Troy-Bilt Storm Tracker 2690 Support Question
Troy-Bilt Storm Tracker 2690 Support Question
Find answers below for this question about Troy-Bilt Storm Tracker 2690.Need a Troy-Bilt Storm Tracker 2690 manual? We have 1 online manual for this item!
Question posted by rkferguson on October 17th, 2016
Unit Will Not Start
Unit worked fine until last winter when it would not start, either using the electric starter or the manual pull-string. Spark plug looks clean, can smell gas, engine turns over but wont' start.
Current Answers
Answer #1: Posted by Odin on October 17th, 2016 4:21 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
See this manual page: https://www.manualslib.com/manual/484345/Troy-Bilt-Storm-Tracker-2690xp.html?page=23&term=troubleshooting&selected=2. Your issue is the first listed, on top.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt Storm Tracker 2690 Manual Pages
Operation Manual - Page 1
BOX 361131 CLEVELAND, OHIO 44136-0019
Form No. 769-07126 (May 02, 2011) Storm Tracker 2690XP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
Printed In USA
TROY-BILT LLC, P.O.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Safe Operation ...
Operation Manual - Page 2
... to Troy-Bilt LLC • P.O. Please refer to the engine manufacturer's Owner's/Operator's Manual, packed separately with regards to the right. You can locate the model plate by standing at the operator's position and looking down at (800) 828-5500 or (330) 558-7220 ◊ Write to familiarize yourself with a local authorized service...
Operation Manual - Page 3
... in this manual before attempting to be used. Never attempt...manual in a safe place for future and regular reference and for all doormats, newspapers, sleds, boards, wires and other reproductive harm. Do not wear jewelry, long scarves or other loose clothing, which , if not followed,
could result in moving parts. Let engine and machine adjust to comply with electric start engines...
Operation Manual - Page 4
...starting the engine.
13. If possible, remove gas-powered equipment from a
leave the operating position (behind and use extreme care in the discharge or collector openings. Never put hands or feet near rotating parts, in front of your vehicle
the engine, disconnect the spark plug... and pets or
f. Never operate this manual, use the clean-out tool provided to a complete stop before...
Operation Manual - Page 5
...), this manual.
2. Never tamper with a spark arrestor meeting applicable local or state laws (if any unimproved forest-covered, brush covered or grass-covered land unless the engine's exhaust system is used on regular unleaded gasoline, and may have stopped rotating.
3. If a spark arrestor is equipped with factory setting of the engine.
5. Section 2 -
Before cleaning, repairing...
Operation Manual - Page 6
... in the rain
WARNING- ROTATING AUGER Do not put hands or feet near rotating parts, in a poorly ventilated area.
Your Responsibility-Restrict the use the engine's electric starter in the manual(s) before touching.
Engine exhaust contains carbon monoxide, an odorless and deadly gas. Allow engine and muffler to persons who read, understand and follow all instructions on this...
Operation Manual - Page 7
Looking beneath the handle panel, check that all of the upper handle; Chute Assembly
1.
Chute Chute Base
Figure 3-3... located on both the left and right sides of Crate
• One Snow Thrower
• One Snow Thrower Operator's Manual
• One Engine Manual
• Two Replacement Auger Shear Pins • One Chute Assembly
• One Product Registration Card
• One Chute...
Operation Manual - Page 9
... up with the indicator arrow on the pinion gear, and will fit snuggly into the pinion gear. removed in the manual bag. Support the rear of the engine. NOTE: The hole is used to chute support
joystick.
NOTE: The second hole is a reference for Chute Control Rod adjustments. Store them in your snow...
Operation Manual - Page 10
... snow removal on a smooth surface, raise the skid shoes higher on each side) and carriage bolts. Use a middle or lower position when the area to be cleared is against the ground to avoid uneven wear..., causing personal injury or damage to the snow thrower and surrounding property. Chute Clean-Out Tool
The chute clean-out tool is not recommended that you choose to operate the snow thrower on ...
Operation Manual - Page 11
...jam nut against the ferrule. Thread the ferrule without turning the cable onto the "Z" fitting until there is ...Manual. With the throttle control in the FAST (rabbit) position and the auger control in the disengaged "up " position, walk to verify proper adjustment has been achieved. Assembly & Set-Up
11 Auger Control
Warning! In a well-ventilated area, start the snow thrower engine...
Operation Manual - Page 12
... the machine and in this manual before changing speeds. It can... Caution: It is started. Read, understand, and follow ...Clean Out Tool
4
Chute Directional Control Auger Control
Heated Grips Steering Trigger
Control
Augers
Skid Shoe
Figure 4-1
WARNING! To turn...turned on top of travel. The headlight is located on when the engine is recommended that you wear gloves when using the heated grip.
Operation Manual - Page 13
... with these controls. Squeeze the right track control when turning right, squeeze the left control when turning left .
• To change the direction in simultaneously...Shoe Adjustment on the left and right track steering controls are used to assist in open areas until you can be adjusted by... augers and start snow throwing action.
Chute Directional Control
The auger control is thrown, ...
Operation Manual - Page 14
... 4- The chute clean-out tool is used on the rear of the auger housing, reinsert the key and start the snow thrower's engine as instructed in the operator's position (behind handles until all moving parts have stopped before unclogging.
Release both the Auger Control and the Drive Control.
2. While standing in the Engine Operator's Manual. Move...
Operation Manual - Page 15
... lock lever to the right, then forward or backward to turn it and the drive motion will move the switch found on starting and stopping the engine. Caution: It is recommended that you are comfortable with.
2. Operation
5
Starting and Stopping the Engine
Refer to the Engine Operator's Manual packed with your right hand. Select a speed appropriate for...
Operation Manual - Page 16
... attach it rests on each side) and hex flange nuts. Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of engine oil (or 3-in-1 oil) to use the other edge.
NOTE: Augers not shown for clarity
Figure 6-2
3. Engine
Refer to Fig. 6-1. Refer to the Engine Operator's Manual. Maintenance & Adjustments
6
Maintenance
2.
Operation Manual - Page 17
... of the snow thrower.
2. Skid Shoes
Refer to the Assembly and Set-up section for instructions on the shift cable index bracket. See
Fig. 6-5. This pulls the "J" bolts attached to take up section for instructions on the front track idler wheels.
Place the shift lever in the cable. 4. Loosen the hex...
Operation Manual - Page 18
...or clockwise to the Engine Operator's Manual for 30 days or longer, follow the storage instructions below. 1. The unit should not turn. See Fig. ...used for information on the chute rotation assembly. 2. Proceed as follows: 1.
Maintenance & Adjustments Shut off the engine as follows:
1. Loosen the hex jam nut on the ferrule with the second hole in a clean, dry area. 4. Clean...
Operation Manual - Page 19
.... 7-2.
Tip the snow thrower up and forward so that it .
If changing just one .
See Fig. 7-3.
Remove the frame cover from the engine. Do not attempt to avoid unintended starting.
2. Remove the key to pour fuel from the underside of the other belt.
1. Figure 7-1 3. Auger Belt
NOTE: It is out of the...
Operation Manual - Page 23
.... Engine running on engine. 6. Faulty spark plug. 5.
Snow Thrower fails to propel itself
Snow Thrower fails to discharge snow
Chute fails to start
Cause
1. Friction wheel worn. 1. Fuel becomes stale after thirty days.
2. Choke not in need of adjustment. 2. Primer button not being used properly. 1. Auger control cable in the RUN position. 4. Fill tank with clean-out...
Operation Manual - Page 26
...attachment not approved by Troy-Bilt for use with respect to new merchandise purchased and used in the United States and/or its option, repair or...purchased as mentioned above as to the parts as set forth in this manual will , at P.O.
MANUFACTURER'S LIMITED WARRANTY FOR
The limited warranty set forth...lawn care services or for rental expenses to our Web site at www....
Similar Questions
Ajust The Tenson On Tracks
how to ajust the tenson on the tracks
how to ajust the tenson on the tracks
(Posted by Anonymous-173263 1 year ago)
Not Starting
I changed oil and replaced spark plug but it will not start I also forgot to drain out old fuel so I...
I changed oil and replaced spark plug but it will not start I also forgot to drain out old fuel so I...
(Posted by Joepupi 3 years ago)
Troy Bilt Cs 4265
Could not start engine, replaced spark plug, started for 1 minute only after spread starter, and sto...
Could not start engine, replaced spark plug, started for 1 minute only after spread starter, and sto...
(Posted by fangchlee 7 years ago)
How To Adjust
the tension on the steering trigger control for faster turns on the troy Bilt storm tracker 2690XP h...
the tension on the steering trigger control for faster turns on the troy Bilt storm tracker 2690XP h...
(Posted by jamess8007 7 years ago)