Home » Troy-Bilt » Lawn & Garden » Troy-Bilt TB675

Troy-Bilt TB675 Support Question

Find answers below for this question about Troy-Bilt TB675.
Need a Troy-Bilt TB675 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-154291 on September 26th, 2015

Troy-bilt Tb675 Overheating

My Troy-Bilt TB675 overheats after running for a short time. Is this common with these models ?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TommyKervz on September 27th, 2015 2:35 AM

This answer was accepted by the poster of the original question.

TommyKervz

Member since:
January 10th, 2013

Points: 17,776,803

1,100
points

REPLACING THE TRIMMING LINE: Only use the trimming line described in the Specifications section. Other types of trimming line may cause the engine to overheat or fail.
Do not remove or alter the line cutting blade assembly. Excessive line length will make the unit overheat.

Hope that is helpful.
Kervz at www.satechhelp.co.za

Related Troy-Bilt TB675 Manual Pages

Operation Manual - Page 1

...period, should only be found on the latest product information available at the time of authorized service dealers near you. Additional information about the unit can be...02 All information, illustrations, and specifications in Canada. Operator's Manual Electric Start Capable 4-Cycle Trimmer TB675 EC TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil ...

Operation Manual - Page 2

... and certain finished components contain or emit chemicals known to the State of California to liability or a fine. DO NOT smoke. • Never start or run the unit inside a closed room or building. Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by...

Operation Manual - Page 3

... from all moving parts. • Do not touch the engine, gear housing or muffler. Do not run the unit at a height to instruct other than the speed needed to the unit, and void the ...speed when not in contact with water or any other liquid. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. OTHER SAFETY WARNINGS • All service, other users. Keep the ...

Operation Manual - Page 4

...Push primer bulb, fully and slowly, 10 times. • CHOKE CONTROL 1. • FULL choke position 2. • PARTIAL choke position 3. • RUN choke position • THROWN OBJECTS AND ...complete safety, assembly, operating and maintenance and repair information. Read the operator's manual for a short time. • SHARP BLADE WARNING: Sharp blade on this unit. • SAFETY & INTERNATIONAL...

Operation Manual - Page 5

... 4-Cycle Displacement 30 cc (1.83 cu. We reserve the right to make changes at the time of printing. in.) Spark Plug Gap 0.025 in . (43.18 cm) * All specifications are ...based on the latest product information available at any time without notice. 5 Other optional accessories may be used with cutting head, cutting head shield and handle 13 -...

Operation Manual - Page 9

...• Use the fuel additive STA-BIL® or an equivalent • Drain the tank and run the engine dry before storing the unit WARNING: DO NOT USE E85 FUEL IN THIS UNIT. As ...ignition for spilled fuel. Reinstall the fuel cap. 6. FUELING THE UNIT WARNING: Gasoline is the most common cause of old fuel according to the unit's fuel tank. Place the fuel container spout into the fill...

Operation Manual - Page 10

... engine should start , begin the starting procedure with a controlled and steady motion 5 times (Fig. 11). 7. IF THE UNIT WAS RUN FOR 10-15 MINUTES AND THE ENGINE IS HOT... Continue to Position 3. The unit may be used during this time. Then move the choke lever to start after a few attempts, move the choke...

Operation Manual - Page 11

... the electric start accessory operator's manual for 2 seconds. 8. Continue to squeeze the throttle control. The unit may be used during this time. Move the choke lever to Position 1 (Fig. 10). 5. Run the electric start , begin the starting position (Fig. 11). 6. Move the choke lever to Position 2 (Fig. 10). 9. Refer to restart the...

Operation Manual - Page 12

...tap the bump knob on the ground while the unit is running. Attempting to the unit. This improves the unit's cutting efficiency...Keep the cutting head parallel to the ground (Fig. 15). Each time the bump knob is at a 30° angle to the ...8226; Stand in the cutting head shield will make the unit overheat. To release more difficult when the cutting line gets shorter. ADJUSTING...

Operation Manual - Page 13

MAINTENANCE SCHEDULE Perform these procedures, take the unit to overheat or fail. NOTE: Please read the California/EPA statement that came with the...cutting head (Fig. 17). MAINTENANCE WARNING: To prevent serious injury, never perform maintenance or repairs while the unit is running. Push the line through the cutting head until the ends are unsure about 5 inches (12.7 cm) protrude from...

Operation Manual - Page 15

... onto the air filter housing. Insert the cover screw into the hole on the air filter housing. The oil will VOID the warranty. 7. Allow ample time for complete drainage. Pour 2.03 fl.oz. (60 ml) of oil. NOTE: Use the empty oil bottle saved from the air filter housing (Fig. 23...

Operation Manual - Page 16

... is idling too quickly, turn the idle speed screw counterclockwise, 1/8 of a turn at a time (as needed ) to Starting and Stopping. 2. If the engine stops, use a small Phillips screwdriver to set the air gap... at a time (as follows: 1. Checking the fuel, cleaning the air filter, and adjusting the idle speed should ...

Operation Manual - Page 17

...the spark plug. 4. Preparing the Unit for any moisture with the engine at the top. Refer to run until it stalls. Wipe off any loose or damaged parts. Store the unit in a dry, well... a fueled unit where fumes may reach an open flame or spark. • Allow the engine to cool. Short-term Storage (1-2 weeks) 1. Remove the spark plug and drain all fuel has been drained from the cylinder. ...

Operation Manual - Page 18

... If further assistance is extended Stop the engine and clean the cutting head Refill the cutting head with fresh fuel Press the primer bulb 10 times Drain the fuel tank and add fresh fuel Replace the spark plug Refer to the IF... PROBLEM THE ENGINE WILL NOT START The fuel tank...

Operation Manual - Page 20

... option, repair or replace, free of any part found to P.O. Troy-Bilt does not extend any product shall bind Troy-Bilt. Wear items - Troy-Bilt reserves the right to change or improve the design of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for products...