Cisco 1131 - Aironet 802.11G Integrate Support and Manuals
Get Help and Manuals for this Cisco item
Cisco 1131 Videos
Imagen 1131
Duration: 2:35
Total Views: 2
Duration: 2:35
Total Views: 2
Telindus 1131 ADSL router no packets
Duration: 1:15
Total Views: 133
Duration: 1:15
Total Views: 133
Configuración de dispositivo Cisco Switch AP 1131
Duration: 1:15
Total Views: 268
Duration: 1:15
Total Views: 268
Cisco Air AP-1131 boot lights
Duration: 2:01
Total Views: 4,241
Duration: 2:01
Total Views: 4,241
Popular Cisco 1131 Manual Pages
Hardware Installation Guide - Page 16
... do not support Wireless Domain Services (WDS). However, the controller provides functionality equivalent to WDS when the access point associates to autonomous mode). The lightweight 1131G access point contains one integrated radio: a 2.4-GHz radio (IEEE 802.11g). The controller manages the configuration, firmware, and controls transactions such as opposed to it an LWAPP join request. When...
Hardware Installation Guide - Page 18
... page 3-1 or the "Troubleshooting Lightweight Access Points" section on page 4-1.
• The Status LED provides general operating status and error indications (top cover closed).
• The Ethernet LED is hidden by the closed to view the Status LED but the cover must be closed top cover (see Figure 1-1). Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
1-4
OL-8369-05...
Hardware Installation Guide - Page 25
... bridge
Network Example with Lightweight Access Points
In Figure 1-8, the autonomous unit is configured in Layer 3 configurations use IP addresses and UDP packets, which can be routed through large networks. Figure 1-9
Typical Lightweight Access Point Network Configuration Example
LWAPP
OL-8369-05
LWAPP
158085
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide...
Hardware Installation Guide - Page 51
... • Resetting to the Cisco Technical Support and Documentation website at the following URL: http://www.cisco.com/cisco/web/psa/default.html Sections in this chapter include: • Checking the Autonomous Access Point LEDs, page 3-2 • Checking Basic Settings, page 3-4 • Low Power Condition for basic problems with the autonomous access point (model: AIR-AP1131AG or AIR-AP1131G...
Hardware Installation Guide - Page 55
... an access point in the Enable Radio field. The access point default SSID is not supported in the Enable Radio field. Note The default SSID (tsunami) is tsunami. Refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for instructions on setting the access point's WEP keys. Chapter 3 Troubleshooting Autonomous Access Points
Checking Basic Settings
Enable Radio...
Hardware Installation Guide - Page 56
... Cisco Aironet power injectors are capable of power. Low Power Condition for Autonomous Access Points
Chapter 3 Troubleshooting Autonomous Access Points
Security Settings
Wireless clients attempting to authenticate with your access point must support the same security options configured in the client adapter and for the client adapter driver and firmware versions that appears on the Status...
Hardware Installation Guide - Page 62
... Access Points
Chapter 3 Troubleshooting Autonomous Access Points
Configuring the Access Point System Power Settings Using a Browser
You can also use your browser pop-up blocker. The power source must comply with MAC Address (unchecked)
Cisco Switch Power Command power inline never power inline auto
power inline auto
3-12
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide...
Hardware Installation Guide - Page 66
... to the Default Configuration
Chapter 3 Troubleshooting Autonomous Access Points
Resetting to the Default Configuration
If you forget the password that allows you to configure the access point, you may need to 3 seconds), and release the button. Press and hold the MODE button while you reconnect power to receive an IP address using the Web browser interface, the Telnet interface, or Cisco IOS...
Hardware Installation Guide - Page 67
...MODE button.
Chapter 3 Troubleshooting Autonomous Access Points
Reloading the Access Point Image
Step 2 Step 3
Step 4 Step 5 Step 6
Enter the access point's IP address in the same subnet as c1130-k9w7-tar.123-8.JA.tar) into the TFTP server folder on a PC connected to upgrade the firmware image. Note If the access point is Cisco.
Activate the TFTP server. The username and password...
Hardware Installation Guide - Page 68
...the Access Point Image
Chapter 3 Troubleshooting Autonomous Access Points
Step 5
Step 6 Step 7
Step 8 Step 9
Step 10
If using in-line power, use a Category 5 (CAT5) Ethernet cable to connect your PC. Hold the MODE button until the Radio LED turns a red color (approximately 20 to the access point. After the access point reboots, you to browse to the access point.
Follow these instructions...
Hardware Installation Guide - Page 78
... inline power sources are disabled), Cisco IOS software loads and runs, and power negotiation determines if sufficient power is connected to negotiate with a Cisco switch for full operation. In low power mode, the access point activates the Status LED low power error indication (see the "Checking the Lightweight Access Point LEDs" section on the access point might cause the access point to...
Hardware Installation Guide - Page 79
... power injector on the switch port
• Use the 48-VDC power module to locally power the access point
Configuring Power Using Controller CLI Commands
Intelligent Power Management support is dependent on the controller and is the MAC address of the switch port to which the access point is providing power to support Intelligent Power Management. If your Cisco switch is capable of supplying...
Hardware Installation Guide - Page 80
... power inline never
Power injector used by the access point to connect with new controller settings, but the static IP addresses for information on when to use of a power injector at the switch. Manually Configuring Controller Information Using the Access Point CLI
In a new installation, when your access point is not associated to determine which Cisco IOS release supports Intelligent Power...
Hardware Installation Guide - Page 82
... Mode
Chapter 4 Troubleshooting Lightweight Access Points
Using a WLAN Controller to Return the Access Point to Autonomous Mode
Follow these steps to return a lightweight access point to autonomous mode using the access point MODE button and a TFTP server:
Note The access point MODE button is enabled by default, but you reconnect power to the access point. Wait until the Radio LED turns red...
Hardware Installation Guide - Page 92
... device may cause undesired
operation.
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Autonomous Access Point Models: AIR-AP1131AG-E-K9 AIR-AP1131G-E-K9
Lightweight Access Point Models: AIR-LAP1131AG-E-K9 AIR-LAP1131G-E-K9
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
B-4
OL-8369-05 This device must accept any interference received, including...
Cisco 1131 Reviews
We have not received any reviews for Cisco yet.