Rheem P-M406 Support Question
Rheem P-M406 Support Question
Find answers below for this question about Rheem P-M406.Need a Rheem P-M406 manual? We have 3 online manuals for this item!
Question posted by Anonymous-162298 on April 16th, 2017
What Does This Mean
What does Rollout SW open mean
Current Answers
Answer #1: Posted by Odin on April 16th, 2017 12:50 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
That's the rollout switch. See https://www.manualslib.com/manual/600793/Rheem-P-M206.html?page=35&term=rollout. Rheem's instructions are to "check for blocked heat exchanger and soot."
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Rheem P-M406 Manual Pages
Brochure - Page 2
... Light Off
The soft-opening gas valve ensures smooth turn-on -board diagnostic controls that tend to keep the Rheem Digital operating even in outdoor installations with the heater at your preferred set your
pool and spa temperature precisely at all times.
Even the smallest details, such as the studs and nuts, are...
Brochure - Page 3
...to make changes without notice.
All sizes are capable of your ability to maintain the pool or spa water chemistry, a cupro-nickel heat exchanger is a cost-effective way to protect against ...Rheem reserves the right to last with an optional cupro-nickel fin tube heat exchanger for pool and spa heater heat exchangers, where the water chemistry is properly maintained. The D-2 Power Vent is...
Operating Instructions - Page 1
...; Do not try to the heater or in your building. • Immediately call your gas supplier, call the fire department.
INSTALLATION & OPERATING INSTRUCTIONS
Gas-Fired Pool & Spa Heater
Atmospheric Models 206A, 266A, 336A & 406A
Lo NOx Models 207A, 267A, 337A & 407A
WARNING: If these instructions are not followed exactly, a fire or explosion...
Operating Instructions - Page 2
...**
* Free Chlorine MUST NOT EXCEED 5 PPM! ** In salt water chlorinated pools, the total TDS can damage your heater, and which is not covered under ...Pools Fiberglass Spas
Other Pool & Spa Types
Water Temp. (Deg. WATER CHEMISTRY (Corrosive water voids all warranties)
For your health and the protection of the pool or spa water should be obtained from your pool or spa builder, accredited pool...
Operating Instructions - Page 3
... 3
37 2-Wire Remote Control
MAINTENANCE & CARE PROCEDURES
37 3-Wire Remote Control
8
Pool & Spa Water Chemistry
38 Time Clock / Fireman's Switch
8
Automatic Chlorinators & Chemical Feeders 38...Pressure Switch
9
Cold Weather Operation
38 Flame Roll-Out Safety Switch
9
Winterizing the Pool & Spa Heater
38 High Limits
10 PART TWO
39 Pilot Safety
INSTALLATION & SERVICE INSTRUCTIONS ...
Operating Instructions - Page 4
... toggle switch to turn the heater On or Off and adjust the temperature settings for the pool or spa. Keep heater area clear and free from 65°F (18°C) to turn the... dust, lint and debris. SECTION 1 - See figure above for location of safe and reliable pool/spa water heating. The temperature range is filled with millivolt or electronic ignition.
WATER
Water must be ...
Operating Instructions - Page 7
... on pg. 38 of the pilot and burner. Drinking of alcoholic beverages before using pools or hot tubs.
6. Pregnant women should not be hazardous. Persons taking medications which could... deformed child. MILLIVOLT PILOT BURNER FLAME
A yellow or "floating" flame indicates restricted air openings or incorrect orifice size. spa or hot tub thermostats may err in the birth of 100°F (38°C)...
Operating Instructions - Page 8
...into the pool or spa water before being circulated through the heater. On indoor heaters, clean room intake openings to run at its prime and be higher than usual).
4. POOL & SPA WATER CHEMISTRY...device to your "circuit breaker" has tripped. Low flame means low gas pressure. Keep area around finned tubes and "V" baffles, and open flue gas passageways. Such damage is broken). DO NOT ...
Operating Instructions - Page 9
...heat exchanger inspection panel on the return header. When starting the heater with pool water below 50°F is not warranted against freeze-ups. The heater is...heater for freeze protection. Open drain plug on the inlet/outlet header, (under water pipes). When temperatures are reached.
COLD WEATHER OPERATION
WINTERIZING THE POOL & SPA HEATER
IMPORTANT FREEZE INFORMATION
...
Operating Instructions - Page 10
... AND SERVICE INSTRUCTIONS
SECTION 1 - Remove the heater from the carton.
"Pagoda" top
1. Pressure relief valve
7. 2" CPVC adapters (2)
8. can also be reviewed thoroughly before installing your pool/spa heater. "Pagoda" top
2. 2" CPVC union with the heater:
STANDARD UNIT (POLYMER HEADERS)
ASME UNIT (CAST IRON HEADERS)
1.
Plastic pipe finish flange for gas line...
Operating Instructions - Page 23
...warmer than two horsepower will exceed this heater. If pipe is 125 psi.
if cold, open bypass. No shut-off valve shall be necessary to local building codes, it may be... tripped at the heater. From Heater To Heater
CAST IRON HEADER
PRV
(ASME MODELS)
To Pool/ Spa
From Pool/ Spa
AUXILIARY BYPASS VALVE (DO NOT USE GATE VALVE)
AUXILIARY BYPASS VALVE ADJUSTMENT
To set bypass: ...
Operating Instructions - Page 24
... 3. CAUTION: An additional source of the heater is plumbed to the return line to the pool or spa must not have any water leaks will not damage the structure of the filter pump. Be advised... fire. PVC pipe may be down stream of the filter is operating. The outlet side of the pool heater). a solar system, must be glued directly into header unions (Standard models only).
24 The pump...
Operating Instructions - Page 32
... The knob stop ring to not damage controls
or wiring.
Do
not force. SPA TEMPERATURE RANGE
POOL TEMPERATURE RANGE
2. NOTE: Caution must be used to the desired location and re...
Rotate control panel down until panel stops.
KNURLED SCREW
The thermostat is fitted with a means of control panel. 3. CONTROL ADJUSTMENTS ADVANCED FLAME TECHNOLOGY (AFT) MODELS
Temp Adjust Buttons
Mode...
Operating Instructions - Page 33
... hours of the faults begins with "Heating." The heater will also be displayed and may require service. The LCD display window indicates the mode (OFF, SPA, POOL) and the actual water temperature.
FLAME STRENGTH INDICATOR
Press the DOWN button.
ALTERNATING DISPLAYS DURING HEATING Service Menu and Fault History To access the Service...
Operating Instructions - Page 34
... will change the Maximum Temperature Setting to 65°F (18.5°C) and the POOL and SPA maximum temperature settings will revert back to your desired value. Successfully unlocking the control ... to access the program screen. This will display "Lockout Cleared." NOTE: Both the POOL and SPA setpoints will be programmed. Press the Mode button until Set Factory Defaults appears on the...
Operating Instructions - Page 35
... valves are displayed in Pool, Spa and Remote modes.
Fault
manded state. LoNox Tab Fault
Voltage is a demand for heat present.
EEPROM Fault
Clock/ Fireman Sw
Low Temp Lockout
Memory fault, reset set points, replace board if fault does not clear. Display
Water Sw Open
Condition
Water pressure switch open . Vent/Field Sw #1
Vent spill switch/field...
Operating Instructions - Page 36
... a two- When connecting the heater to a remote system, identify whether it only provides a switching function to the heater enclosure for 3 to select the desired pool or spa temperature.
This damage can be limited if the service person discharges himself, following : The digital thermostat model is supplying its own voltage to the heater...
Operating Instructions - Page 37
...For a 2-Wire Remote Control from a remote without its own sensor, push the mode button "POOL" or "SPA"
mode and set the temperature to 2.5 in a separate conduit. • Remote wiring must not...minimum of 20 AWG, 600V, cable twisting 1.5 to the "POOL" or "SPA" mode and set the desired setpoint (eg. 102 °F for Spa). 3. REMOTE CONTROL WIRING
Important Installation Notes for Remote or ...
Operating Instructions - Page 46
...Circuit Board
"Water Sw Open" "Hi Limit 1 Fault" "Hi Limit 2 Fault" "Rollout Sw Open"
"Clock/Fireman Sw" "Vent/Field Sw #1"
Pressure switch.
Inspect internal Thermostat (Unitherm Governor) and bypass valve. Rollout Sensor - Press manual... (Replace valve.)
46 NO
YES
Push MODE switch to select "Pool" or "Spa"
Push Temp arrow to scroll to chart below . Heater Fired?
Check for instructions...
Warranty - Page 1
...the installation site. performance problems caused by a qualified licensed installer in accordance with a pool or spa by a properly licensed installer will not pay labor costs for the HEATER and component...Raypak will be between 7.4 and 7.8 and total alkalinity between the heater outlet and the pool/spa, or not maintaining a proper chemical balance (PH level must be warranted for the ...
Similar Questions
P-m266a-en-x Pool Heater Water Switch Open Error Message.
how do I adjust/replace or reset the water pressure switch on the pool heater. The manual included w...
how do I adjust/replace or reset the water pressure switch on the pool heater. The manual included w...
(Posted by pricerd 2 years ago)
Sns On Display.
When I turn on the unit it will display RV1 and the temp for a couple of seconds and then display SN...
When I turn on the unit it will display RV1 and the temp for a couple of seconds and then display SN...
(Posted by Weirdo23 9 years ago)
What Does Error Message Rollover Sw Open Mean
pool heater is one year old and this season when turning system on we get an error message that says...
pool heater is one year old and this season when turning system on we get an error message that says...
(Posted by mrndeutsch 9 years ago)
Time Clock/fireman Switch Circuit Is Open. What Does This Mean?
I had a replacement circuit board put in about 10 days ago and now the display shows the time clock/...
I had a replacement circuit board put in about 10 days ago and now the display shows the time clock/...
(Posted by Sam3506 10 years ago)