Whirlpool YGY399LXUS Support Question
Whirlpool YGY399LXUS Support Question
Find answers below for this question about Whirlpool YGY399LXUS.Need a Whirlpool YGY399LXUS manual? We have 1 online manual for this item!
Question posted by curtisandre on January 8th, 2013
How Do You Replace The Small Element Under The Stove Top. Thanks
I need a little help on how to do it, the manual does not state the repairs
Current Answers
Related Whirlpool YGY399LXUS Manual Pages
Installation Instructions - Page 2
... to rear range foot.
Connect anti-tip bracket to children and adults.
2 Reconnect the anti-tip bracket, if the range is the ...all safety messages. This is moved. WARNING
You can tip the range and be killed or seriously injured if you what the potential ...
WARNING
Tip Over Hazard A child or adult can be killed. RANGE SAFETY
Your safety and the safety of injury, and tell you don...
Installation Instructions - Page 3
...50 amps that is adequate as long as it must be used will need to be rated at back of cooktop
*Range can be reduced by reaching over heated surface units, cabinet storage space.... Model/serial number plate (located behind the storage drawer panel.
■ The range should be
secured to sub-floor. Tools needed If using a power supply cord: ■ A UL listed power supply cord kit...
Installation Instructions - Page 4
...voltage and frequency as to the cabinet.
The ground must be using and follow the range hood or microwave hood combination installation instructions for new branch-circuit installations (1996 NEC);...50
*The NEC calculated load is recommended that a qualified electrical installer determine that the range can be connected directly to the top of the 4-wire power supply cord is ...
Installation Instructions - Page 5
... terminals with a CSA International Certified Power Cord intended to a 3-wire system: Local codes may need trim cut back ³⁄₈" (1.0 cm) from :
Canadian Standards Association 178 Rexdale Blvd... Place level on the appliance end must be plugged into a standard 14-50R wall receptacle. Range must be identified by a green or green/yellow cover and the neutral conductor by a white...
Installation Instructions - Page 6
... of another. This may be installed on its back, take 4 cardboard corners from the range. Cardboard cross support
5. Repeat with the range supported on its back.
6. When the range is at the correct height, check that is needed to rear range foot. Remove oven racks and parts package from centerline, as shown. Failure to follow...
Installation Instructions - Page 7
... three 10-32 hex nuts from the middle post of the determined mounting method.
Failure to the bracket holes of the terminal block.
7 Electrically ground range. Using the Phillips screwdriver, mount anti-tip bracket to remove cover.
3. Only
Direct Wire
WARNING
WARNING
Electrical Shock Hazard Disconnect power before servicing. Disconnect power...
Installation Instructions - Page 8
...;CWGEIQCTR!EATUUCRRRESAICTCEESAOLORD
A.
NUCPQTUROAUSSERRIEMWTADEOLIÓTCAVLNHOSAENEPTTELEOAUTÉCWGEIQCTR!EATUUCRRRESAICTCEESAOLORD
■ Replace cord/conduit plate and insert screws.
8 Style 1: Power supply cord strain relief ■ Assemble a UL listed strain relief in the following illustration. A
■ Lift range back panel up and off. Style 2: Direct wire strain relief...
Installation Instructions - Page 9
...4-wire connection: Direct wire
3-wire receptacle (NEMA type 10-50R)
A UL listed, 250-volt minimum, 40-amp, range power supply cord
3-wire connection: Power supply cord
3-wire direct
1" (2.5 cm)
3" (7.6 cm)
A fused disconnect ... be cut out and removed. Ground-link screw C. Replace back panel and screws on bottom of range. Terminal block B. Ground-link screw
2. Use Phillips screwdriver...
Installation Instructions - Page 10
... wiring to the fuse disconnect or circuit breaker box. D B
C
A. 10-32 hex nut B. Line 2 (red)
3. Terminal block B.
Replace terminal block access cover.
3-wire connection: Power Supply Cord
Use this method for use with ranges.
8. Ground-link screw
D. Neutral (center) wire F. Feed the power supply cord through the
neutral
10 Connect line 1 (black...
Installation Instructions - Page 11
...Neutral (white) wire E. Line 1 (black) C. Replace terminal block access cover.
11 Save the ground-link screw and the end of the range. Pull the conduit through the strain relief on cord/conduit...Wire Torque Specifications Attaching terminal lugs to torque shown in . (4.0 N-m)
5. Part of range. Ground-link screw C. Ground-link screw
E. Securely tighten set screw on bottom of...
Installation Instructions - Page 12
....
3.
Terminal lug B. Line 1 (black) wire
D. Line 2 (red) wire E. Attach terminal lugs to back. Terminal lug
4. Replace terminal block access cover. Making sure the anti-tip bracket is installed:
■ Look for satisfactory baking conditions.
12 Push range back into position.
4. Line 2 (red) F. Connect line 1 (black) and line 2 (red) wires to the outer...
Installation Instructions - Page 13
...; Disconnect power. 2. Turn power on surface burners and oven. For power supply cord-connected ranges: 1. Complete cleaning or maintenance. 4. For direct-wired ranges:
WARNING
Electrical Shock Hazard Disconnect power before operating. Replace all packaging materials. 4. If removing the range is under anti-tip bracket. Check that anti-tip bracket is connected. ■ See...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
I need information about the coil elements and burner bowls on my electric range
... do I need assistance in the burner bowl with the coil element receptacle. NOTE: Before removing or replacing coil elements and burner bowls, make sure they are cool and the control knobs are in the edge of elements and burner bowls . To replace: Line up cooktop on my electric range. My oven is not working. They also help catch... -
I need replacement parts for my convertible range hood
... work right, because they are made to the same exacting specifications used to order replacement parts, we recommend that If you only use that you need replacement parts for my convertible range hood I clean my frost-free freezer? filter . How do I need to build every new Whirlpool appliance. Or, you check out to... -
What are some tips for home canning using my electric modular downdraft cooktop?
...manual for best results. Reduce heat setting to the lowest position needed to the cooktop. Refer to your cooktop: Use flat-bottomed canners/pans for specific instructions. To prolong the life of the elements: Prepare small... with hot water. Do not place the canner on high. How can I use elements for Home Canning? Keep reflector bowls clean for best results. This reduces the time ...
Similar Questions
Breaker Needed For This Stove Top Please Model Number Rf111pxsq 3
running 8 3 wire for this stove need a breaker amp size for this stove thank
running 8 3 wire for this stove need a breaker amp size for this stove thank
(Posted by rayszone 7 years ago)
Broil Ans.convect.beat No Go
My model is.whirlpool ygy399lx....., had to replace convect fan assy due To burned element. Install ...
My model is.whirlpool ygy399lx....., had to replace convect fan assy due To burned element. Install ...
(Posted by sdlj 8 years ago)
Putting Panel On Stove Door Back Together After Cleaning Please Help Me!
I need help. Took apart the oven door to clean. Loosen the screws that held the handle and the side ...
I need help. Took apart the oven door to clean. Loosen the screws that held the handle and the side ...
(Posted by cathie93427 8 years ago)
Cant Find Location Of Bake Element?
please provide answer, only place i think it is under oven above storage door. thanks
please provide answer, only place i think it is under oven above storage door. thanks
(Posted by bod48 10 years ago)