Ryobi BD4600 Support Question
Ryobi BD4600 Support Question
Find answers below for this question about Ryobi BD4600.Need a Ryobi BD4600 manual? We have 1 online manual for this item!
Question posted by rdley on February 7th, 2013
Bd4600 Belt Sander Switch
I have had to replace the Starter switch and did take note of the wiring
Current Answers
Related Ryobi BD4600 Manual Pages
English Manual - Page 1
SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATOR'S MANUAL
Belt/disc sander
BD4600
4 x36
Your belt/disc sander has been engineered and manufactured to our high standard for , it will give you for your purchase.
WARNING: To reduce the risk of operation, and ...
English Manual - Page 2
... or less. One World Technologies, Inc. Box 1207, Anderson, SC 29622-1207, by calling 1-800-525-2579 or by other than Authorized Service Centers. The replacement power tool will repair any faulty workmanship, and either request service under normal usage and does not cover any charge to you . warranty
RYOBI® POWER...
English Manual - Page 3
... tool is necessary, do not connect the equipment-grounding conductor to follow all tools should be properly repaired or replaced ...and perform its operation. A wire gauge size (A.W.G.) of the motor could occur if the tool is in any other part...switch is the equipment-grounding conductor. The use the next heavier gauge. Feed work area. Never carry tool by removing starter keys. ...
English Manual - Page 4
...between worktable and sanding belt or disc.
avoid kickback by sanding in . Do not allow familiarity (gained from frequent use them these instructions. Have defective switches replaced by an authorized ...ALL SETUPS. Refer to them frequently and use of your sander) to right against the direction the drum sleeve is torn from your tool to a workbench or table at a time.
...
English Manual - Page 5
... Precautions that involve your safety. Do not reach across the sanding disc to turn the belt/disc sander ON or OFF. SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
...result in damp locations.
Proper interpretation of the following symbols may be used on this tool.
To reduce the risk of current Rotational speed, at no load
Class II Construction
...
English Manual - Page 6
..., do not use over eyeglasses or standard safety glasses with ANSI Z87.1. Always use only identical replacement parts. SYMBOLS
The following signal words and meanings are intended to explain the levels of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage...
English Manual - Page 7
...determine the minimum wire size required in a shop is powered by a precision-built electric motor. If damaged replace immediately. Never use tool with the tool outdoors, use . For voltage, the wiring in an ... to a power supply that is designed for use . NOTE: AWG = American Wire Gauge
When working area. Before using a power tool at a considerable distance from the power source, use an...
English Manual - Page 8
... angle other than at 90°. Workpiece or Material The item on which a blade or cutting tool is mounted. Worktable Surface where the workpiece rests while performing a cutting, drilling, planing, or sanding...extend completely through cut or the slot produced by the workpiece being dropped into the tool first. Push Blocks (for table saws) Devices used for drilling large holes accurately....
English Manual - Page 9
... of the project you are used for easy belt replacement. Before use of this product requires an understanding of the belt from horizontal to vertical providing different positions for ...sanding disc is located on the sanding belt.
FEATURES
PRODUCT SPECIFICATIONS
Belt Size 4 in . switch and switch key
Your belt/disc sander has an easy access power switch.
Table Tilt 0°- 45°...
English Manual - Page 10
... with the sanding disc can result in locking feature. Contact with a power switch that has a built-in serious personal injury.
The belt/disc sander is in contact with the belt before plugging tool into the switch, lift the switch
button to turn the belt/disc sander ON or OFF. WARNING:
In the event of accidental starting when power returns...
English Manual - Page 11
...replaced. Failure to modify this warning could result in a hazardous condition leading to power supply until you have carefully inspected and satisfactorily operated the tool. WARNING:
Do not attempt to heed this tool...The following items are damaged or missing, please call 1-800-525-2579 for use with the tool:
n Sanding Disc n Disc Guard n Phillips Screws (2) n Socket Head Screws, M8 x...
English Manual - Page 12
... the worktable no farther than 1/16 in figure 6. The sanding belt must run in the direction of sanding disc with the belt sander
See Figure 9. mounting the worktable for use with plate and press firmly
into the hole as shown in . installing/REPLACING sanding belt
See Figure 7. from the
sanding surface. Drive roller
HEX set...
English Manual - Page 13
....
thickness is to , and the lock washers and hex nuts. If machine bolts are used as a portable tool, it is to a workbench or other stable surface. Mounting belt/DISC sander to workbench
See Figure 12. NOTE: All bolts should be inserted from the underside of the workbench.
n Mark holes on workbench aligning holes in...
English Manual - Page 14
... in serious personal injury. n Set worktable to do so could cause the workpiece to heed this tool for bevel sanding. Position the worktable
no farther than 1/16 in . A miter gauge is sufficient...SANDING SMALL END SURFACES USING THE MITER GAUGE
See Figure 14. BEVEL SANDING
See Figure 13. NOTE: Always move the workpiece across the sanding disc from the sanding surface. from the left side ...
English Manual - Page 15
The belt/disc sander can be used with the sanding belt in figure 17.
NOTE: Sand long workpieces with either the horizontal or vertical sanding operation.
Apply only enough pressure to allow the sanding belt to fly up. Sanding inside curves on the sanding belt:
Always sand inside curves on the idler drum as shown in the...
English Manual - Page 16
...belt/disc sander. n Turn the switch ON and then immediately OFF again,
noting belt movement. NOTE: Use the adjustment screws beneath the worktable to move the table further or closer to the sanding disc and retighten
the table lock knob. To check belt tracking: n Turn the switch... the belt is not tracking properly. adjustments
WARNING:
Before performing any adjustment, make sure the tool is ...
English Manual - Page 17
... of the bearings in . Tighten securely. NOTE: Excessive tightness on the drive belt may be damaged by squeezing the belt with any maintenance or adjustment. n Adjust the motor bracket so that could cause possible serious personal injury, turn off the tool, remove the switch key, and unplug the belt sander before performing any of these types of...
English Manual - Page 18
... to filter out microscopic particles.
• SERVICE
Now that you have purchased your tool, should a need ever exist for a complete list of work with approved safety equipment... these exposures varies, depending on a plate attached to the motor housing. OPERATOR'S MANUAL
Belt/disc sander
BD4600
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction...
Similar Questions
Owners Manual
I'm trying to find an owners manual for the BD4600 bench belt sander.
I'm trying to find an owners manual for the BD4600 bench belt sander.
(Posted by a1gyrine 2 years ago)
Re-connect On/off Switch, Coil And Motor On Ryobi Bds4600
I've got a Bds4600 Ryobi belt/disc sander. The wiring was disconnected to replace the starter /cap b...
I've got a Bds4600 Ryobi belt/disc sander. The wiring was disconnected to replace the starter /cap b...
(Posted by bluegums2011 3 years ago)
Ryobi Bd4600 Belt And Disk Sander
Put new bearing in motor, reasembaled complete belt disk sander, checked wiring with diagram turn sw...
Put new bearing in motor, reasembaled complete belt disk sander, checked wiring with diagram turn sw...
(Posted by willie4barbp 7 years ago)
What Wires Go To Switch And Reset On10 Inch Ryobi Table Saw
My saw stop working I took the cover off the svitch I notice the reset switch was not wired and ther...
My saw stop working I took the cover off the svitch I notice the reset switch was not wired and ther...
(Posted by Merle1954sm 9 years ago)
Hpl50 Hand Plainer
why Is It That Ryobi Does Not Stand Up To The Tools They Make? i Needed Or Need belts For This To...
why Is It That Ryobi Does Not Stand Up To The Tools They Make? i Needed Or Need belts For This To...
(Posted by JERRYMOUTON 11 years ago)