Cisco SGE2000P - Small Business Managed Switch Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco SGE2000P manuals!
Problems with Cisco SGE2000P?
Ask a Question
Free Cisco SGE2000P manuals!
Problems with Cisco SGE2000P?
Ask a Question
Most Recent Cisco SGE2000P Questions
How Do You Know If Your Linksys E2000 Is Working Correctly?
(Posted by mkirby64 12 years ago)
Cisco SGE2000P Videos
SYS2U.COM - Cisco SGE2000P - 24-Port 1000 Mbps Stackable L3, 4 SFP, PoE
Duration: 4:40
Total Views: 4,154
Duration: 4:40
Total Views: 4,154
Cisco SGE2000P $850 Price Reduction
Duration: :34
Total Views: 23
Duration: :34
Total Views: 23
Popular Cisco SGE2000P Manual Pages
Administration Guide - Page 6
... Network Management Protocol (SNMP) protocol. The "P" model of its clock with the Linksys One Portal - What's in this User Guide? Use the instructions in this guide to help you connect the switch, set it up, and configure it is fully manageable using the Ethernet switch. These instructions should be centrally powered by uninterruptible power supplies if necessary. Chapter
Introduction...
Administration Guide - Page 10
...its default settings. Linksys One Ready Communications Solution
2
5
Chapter 2: Getting to its speed and duplex accordingly. CAUTION: All user-defined settings are both connected, then the mini-GBIC port takes priority. By default, the stacking ports are shared with 24 auto-sensing, Ethernet (IEEE 802.3) network ports, which use RJ-45 connectors.
The Gigabit Ethernet ports support network...
Administration Guide - Page 12
... PC's HyperTerminal program. Keep the RPS port covered when not in use a Linksys RPS1000 Redundant Power Supply unit and a proper RPS cable (RPSCBL1) with serial ports. Only use . RPS Port
An optional Redundant Power Supply (RPS) is connected to Know the Switch
The Back Panel
NOTE: Many modern laptop computers are not supplied with the...
Administration Guide - Page 16
... or other end to the console port (located on the Ethernet switch. If you use the console interface to configure the Ethernet switch, then connect the supplied serial cable to your PC's serial port. (The PC must be running VT100 terminal emulation software, such as HyperTerminal.)
6. If you use the power cord that is supplied with the...
Administration Guide - Page 17
... network connections.
• By factory default, Ethernet switches boot in stacking mode.
• Stack ID can be used for directions. All stack masters are applied only to the master unit;
A stack unit can build stacks by building a new stack from 1 to a stack.
• Settings are accessed through a single IP address through a single point as regular...
Administration Guide - Page 25
...use the command-line interface ...override the system administrator's assignment and resolve the conflict. Chapter
Linksys One Ready Communications Solution
3
manually-set Unit ID number are inactive. Occasionally, due to configure .... Chapter 3: Connecting the Switch
20
Configuring Units and Ports The Stack Master then configures each unit in factory default mode (they have a unit ID...
Administration Guide - Page 38
... the application.
NOTE: The Ethernet switch is setup by default to configure the HyperTerminal application on the default VLAN 100. Linksys One Ready Communications Solution
4
33
Chapter 4: Console Configuration
Overview Configuring the HyperTerminal Application
Before you use the console interface, you will need to obtain its IP address via DHCP on your network. Select an...
Administration Guide - Page 40
...
Linksys One Ready Communications Solution
4
35
Chapter 4: Console Configuration
Connecting to the Switch using the IP address of your Ethernet switch....DHCP server or the console interface), you can connect to the switch through a Telnet session.
1. Type the user name and password.
4. Chapter
Connecting to the Switch using Telnet or SSH
If you know the IP address of your Ethernet switch...
Administration Guide - Page 46
...)
IP address of the Ethernet switch
Specifies the department name. (Range: 1 to 32 characters)
Specifies the organization name. (Range: 1 to 32 characters)
Specifies the location or city name. (Range: 1 to 32 characters)
Specifies the state or province name. (Range: 1 to configure security settings on the Ethernet switch, as well as generate and display the certificate. Linksys...
Administration Guide - Page 48
...is displayed.
Verify that the address you want to assign an static IP address to be a DHCP client, then select ENABLE. Linksys One Ready Communications Solution
4
43
Chapter 4: Console Configuration
Configuring the Switch through the Console or Telnet Interface IP Address
Subnet Mask Default Gateway Management VLAN DHCP client
The IP Address of the DHCP client is correct and does...
Administration Guide - Page 49
...IP address configuration settings:
a. b. Select Edit to the Action menu.
Select Save to save your changes are complete, press the Esc key to return to make changes. Select Edit to configure HTTPS settings.
Chapter
Linksys One Ready Communications Solution
4
To change HTTPS settings... 4: Console Configuration
44
Configuring the Switch through the Console or Telnet Interface
Administration Guide - Page 50
... the traceroute test. Linksys One Ready Communications Solution
4
Chapter
Ping
The Ping screen displays the IP address of two tests, Ping and TraceRoute. After the ping test is complete, the TraceRoute screen displays the IP address, status, and statistics of the traceroute test.
45
Chapter 4: Console Configuration
Configuring the Switch through the Console or Telnet Interface
Select...
Administration Guide - Page 51
... is being downloaded, When your changes. When you copy an image to change the settings. Chapter 4: Console Configuration
46
Configuring the Switch through the Console or Telnet Interface
Upgrade / Backup
Select Edit to the switch via the console port, the active image is replaced. Active Image
The Active Image screen shows information about the active image file and...
Administration Guide - Page 55
....168.100.20.
Accessing the Web-based Utility
To access the web-based utility, enter the IP address of the Ethernet switch to the address field of a Linksys One system, the easiest way to find its IP address via DHCP on the default VLAN 100. To access on-line help functionality for more details on the right side of the Ethernet...
Administration Guide - Page 65
....3af POE (SGE2000P only), 802.1d STP, 802.1Q/p VLAN, 802.1w Rapid STP, 802.1s Multiple STP, 802.1x Port Access Authentication
• 24 RJ-45 connectors for 10BASE-T/100BASE-TX/1000Base-T with 4 shared Gigabit SFP slots
• Console port • Auto MDI/MDI-X • Autonegotiate/Manual setting • RPS port for connecting to Redundant Power Supply unit...
Cisco SGE2000P Reviews
We have not received any reviews for Cisco yet.