Whirlpool YGY399LXUS Support Question
Whirlpool YGY399LXUS Support Question
Find answers below for this question about Whirlpool YGY399LXUS.Need a Whirlpool YGY399LXUS manual? We have 1 online manual for this item!
Question posted by sdlj on January 28th, 2016
Broil Ans.convect.beat No Go
My model is.whirlpool ygy399lx....., had to replace convect fan assy due To burned element. Install new convect assy, convect fan work, but still no heat from broil element and convect élément, heat only from bottom élément. Check both element continuity all ok. Is there a fuse in the wiring circuit.ThanksDaniel
Current Answers
Answer #1: Posted by Odin on January 29th, 2016 8:05 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
See http://www.repairclinic.com/RepairHelp/Range-Stove-Oven-Repair/13-5--WUdZMzk5TFhVUw==/Whirlpool-Range-Stove-Oven-Troubleshooting. The links most likely to solve are listed third and fourth.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Whirlpool YGY399LXUS Manual Pages
Installation Instructions - Page 2
...
You can be killed. We have provided many important safety messages in death or serious burns to follow the safety alert symbol and either the word "DANGER" or "WARNING." WARNING
Tip Over... Hazard A child or adult can tip the range and be killed or seriously injured if you don't follow instructions. RANGE SAFETY
Your safety and the safety of injury, and tell you...
Installation Instructions - Page 3
... surface units should be rated at back of 5" (12.7 cm) beyond 24" (61 cm) base cabinet.
3 Model/serial number plate (located behind the storage drawer panel.
■ The range should be located for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with upturned ends.
■ A UL listed strain relief. Parts needed
■ Tape...
Installation Instructions - Page 4
...40- or 50-amp, range power supply cord (pigtail) must be using and follow the range hood or microwave hood combination installation instructions for new branch-circuit installations (1996 NEC); If local... at each end of the cooktop, see Range Rating chart below).
Grounding through the neutral conductor.
The model/serial number rating plate is prohibited for dimensional...
Installation Instructions - Page 5
... circuit breaker is recommended.
■ This range is equipped with a CSA International Certified Power Cord intended to be Type SRD or SRDT with a qualified electrical installer if you have molded edge shaved flat ³...cord with local codes.
If you are in a NEMA Type 10-50P plug on the model/serial rating plate.
**If connecting to a 3-wire system: Local codes may need trim cut...
Installation Instructions - Page 6
... centerline, as shown. WARNING
Tip Over Hazard A child or adult can be done with the range supported on top of 1" (2.5 cm). Install Anti-Tip Bracket
1. Determine which mounting method to remove. 8. Position mounting bracket in death or serious burns to children and adults.
2. Storage drawer B. Pull cardboard bottom firmly to use: floor or...
Installation Instructions - Page 7
Use a new 40 amp power supply cord. Use Phillips screwdriver to the wall or floor with the two... to remove cover.
3. Plug into a grounded outlet. Anti-tip bracket
5. Electrical Shock Hazard Disconnect power before servicing. Electrically ground range. Use 8 gauge copper or 6 gauge aluminum wire. Disconnect power.
2. Remove plastic tag holding three 10-32 hex nuts from ...
Installation Instructions - Page 8
... the power supply cord.
■ Use Phillips screwdriver to remove screws from panel on bottom of range.
■ Position cord/conduit plate as shown in the opening in the cord/conduit plate on back of range. NUCPQTUROAUSSERRIEMWTADEOLIÓTCAVLNHOSAENEPTTELEOAUTÉCWGEIQCTR!EATUUCRRRESAICTCEESAOLORD
■ Replace cord/conduit plate and insert screws.
8 Add strain relief. 4.
Installation Instructions - Page 9
... the
neutral 1. Replace back panel and screws on bottom of range. ■ Assemble a UL listed conduit connector in the cord/conduit plate on rear of range. 6. Feed the power supply cord through the strain relief in the opening. Cord/conduit plate D. Removable retaining nut B. A B C
A. Metal ground strap B. B
A. Complete installation following instructions for : ■ New branch...
Installation Instructions - Page 10
... screw C. Line 2 (red)
6. Replace terminal block access cover.
3-wire connection: Power Supply Cord
Use this method for: ■ New branch-circuit installations (1996 NEC) ■ Mobile homes ...
3. Ground-link screw C. Allow enough slack in the cord/conduit plate on your type of range. Securely tighten hex nuts. Cord/conduit plate D. Neutral (center) wire F. Securely tighten hex...
Installation Instructions - Page 11
... posts with the ground-link screw. The ground wire must not contact any other terminal.
6. Bare (green) ground wire D. Line 2 (red) G. Replace terminal block access cover.
11 Part of the range. Metal ground strap B. Allow enough slack to easily attach wiring to the terminal block - 20 lbs-in. (2.3 N-m)
Wire Awg
Torque
8 gauge...
Installation Instructions - Page 12
... block post with anti-tip bracket. Attach terminal lugs to neutral supply wire. 1. Line 2 (red) F. Replace terminal block access cover. Making sure the anti-tip bracket is installed:
■ Look for satisfactory baking conditions.
12
B
C
D
E
Level Range
1. Line 1 (black) wire
D. Cord/conduit plate
D.
A. Terminal lug B. Line 2 (red) wire
Bare Wire Torque Specifications...
Installation Instructions - Page 13
... its final location. See the Use and Care Guide for heat. Unplug the power supply cord. 3. Failure to avoid damaging the floor covering.
If there is level. Read "Range Use" in power supply cord. 5. Replace all parts are not bent. 8. Check that the range is an extra part, go back through the steps to...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Dryer does not heat - Electric dryer
... 2 household fuses or circuit breakers. If the problem continues, call an electrician. My dryer will not start The drum may not have heat. Did you may be incorrectly installed. Review the Installation Instructions to make sure that the power supply cord is properly installed. My electric dryer does not heat. Replace the fuses or reset the circuit breakers. -
The cooking time using my SpeedCook microwave oven with convection seems too long
... only this appliance. or 20-amp electrical supply with convection seems too long. Recommended: A time-delay fuse or time-delay circuit breaker. For example,70% = 7 = Medium-High. 100% (Default setting): Heating rice, pasta or casseroles. Larger amounts of food being heated? Many recipes for microwave cooking specify which cooking power to use by percent... -
My range is not working at all
...Replace the fuse(s) or reset the circuit breaker(s). If the problem continues, call for gas ranges...Model # Is the display showing a letter followed by a number? Press OFF to ignite My gas range cooktop burners are not functioning My gas oven won't operate Why is not working. Is the power cord plugged in your Use and Care Guide. Has a household fuse(s) blown or has a circuit...
Similar Questions
During Convection Or Airfry Mode The Fan Does Not Stay On Continuously.
Isn't suppose to stay on. I thougth the heating elements is what cycled
Isn't suppose to stay on. I thougth the heating elements is what cycled
(Posted by Anonymous-174373 9 months ago)
Whirlpool Model Xfc31050ab Shows F9eo Status Stove Top Works...oven Doesn't.
How to remove F9eo status on whirlpool oven. Oven never been used? stove model Xfc31050ab
How to remove F9eo status on whirlpool oven. Oven never been used? stove model Xfc31050ab
(Posted by Katrinabyrd11 9 years ago)
I Have No Power At My Oven. Checked Everything. It Should. Fuse In Oven?
(Posted by winyahreds 9 years ago)
How Do You Lift The Range Top? Brand New And One Burner Not Working.
(Posted by jsgranch 10 years ago)
How Do You Replace The Small Element Under The Stove Top.
Thanks
I need a little help on how to do it, the manual does not state the repairs
I need a little help on how to do it, the manual does not state the repairs
(Posted by curtisandre 11 years ago)