Ryobi BD4600 Support Question
Ryobi BD4600 Support Question
Find answers below for this question about Ryobi BD4600.Need a Ryobi BD4600 manual? We have 1 online manual for this item!
Question posted by willie4barbp on May 4th, 2016
Ryobi Bd4600 Belt And Disk Sander
Put new bearing in motor, reasembaled complete belt disk sander, checked wiring with diagram turn switch on motor runs backwards? why?
Current Answers
Related Ryobi BD4600 Manual Pages
English Manual - Page 1
... rugged, trouble-free performance. SAVE THIS MANUAL FOR FUTURE REFERENCE
When properly cared for dependability, ease of operation, and operator safety. OPERATOR'S MANUAL
Belt/disc sander
BD4600
4 x36
Your belt/disc sander has been engineered and manufactured to our high standard for , it will give you for your purchase. Thank you years of injury, the...
English Manual - Page 2
... complete the work properly due to defective workmanship or materials by the limited warranty for the balance of the two year period from state to state.
warranty
RYOBI® POWER TOOL - TABLE OF CONTENTS
Introduction...2 Warranty...2 General Safety Rules...3-4 Specific Safety Rules...4 Symbols...5-6 ...
English Manual - Page 3
...; DON'T FORCE THE TOOL. Be sure switch is the equipment-grounding ...motor could occur if the tool is recommended for which it to follow all times.
MAINTAIN TOOLS WITH CARE. Do not force the tool or attachment to a complete stop.
PROTECT YOUR LUNGS. If in use the next heavier gauge. Follow instructions for alignment of moving parts, binding of moving parts. Check...
English Manual - Page 4
... belt ...CHECK ALL SETUPS. Have defective switches replaced by hand.
Use extra supports (tables, saw horses, blocks, etc.) for any solvents to clean tool...sander table at a time. Do not stack more than one piece at a time.
Always feed workpiece from oil and grease. Never use a clean cloth when cleaning.
Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN...
English Manual - Page 5
... Symbol Hot Surface
To reduce the risk of the following symbols may be used on this tool. Failure to rain or use in serious personal injury. Contact with any hot surface.
...tool better and safer.
To reduce the risk of these symbols will allow you to keep your safety.
Please study them and learn their meaning. Do not reach across the sanding disc to turn the belt/disc sander...
English Manual - Page 6
...service technician. Always use this product until you read thoroughly and understand completely the operator's manual. Call Ryobi customer service for repair. WARNING:
Indicates a potentially hazardous situation, which ... Vision Safety Mask for use only identical replacement parts. Before beginning power tool operation, always wear safety goggles or safety glasses with this product. SAVE...
English Manual - Page 7
...built electric motor.
The ...AND WIRING
The belt speed of this tool on...wires and cut or worn insulation. Wire that the tool will be plugged into an outlet, double check...Wire Size (A.W.G.)
25' 16
16 16 16 14
14
50' 16
16 16 14 14
12
100' 16
16
14 12 10
-
**Used on lumber, tools or other obstructions while you are not completely understood, or if in accordance with the tool...
English Manual - Page 8
... saw blade tooth is bent (or set) outward from a block so the end (or part of turns completed by a spinning object in a workpiece that the tip of a workpiece by the blade.
A push... with both a miter and a bevel angle.
Arbor The shaft on which a blade or cutting tool is angled rather than 90°.
Push Blocks (for jointer planers) Device used for drilling large holes...
English Manual - Page 9
... of the information on the tool and in this product, familiarize yourself with all operating features and safety rules. SANDING BELT
The sanding belt can be adjusted from horizontal to 45°.
Disc Speed 3,600 r/min. (RPM)
Table Size 8-1/2 in .
switch and switch key
Your belt/disc sander has an easy access power switch.
x 36 in . Before use...
English Manual - Page 10
... operator and result in use by children and others.
n Place the switch in locking feature. The belt/disc sander is in contact with the belt before plugging tool into the switch, lift the switch
button to start the tool. TO TURN THE BELT/DISC SANDER ON: With the switch key inserted into the power source. Store
key in serious personal injury...
English Manual - Page 11
...discard the packing material until the parts are damaged or missing, please call 1-800-525-2579 for use with the tool:
n Sanding Disc n Disc Guard n Phillips Screws (2) n Socket Head Screws, M8 x 12 (2) n ...complete. WARNING:
Do not connect to make sure no breakage or damage occurred during shipping. n Carefully remove the tool and any parts are damaged or missing do not operate this tool...
English Manual - Page 12
... 8. use extreme caution when pushing the tension lever back into the hole as shown in figure 9.
The sanding belt must run in the direction of the
disc, aligning holes as shown in . n Unplug the belt/disc sander. n Insert the index pin into place. n Using a hex key, tighten the hex set screw
12
4 x36
sanding...
English Manual - Page 13
... easily be mounted using holes in a permanent location, it permanently to a workbench, holes should be inserted from the underside of the tool housing. n Mark holes on board where belt/disc sander is recommended. If the belt/disc sander is to be used in the base as a template for hole pattern. n Mark holes on workbench where...
English Manual - Page 14
... objects being thrown into your eyes resulting in . OPERATION
WARNING:
Do not allow familiarity with side shields when operating power tools. APPLICATIONS
You may use any attachments or accessories not recommended by turning it clockwise. NOTE: Always move the workpiece across the sanding disc from the left side toward the center.
4 x36...
English Manual - Page 15
... center as shown in the pulley cover. n Lock the sanding belt by turning them counterclockwise. NOTE: Use extra caution when sanding very thin pieces and apply only enough ... vertical position by moving the work evenly across the sanding belt. OPERATION
HORIZONTAL AND VERTICAL SANDING
See Figure 15. The belt/disc sander can be adjusted using the sanding disc and moving work ...
English Manual - Page 16
... result in serious personal injury. adjustments
WARNING:
Before performing any adjustment, make sure the tool is unplugged from the disc, turn the
tracking knob counterclockwise 1/4 turn.
n Turn the switch ON and then immediately OFF again,
noting belt movement.
n Using a combination square, check the angle of the
worktable with the disc, loosen the table
lock knob and tilt...
English Manual - Page 17
... life of the bearings in
the center of give. Raising the motor
pulley releases the belt tension. WARNING:
Do not at any maintenance or adjustment. GENERAL MAINTENANCE
Avoid using compressed air. n Adjust the motor bracket so that could cause possible serious personal injury, turn off the tool, remove the switch key, and unplug the belt sander before performing any...
English Manual - Page 18
...check...-treated lumber.
OPERATOR'S MANUAL
Belt/disc sander
BD4600
WARNING:
Some dust created by...tool, should a need ever exist for a complete list of this tool... will be found on how often you call 1-800-525-2579 for your nearest Authorized Service Center. Some examples of Ryobi...BD4600
Ryobi® is a registered trademark of these exposures varies, depending...
Similar Questions
Need New Compressor Motor
Where can I get a compressor? The compressor side stopped working.
Where can I get a compressor? The compressor side stopped working.
(Posted by edoak 1 year ago)
Re-connect On/off Switch, Coil And Motor On Ryobi Bds4600
I've got a Bds4600 Ryobi belt/disc sander. The wiring was disconnected to replace the starter /cap b...
I've got a Bds4600 Ryobi belt/disc sander. The wiring was disconnected to replace the starter /cap b...
(Posted by bluegums2011 3 years ago)
Bd4600 Belt Sander Switch
I have had to replace the Starter switch and did take note of the wiring
I have had to replace the Starter switch and did take note of the wiring
(Posted by rdley 11 years ago)
Serial Number
I can't find a separate serial number for my belt/disc sander. Is it just the same as the model numb...
I can't find a separate serial number for my belt/disc sander. Is it just the same as the model numb...
(Posted by eastonfam 11 years ago)
Bought New Orbital Jig Saw Today, Using A While, Now Won't Turn On
bought today, used it several times. tried to turn it on now, won't come on. tried several diffe...
bought today, used it several times. tried to turn it on now, won't come on. tried several diffe...
(Posted by nmotb 12 years ago)