Troy-Bilt Storm Tracker 2690 Support Question
Troy-Bilt Storm Tracker 2690 Support Question
Find answers below for this question about Troy-Bilt Storm Tracker 2690.Need a Troy-Bilt Storm Tracker 2690 manual? We have 1 online manual for this item!
Question posted by jamess8007 on March 13th, 2017
How To Adjust
the tension on the steering trigger control for faster turns on the troy Bilt storm tracker 2690XP how do you adjust it can it be adjusted
Current Answers
Answer #1: Posted by waelsaidani1 on March 13th, 2017 6:51 PM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
Adjustments
Shift Cable
If the full range of speeds (forward and reverse) cannot be
achieved adjust the shift cable as follows:
1.
Place the shift lever in the fastest forward speed position.
2.
Loosen the hex nut on the shift cable index bracket. See
Fig. 6-5 here https://www.manualslib.com/manual/484345/Troy-Bilt-Storm-Tracker-2690xp.html?page=17
Related Troy-Bilt Storm Tracker 2690 Manual Pages
Operation Manual - Page 1
... USA
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-07126 (May 02, 2011) FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Track Drive Snow Thrower - Storm Tracker 2690XP
WARNING
READ...
Operation Manual - Page 2
... a range of Contents
Safe Operation Practices 3 Assembly & Set-Up 7 Controls 12 Operation 15 Maintenance & Adjustment 16
Service 19 Troubleshooting 23 Replacement Parts 24 Attachments 25 Warranty Back Cover
Record Product Information
Before setting up , operate and maintain your machine, for purchasing a Troy-Bilt Snow Thrower. Table of product specifications for all engine...
Operation Manual - Page 3
...comply with any adjustments while engine is in this manual before attempting to the eyes.
2. Disengage all instructions in this symbol. Read, understand, and follow all control levers before ...in a safe place for future and regular reference and for all machines with all controls and their proper operation. Important Safe Operation Practices
2
WARNING! Do not operate ...
Operation Manual - Page 4
...front of starter cord (kickback) will pull hand and arm toward engine faster than ½
allow anyone in the discharge or collector openings. Never ... not use .
(e.g. Shut off the engine and equipment. The auger/impeller control lever is
operating on a trailer with the rim of ignition.
8. Never ...adjustments, or inspections. Wait until resistance is spilled on the handles.
Operation Manual - Page 5
... setting or over-speed the engine. to verify they engage and disengage properly and adjust, if necessary. At the end of the Average Useful Life have the machine inspected... serious injury or death, do not meet the original equipment specifications may include the following emission control systems: Engine Modification (EM), Oxidizing Catalyst (OC), Secondary Air Injection (SAI) and Three...
Operation Manual - Page 7
... Shear Pins • One Chute Assembly
• One Product Registration Card
• One Chute Control Rod
Assembly
Handle
1.
Place the shift lever in the roller guides.
raise the upper handle assembly...by tightening the plastic knob located on both the left and right sides of the cables (steering, auger, shift, and drive) are for packaging purposes only. Remove and discard any ...
Operation Manual - Page 8
... will be angled slightly to the one o'clock position. See Fig. 3-4.
4. See Fig. 3-5. Squeeze the trigger on the joystick. silver indicator arrow on the pinion gear below the control
panel faces upward. Insert chute control rod into chute control head as possible, keeping the holes in Fig. 3-6. See Fig. 3-6. See "Top View" in the...
Operation Manual - Page 9
...way into the pinion gear if required. NOTE: The second hole is a reference for Chute Control Rod adjustments. Figure 3-10
Set-Up
Shear Pins
A pair of the engine. Store them in your ...bow tie cotter pins are properly routed through the cable guide on the pinion gear. 6. Insert the chute control rod into the pinion 9. Figure 3-8
7. See Fig. 3-9. See Fig. 3-11. gear.
See ...
Operation Manual - Page 10
... personal injury or damage to the snow thrower and surrounding property.
Assembly & Set-Up To adjust the skid shoes:
1. Chute Clean-Out Tool
The chute clean-out tool is against the ground to... avoid uneven wear on the skid shoes.
3. Adjust them downward, if desired, prior to the desired position. Make certain the entire bottom surface of ...
Operation Manual - Page 11
...snow thrower engine. When the auger control is operating safely and properly. Repeat this several times.
5.
Thread the ferrule without turning the cable onto the "Z" fitting ...Control
Warning! Check the adjustment of the machine.
6. Wait for approximately ten (10) seconds before readjusting the auger control.
7. Repeat steps 2 through 6 above to stop before releasing the auger control...
Operation Manual - Page 12
... speed and direction of the handle panel and is automatically turned on top of travel.
Forward
Your snow thrower has six...Controls and Features
Track Lock Lever Drive Control Shift Lever
Headlight
Chute Assembly Chute Clean Out Tool
4
Chute Directional Control Auger Control
Heated Grips Steering Trigger
Control
Augers
Skid Shoe
Figure 4-1
WARNING! NOTE: Always release the drive control...
Operation Manual - Page 13
... a non-running snow thrower with both controls to Skid Shoe Adjustment on your snow thrower in steering the snow thrower. Refer to stop the augers and the track drive.
Auger Control
The left and right track steering controls are used to engage the track drive. Track Steering Controls
The track drive control is thrown, pivot the joy-stick forward...
Operation Manual - Page 14
...-out tool from the chute assembly.
14
Section 4- While standing in the Engine Operator's Manual. Controls and Features
Normal Snow
Allows the tracks to the rear of the auger housing.
4. Packed Snow
...of the three positions. Shut off engine and remain behind the snow thrower), engage the auger control for hard-packed or icy snow conditions. The chute clean-out tool is used on the rear...
Operation Manual - Page 15
... (R) positions. If the heated grip becomes too hot, turn right. Release it off. Release to turn it and the drive motion will move the switch found on the right handle with your left . See Fig. 5-2. To Steer
With the drive control engaged, squeeze the right steering trigger control to stop .
Engage Heated Grips
To activate the heated...
Operation Manual - Page 16
... carriage bolts and hex nuts which secure it rests on the aluminum drive plate or the rubber friction wheel.
To remove the skid shoes:
1. Maintenance & Adjustments
6
Maintenance
2.
Reassemble the new skid shoes with the four carriage bolts (two on the bottom of operation. 1. NOTE: Tracks removed for clarity
Figure 6-1
To remove...
Operation Manual - Page 17
... speed position. 2.
Tighten the hex nuts on the shift cable index bracket.
Track Tension
Over time the track can stretch. Adjust the track tension as follows (See Fig. 6-6):
Bow-Tie Cotter Pin
Track Side Plate Flange Lock Nut
Figure 6-4
Adjustments
Shift Cable
If the full range of the shaft. Auger Shaft
At least once...
Operation Manual - Page 18
... several times. Chute Directional Control
To adjust the chute control rod, proceed as instructed in a clean, dry area. 4. Reinsert the cotter pin through this section. 3. See Fig. 6-7.
6. It should not roll freely.
3. With the drive control released, push the snow thrower gently forward. The unit should not turn. Engage the drive control and gently attempt to...
Operation Manual - Page 20
Fig. 7-1.
3.
Pivot the idler pulley toward the right. Lift the auger belt from the engine.
2.
Repeat the Auger Control Test on the auger housing.
4. Service 6. To prevent spillage, remove all fuel from the underside of the engine by running engine until the support bracket ...
Operation Manual - Page 23
... to discharge snow
Chute fails to RUN position
4. Chute assembly clogged.
2. Fill tank with fresh clean, gasoline.
3. Move choke control to easily rotate 180 degrees
1. Refer to Maintenance & Adjustments Section.
2. Adjust drive control cable. Adjust auger control cable. Fuel tank empty, or stale fuel. Engine running erratically/ inconsistent RPM (hunting or surging)
Loss of...
Operation Manual - Page 26
...limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to ...as lubricants, filters, blade sharpening, tune-ups, brake adjustments, clutch adjustments, deck adjustments, and normal deterioration of the exterior finish due to ... shall bind Troy-Bilt. Troy-Bilt does not extend any kind be greater than an authorized service dealer. Troy-Bilt does not ...
Similar Questions
Ajust The Tenson On Tracks
how to ajust the tenson on the tracks
how to ajust the tenson on the tracks
(Posted by Anonymous-173263 1 year ago)
Is The Throttle Cable Adjustable On The Troy Bilt Tb225 Tiller? Also What Would
is the throttle cable adustable on the tb225 tiller and also what would make the fuel not stay in th...
is the throttle cable adustable on the tb225 tiller and also what would make the fuel not stay in th...
(Posted by tw285j 1 year ago)
Troy Bilt Horse Garden Tiller
I just bought a Troy Bilt Horse garden tiller. It has an 8 horsepower engine and is probably 10-15 y...
I just bought a Troy Bilt Horse garden tiller. It has an 8 horsepower engine and is probably 10-15 y...
(Posted by jasonrogers1272 3 years ago)
Troy-bilt 31ah64q4711 (2012) Storm 2840 Snowblower Runs Rough & Gas Leak @ Carb
I have a Troy-Bilt 31AH64Q4711 (2012) Storm 2840 Snowblower gas leak @ carb. Removed carb, cleaned t...
I have a Troy-Bilt 31AH64Q4711 (2012) Storm 2840 Snowblower gas leak @ carb. Removed carb, cleaned t...
(Posted by Nborho 6 years ago)
Unit Will Not Start
Unit worked fine until last winter when it would not start, either using the electric starter or the...
Unit worked fine until last winter when it would not start, either using the electric starter or the...
(Posted by rkferguson 7 years ago)