Brother International CE8080/CE8080PRW Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International CE8080/CE8080PRW manuals!
Problems with Brother International CE8080/CE8080PRW?
Ask a Question
Free Brother International CE8080/CE8080PRW manuals!
Problems with Brother International CE8080/CE8080PRW?
Ask a Question
Popular Brother International CE8080/CE8080PRW Manual Pages
Operation Manual - Page 4
... locations. For additional product information, visit our web site at www.brother.com
SAVE THESE INSTRUCTIONS
This machine is required, first follow the troubleshooting table in the back of the appliance in should be used .
• Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other hot objects.
•...
Operation Manual - Page 6
... is available through your authorized dealer. (Part code: 132730-122) ● The included accessories vary depending on the model you purchased, the following accessory may be included with product code 888-E30/E31/E37/E38/E39/V61/... the presser foot holder is on machine.)
SA156
SFB: XA5539-151
10 Needle set
XC8834-021
11 Twin needle
131096-121
12
Ball point needle (gold colored)
...
Operation Manual - Page 8
.... j Bobbin cover k Needle plate The needle plate is marked with the quick-set bobbin (for models equipped with guides for models equipped with the needle threader) (page 17)
b Buttonhole lever (page 34 and 42) c Presser foot holder
The presser foot is installed onto the presser foot holder. c Needle position button Press this controller to hold...
Operation Manual - Page 16
...models equipped with your finger, and then pass the thread
through the slit, as shown. • If the thread is not correctly inserted through the tension-adjusting spring of the thread, push the bobbin e down the bobbin, guide...
Slide the button and open the cover. Replace the bobbin cover. a Slit b Cutter
...with the quick-set bobbin
Memo
● The direction for models equipped with the ...
Operation Manual - Page 17
...to sew, follow the instructions. Upper threading
Set the upper thread and thread the needle. • For details on the sewing machine. Fully insert the spool for models equipped with the
needle ...for the upper thread onto e the spool pin.
Turn on the needle threader, see page 17. Replace the bobbin cover. a Mark
b Needle position button
• If the needle is not raised, ...
Operation Manual - Page 19
... injured. While lowering the needle threader lever, hook c the thread onto the guide.
1
a Needle holder b Needle threader
lever c Guide
Fully lower the needle threader lever.
b
The hook passes through ...threader cannot be used with force or it may cause sewing problems.
■ Using the needle threader (for models equipped with the needle threader). If you accidentally step on ...
Operation Manual - Page 20
... of the upper thread, raise b the needle either by pressing (needle position button) (for models equipped with the quick-set bobbin You can begin sewing immediately without cutting it.
• The bobbin cover should still be left over.
Replace the bobbin cover. a Presser foot lever
Pass the end of the thread as described...
Operation Manual - Page 23
...
Note
Models equipped with bent needles. Pass the thread through i of the d bobbin winder shaft. Install the thread spool and thread the upper e thread.
a Needle bar thread guide
Attach ...machine. Manually thread the left needle with this machine (part code: 131096-121).
● Do not sew with a needle threader ● You cannot use the needle threader to back.
Turn on installing a ...
Operation Manual - Page 24
...models equipped with the twin needle, refer to raise the needle from the fabric, and then raise the presser foot lever and turn the fabric. X Two lines of thread and fabric that have chosen.
CAUTION
● Before replacing...used . If you have been designed to be sure to "STITCH SETTINGS" (page 50).
KNOWING YOUR SEWING MACHINE
Select a stitch.
If the needle hits the presser foot,...
Operation Manual - Page 27
..., slowly turn the handwheel toward you (counterclockwise) and check that the mark on the foot controller. (With g models equipped with the start /stop button), if the
foot controller is changed from the standard setting, around or disappears from the LCD.
a Sewing speed controller
Slowly press down on the
wheel points up. (With...
Operation Manual - Page 28
... side of each other. For details, refer to start /stop button)) (for models equipped with reverse stitching, pressing (reverse/reinforcement stitch button) sews reinforcement stitches, ...Whether reverse stitches or reinforcement stitches are secured with the start /stop button cannot be used to "STITCH SETTINGS" (page 50). In this case, refer to "Lower threading" (page 13) and rethread the ...
Operation Manual - Page 38
...two pieces of zippers, and can easily position it to the shortest setting by g pressing the stitch length adjustment key.
Turn the handwheel toward...model 60/70 stitches model 50 stitches model 40 stitches model 30 stitches model 20 stitches model
Straight stitch (center)
I 01 01 01 01 01 01 01
CAUTION
● Be sure to turn the handwheel to
and
turn off the main power before replacing...
Operation Manual - Page 52
...model 70 stitches model 60 stitches model 50 stitches model 40 stitches model 30 stitches model 20 stitches model Twin Needle Walking Foot Reverse (Rev.)/ Reinforcement (Rfc.)
Stitching
APPENDIX
4 APPENDIX
STITCH SETTINGS
Applications, stitch lengths and widths and whether the twin needle can be damaged. Stitch Name/ Application
Stitch Width Stitch Length [mm (inch.)] [mm (inch.)]
Auto Manual...
Operation Manual - Page 60
For a new bobbin case (part code: XE7560-001), contact your nearest authorized service center.
● Make sure that you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. If the problem persists, contact your fingers touch the race.
From the front, slide the needle plate cover back i into the hole in the...
Operation Manual - Page 70
... performed you will hear two or four beeps (only for models equipped with the operation beep).
■ If a key...service center.
After cleaning the race, insert the bobbin case properly. If the needle is lowered.
APPENDIX
ERROR MESSAGES
If an operation is performed incorrectly before the sewing machine is set up because the thread is moved to the right. Follow the instructions...
Brother International CE8080/CE8080PRW Reviews
We have not received any reviews for Brother International yet.