Ryobi BD4600 Support Question

Find answers below for this question about Ryobi BD4600.
Need a Ryobi BD4600 manual? We have 1 online manual for this item!

Ryobi Overview Questions Manuals Reviews Videos Research

Question posted by bluegums2011 on June 17th, 2020

Re-connect On/off Switch, Coil And Motor On Ryobi Bds4600

I've got a Bds4600 Ryobi belt/disc sander. The wiring was disconnected to replace the starter /cap but no notice was taken as to where the wiring was. I just need to know how to replace the wiring? Which wire goes on which spade connector?Thanks Dave

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by hzplj9 on June 17th, 2020 9:33 AM

This answer was accepted by the poster of the original question.

hzplj9

Member since:
June 25th, 2012

Points: 4,874,710

1,100
points

Download the repair sheet from here:

https://www.manualslib.com/manual/551467/Ryobi-Bd4601.html

Page 5 gives all the info.

Hope that helps.

Related Ryobi BD4600 Manual Pages

English Manual - Page 1

..., the user must read and understand the operator's manual before using this product. WARNING: To reduce the risk of rugged, trouble-free performance. OPERATOR'S MANUAL Belt/disc sander BD4600 4 x36 Your belt/disc sander has been engineered and manufactured to our high standard for your purchase.

English Manual - Page 2

...RYOBI® power tool which does not work properly due to defective workmanship or materials by other than those specifically stated in this warranty. HOW TO GET SERVICE: Just return the power tool...fitness for a period of two years from state to www. warranty RYOBI® POWER TOOL - To receive a replacement power tool or requested warranty service, you may not apply to you by ...

English Manual - Page 3

... carry the current your hand and frees both hands to disconnect from work into moving parts, breakage of parts, mounting and any tool.  USE RECOMMENDED ACCESSORIES. Use only a cord heavy enough to do not connect the equipment-grounding conductor to a live terminal. A wire gauge size (A.W.G.) of cord location and keep it is off...

English Manual - Page 4

... alert! NEVER leave the tool unattended while connected to a power source.  Support workpiece with sander or workpiece before connecting to see the work surface.  NEVER sand more than one workpiece on the sander table at a time. GENERAL SAFETY RULES  Inspect EXTENSION CORDS periodically and replace if damaged.  Keep TOOL dry, clean, and free...

English Manual - Page 5

... surface speed, orbits etc., per minute Wet Conditions Alert Do not expose to turn the belt/disc sander ON or OFF. SYMBOLS Some of the following symbols may be used on this product. Always... with side shields and, as necessary, a full face shield when operating this tool. Failure to operate the tool better and safer. Read The Operator's Manual Eye Protection Safety Alert No Hands ...

English Manual - Page 6

... are intended to explain the levels of any power tool can result in death or serious injury. Call Ryobi customer service for assistance. SAVE THESE INSTRUCTIONS Before beginning power tool operation, always wear safety goggles or safety glasses with this product. Always use only identical replacement parts. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently...

English Manual - Page 7

... 10 - **Used on 12 gauge - 20 amp circuit. If damaged replace immediately. SPEED AND WIRING The belt speed of least resistance for lights cannot properly carry a power tool motor. This speed is powered by a qualified electrician. For voltage, the wiring in a shop is approximately 1,900 SFM. Wire that is green with lower voltage. A line that accept the...

English Manual - Page 8

... guide for narrow ripping operations. Workpiece or Material The item on which a blade or cutting tool is designed to the blade other aids. Worktable Surface where the workpiece rests while performing a ...the operator's hands well away from being guided by the workpiece being dropped into the tool first. Resin A sticky, sap-based substance that the tip of the blade. Set...

English Manual - Page 9

.... WORK SUPPORT 4 x36 TRACKING KNOB BELT TENSION LEVER SANDING BELT WORKTABle MITER GAUGE BEVEL GAUGE SWITCH AND switch KEY SANDING DISC horizontal and vertical position holes Fig. 2 Know Your BELT/DISC SANDER See Figure 2. switch and switch key Your belt/disc sander has an easy access power switch. WORK SUPPORT Supports the workpiece on the tool and in this product, familiarize...

English Manual - Page 10

... is intended to turn the belt/disc sander ON or OFF. n Remove the switch key from the power supply and the switch is equipped with the belt before plugging tool into the switch, lift the switch button to start the tool. The belt/disc sander is in serious personal injury. TO TURN THE BELT/DISC SANDER OFF:  Press the switch button down to prevent unauthorized...

English Manual - Page 11

... items are included with this tool until the parts are replaced. n Carefully remove the tool and any parts are damaged or missing do not operate this tool. n If any accessories from the box. Failure to power supply until you have carefully inspected and satisfactorily operated the tool. WARNING: Do not connect to comply could result in...

English Manual - Page 12

... WORKTABLE Fig. 8 WORKTABLE Fig. 9 installing/REPLACING sanding belt See Figure 7. On the smooth side of sanding disc with the belt sander See Figure 9. n Unplug the belt/disc sander. n Unplug the belt/disc sander. n Using the two phillips head screws, securely tighten the disc guard into position. n Unplug the belt/disc sander. mounting the worktable for use with...

English Manual - Page 13

... tool, it to a workbench, holes should be drilled through holes in the base as a template for hole pattern. n Drill holes through holes in belt/disc sander, the material being mounted to a workbench or other stable surface. Mounting belt/DISC sander to workbench See Figure 12. clamping belt/DISC sander to workbench See Figure 11. When mounting the belt/disc sander to...

English Manual - Page 14

.... SANDING SMALL END SURFACES USING THE MITER GAUGE See Figure 14. OPERATION WARNING: Do not allow familiarity with tools to heed this warning could result in serious personal injury. Remember that a careless fraction of the sanding disc could cause the workpiece to 45° for sanding small end surfaces on the sanding...

English Manual - Page 15

... shown in figure 18. SANDING CURVED PIECES See Figures 17 - 18. The belt/disc sander can be adjusted using the sanding disc and moving work support can sand both vertically and horizontally. Loosen the screws by turning them counterclockwise. n Move the sanding belt into the holes in serious personal injury. n Hold the workpiece firmly, keeping...

English Manual - Page 16

... WARNING: Before performing any adjustment, make sure the tool is unplugged from the disc, turn the tracking knob counterclockwise 1/4 turn. Failure to heed this warning could result in belt/disc sander. If the belt tends to the sanding DISC See Figure 20. n Turn the switch ON and then immediately OFF again, noting belt movement. Readjust tracking knob if necessary.

English Manual - Page 17

... there is extremely important to fail prematurely and make a severe chattering noise. n Tighten the belt tension nut securely. Tighten securely. n Replace the motor cover with plastic parts. Electric tools used on the motor pulley. LUBRICATION All of give. n Unplug the belt/disc sander. n Using a phillips head screwdriver, remove the two screws in serious personal injury. Raising...

English Manual - Page 18

... information: • MODEL NUMBER • SERIAL NUMBER BD4600 Ryobi® is a registered trademark of work with approved safety equipment, such as those dust masks that are : • lead from lead-based paints, • crystalline silica from bricks and cement and other reproductive harm. OPERATOR'S MANUAL Belt/disc sander BD4600 WARNING: Some dust created by power sanding...