Users Manual - English
Page 235
Error 139 No Paper 140 Out of Memory 141 Print Unable XX 141 Scan Unable XX 142 Extension telephone, using 61 External telephone, connecting ...messages on paper 52 retrieving from a remote site ....... 76, 77 ring delay, setting 50 sequential polling 78 G telephone line interference 138 sending 38 at end of conversation 53 easy receive 51 fax forwarding 77 fax ...receive stamp 53 from extension telephone 60, 61 into memory (fax storage 72 paging 72 polling receive 78 reducing to load 20, 21 jam 145 Drum unit checking (remaining life 166 cleaning 156, 157 ...
Error 139 No Paper 140 Out of Memory 141 Print Unable XX 141 Scan Unable XX 142 Extension telephone, using 61 External telephone, connecting ...messages on paper 52 retrieving from a remote site ....... 76, 77 ring delay, setting 50 sequential polling 78 G telephone line interference 138 sending 38 at end of conversation 53 easy receive 51 fax forwarding 77 fax ...receive stamp 53 from extension telephone 60, 61 into memory (fax storage 72 paging 72 polling receive 78 reducing to load 20, 21 jam 145 Drum unit checking (remaining life 166 cleaning 156, 157 ...
Service Manual
Page 82
...36 Fax scanning error (Error) A6 Fuser error other than 58, 59, 3-30 DD 68, 69, 6A, 6B, 6C, 6D, 6E, 6F, 3-36 76, 78, DE and E2 are occurred Scanning color parameter file A7 failure Central temperature of memory for scanning 3-32 89 Incorrect paper size in Fax List.../ 3-23 AD Report) 3-31 Discharge detection error (Unable CCD unit home position sensor to print after the discharge is not turned on. Error codes Problem Refer Error to: codes Problem Refer to: Fax paper setting mismatch 7F...
...36 Fax scanning error (Error) A6 Fuser error other than 58, 59, 3-30 DD 68, 69, 6A, 6B, 6C, 6D, 6E, 6F, 3-36 76, 78, DE and E2 are occurred Scanning color parameter file A7 failure Central temperature of memory for scanning 3-32 89 Incorrect paper size in Fax List.../ 3-23 AD Report) 3-31 Discharge detection error (Unable CCD unit home position sensor to print after the discharge is not turned on. Error codes Problem Refer Error to: codes Problem Refer to: Fax paper setting mismatch 7F...
Service Manual
Page 93
Rapid temperature rising failure (center thermistor) Error code 78 Print Unable 78 Turn the power off and then back on again. Replace the main PCB ASSY. ■ Error code 7D Drum Error Open the Front Cover and ... fuser unit. 2 Main PCB failure Replace the main PCB ASSY. ■ Error code 7A Print Unable 7A See Troubleshooting and routine maintenance chapter in the drum unit. • Replace the drum unit with a new one. ■ Error code 76 Print Unable 76 Turn the power off and then back on again. Step 1 2 3 Cause Dirt or...
Rapid temperature rising failure (center thermistor) Error code 78 Print Unable 78 Turn the power off and then back on again. Replace the main PCB ASSY. ■ Error code 7D Drum Error Open the Front Cover and ... fuser unit. 2 Main PCB failure Replace the main PCB ASSY. ■ Error code 7A Print Unable 7A See Troubleshooting and routine maintenance chapter in the drum unit. • Replace the drum unit with a new one. ■ Error code 76 Print Unable 76 Turn the power off and then back on again. Step 1 2 3 Cause Dirt or...
Service Manual
Page 108
.... 3-36 Confidential Central temperature of heat roller detected the temperature that was lower than 58, 59, 68, 69, 6A, 6B, 6C, 6D, 6E, 6F, 76, 78, DE and E2 are occurred. Step Cause Remedy 1 Fuser unit failure Replace the fuser unit. 2 Main PCB failure Replace the main PCB ASSY. 3 LVPS PCB... rear PCB ASSY connection Reconnect the relay rear PCB ASSY failure connector correctly. 2 Main PCB failure Replace the main PCB ASSY. ■ Error code E0 Print Unable E0 Turn the power off and then back on again.
.... 3-36 Confidential Central temperature of heat roller detected the temperature that was lower than 58, 59, 68, 69, 6A, 6B, 6C, 6D, 6E, 6F, 76, 78, DE and E2 are occurred. Step Cause Remedy 1 Fuser unit failure Replace the fuser unit. 2 Main PCB failure Replace the main PCB ASSY. 3 LVPS PCB... rear PCB ASSY connection Reconnect the relay rear PCB ASSY failure connector correctly. 2 Main PCB failure Replace the main PCB ASSY. ■ Error code E0 Print Unable E0 Turn the power off and then back on again.