Link Web Smart Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by the switch IP address, eg.
Product Manual - Page 78
...Device will be reset to the default settings.
Syntax show ipif
Example
DES-1210-28P> show switch command
Config account admin password The command sets the administrator password. DES-1210-28P>
Figure 121 - Syntax config account admin password
72 6 Command Line Interface
D-Link Web Smart Switch User Manual
Figure 120 - The reboot command
Reset All configurations will reboot after reset...
Product Manual - Page 81
... Bytes
Port Functions 8, 24 or 48 10/100BaseT ports comply with the following standards: - Supports Full-Duplex operations 4 1000Base-T ports of DES-1210-28/28P /52 comply with the following standards: - DEM-312GT2 (1000BASE-SX, 2km) - DES-1210-08P : 1.6Gbps - DEM-210 (100BASE-FX, 15km) - Technical Specifications
D-Link Web Smart Switch User Manual
Appendix B - DES-1210-08P: 1.19Mpps...
Product Manual - Page 82
... Auto Configuration LLDP(DES-1210-08/28P only) LLDP-MED (DES-1210-28P only) Trap setting for destination IP, system events, fiber port events, twisted-pair port events Port access control Web-based configuration backup / restoration Web-based firmware backup/restore Firmware upgrade using SmartConsole Utility & Web-based management Reset, Reboot
D-Link Web Smart Switch User Manual
76 Appendix...
Specifications - Page 1
...131;ƒConfigurable MDI/MDIX ƒƒAuto-Surveillance VLAN ƒƒLLDP1 ƒƒLLDP-MED2
Trap & Logs
ƒƒSNMP Trap ƒƒTrap for SmartConsole Utility
Online Help via Web-based Management
ƒƒLink to local support website ƒƒOnline User Guide
1 DES-1210-08P/28P only 2 DES-1210-28P only
8/28/52-Port Web Smart Switch
The DES-1210 Series is possible...
D-Link DES-1210-52 Reviews
We have not received any reviews for D-Link yet.