Brother International CE-5500/CE-5500PRW Support and Manuals
Get Help and Manuals for this Brother International item
This item is in your list!
View All Support Options Below
Free Brother International CE-5500/CE-5500PRW manuals!
Problems with Brother International CE-5500/CE-5500PRW?
Ask a Question
Free Brother International CE-5500/CE-5500PRW manuals!
Problems with Brother International CE-5500/CE-5500PRW?
Ask a Question
Popular Brother International CE-5500/CE-5500PRW Manual Pages
Operation Manual - Page 4
..., it must be replaced by the manufacturer as contained in this machine, avoid direct sunlight and high humidity locations. For additional product information, visit our web site at www.brother.com
SAVE THESE INSTRUCTIONS
This machine is not suitable
for household use outdoors.
8 For a longer service life:
• When storing this manual. Never use plugs...
Operation Manual - Page 6
...or damaged, contact your authorized dealer. (Part code: 132730-122) ● The included accessories vary depending on the model you purchased, the following accessory may be included with product code 888-E30/E31/E37/E38/E39/V61... separately. If any item is on machine.)
SA156
SFB: XA5539-151
10 Needle set
XC8834-021
11 Twin needle
131096-121
12
Ball point needle (gold colored)
XD0360...
Operation Manual - Page 8
...presser foot section
a Needle threader (for models equipped with the quick-set bobbin (for models equipped with guides for sewing straight seams. l Needle bar thread guide (page 16) m Presser foot lever ...opposite direction. a LCD (liquid crystal display)
The number of sewing while the button is installed onto the presser foot holder. j Bobbin cover k Needle plate The needle plate is marked...
Operation Manual - Page 16
... the bobbin in so the thread comes out in the diagram).
■ For models equipped with the needle position button), and raise the presser foot lever.
14
a Tension-adjusting spring
Replace the bobbin cover.
f
CAUTION
● Make sure you set the bobbin so the thread unrolls in the right direction. KNOWING YOUR SEWING...
Operation Manual - Page 17
... the bobbin thread before threading the sewing machine.
Fully insert the spool for models equipped with the
needle position button) once or twice to draw up d ...start to sew, follow the instructions. Turn on the wheel points up the bobbin thread. a Mark
b Needle position button
• If the needle is set incorrectly, the thread may bend ... spool pin.
Replace the bobbin cover.
Operation Manual - Page 19
...When using the needle threader (for models equipped with the needle threader)
...Guide
Fully lower the needle threader lever. Lower the presser foot lever. a Hook b Thread
Release the needle threader lever.
Follow steps a through the eye of the thread. j
CAUTION
● Make sure you could be used with force or it may cause sewing problems.
■ Using the needle threader (for models...
Operation Manual - Page 20
...set bobbin You can draw up the lower thread by hand so that the mark on the wheel points up or by turning the handwheel
toward the back of the machine
under the presser foot. Before you may cause sewing problems.
Drawing up the bobbin thread. c
REPLACING...Needle position button
a Upper thread b Lower thread
■ For models equipped with the needle position button) once or twice.
g
a ...
Operation Manual - Page 23
...Memo
● When setting the thread spool, set it so that have been made for making decorative stitches. a Needle bar thread guide
Attach zigzag foot "J". (Refer to page 22.)
h
Note
Models equipped with a needle...break or the
machine may damage the machine.
Install the twin needle. Thread the upper thread for the left needle with this machine (part code: 131096-121).
● Do not sew ...
Operation Manual - Page 24
...otherwise injuries may cause injury.
● Use presser feet that are sewn parallel to "STITCH SETTINGS" (page 50). If you use the correct presser foot for the stitch pattern you (counterclockwise) and... presser foot
Replace the presser foot as described below.
Start sewing. If you leave the power on and step on the wheel points up. (With models equipped with (needle position button),...
Operation Manual - Page 27
... needle to "Sewing speed controller (for models equipped with (start /stop button), if the
foot controller is changed from the standard setting, around or disappears from the LCD. ...of thread toward a you (counterclockwise) and check that the mark on the foot controller. (With g models equipped with the start /stop button)" (page 9).
a Presser foot lever
Place the fabric under the ...
Operation Manual - Page 28
...tension
The thread tension will stay up . (With models equipped with reverse stitching, pressing (reverse/reinforcement stitch button) sews reinforcement stitches, 3 to 5 stitches on setting the machine so that the needles stay up when ...once or twice.) This procedure is not necessary if the needle stop position has been set so that the thread is selected. If the thread is not shown as too ...
Operation Manual - Page 38
... b sides facing each other. UTILITY STITCHES
Select a stitch . (With models not provided e with stitch , select stitch .)
Adjust the stitch width ...reverse/reinforcement stitch button) to turn the handwheel to the shortest setting by g pressing the stitch length adjustment key.
When you h ...turn off the main power before replacing the presser foot.
Open the seam allowance, press it from ...
Operation Manual - Page 52
...Application
Stitch Width Stitch Length [mm (inch.)] [mm (inch.)]
Auto Manual
Auto Manual
Straight stitch (Left) J 00 00 00 00 00 00 00 00...model 90 stitches model 80 stitches model 70 stitches model 60 stitches model 50 stitches model 40 stitches model 30 stitches model 20 stitches model Twin Needle Walking Foot Reverse (Rev.)/ Reinforcement (Rfc.)
Stitching
APPENDIX
4 APPENDIX
STITCH SETTINGS...
Operation Manual - Page 60
...Frequent troubleshooting topics
Detailed causes and remedies for common troubleshooting topics are aligned
before installing the .... TROUBLESHOOTING
If the machine stops operating correctly, check the following possible problems before contacting us at " http:// support.brother.com... new bobbin case (part code: XE7560-001), contact your dealer or the nearest authorized service center. If you ...
Operation Manual - Page 70
...error, and correct it before continuing the operation. Otherwise, operate the machine by using the foot controller. Clean the race to the right. Follow the instructions...sewing machine beeps for models equipped with the operation beep)
... stops.
Contact your nearest authorized service center. A stitch other than ...set up because the thread is bent or broken, replace the needle.
Brother International CE-5500/CE-5500PRW Reviews
Do you have an experience with the Brother International CE-5500/CE-5500PRW that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Brother International yet.
Earn 750 points for your review!