Home » Pfaff » Sewing Machines » Pfaff hobby serger

Pfaff hobby serger Support Question

Find answers below for this question about Pfaff hobby serger.
Need a Pfaff hobby serger manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by yowilson on November 1st, 2021

Pfaff Hobby Serger Ts381a Is Any Good?

Is pfaff hobby serger ts381a any good? Would I be better off getting a new? Please recommend me one. Learning to sew, but ready for a serger...I think.What should I look for in a serger?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on November 2nd, 2021 8:55 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,609,790

1,100
points

Are Pfaff Sergers any good?

User Friendly: The Pfaff Coverlock 3.0 serger is a dream to operate and easy to master. Detailed Instructions: This machine includes comprehensive threading instructions in the manual and on a step-by-step DVD. Quiet Operation: Solid engineering ensures quiet, nearly vibration-free operation, even at top speed.

New models below -lots of new features.

https://www.pfaff.com/en-us/machines

https://www.pfaff.com/en-US/Machines/Overlock

https://www.amazon.com/Pfaff-Serger-TS381A-Overedging-Machine/dp/B08FWLDHXQ

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Pfaff hobby serger Manual Pages

Owner's Manual - Page 3

.... PREPARATION FOR FORMING THREAD CHAIN 8 FORMING THREAD CHAIN 8 START TO SEW 9 SECURING TAIL CHAINS 9 • Check machine is threaded correctly before sewing. JOIN TWO PIECES OF FABRIC 12 CARING FOR YOUR MACHINE 12 CHANGING NEEDLE 12 PERFORMANCE CHECKLIST 12 - BLINDSTITCH 11 CONTACT YOUR PFAFF DEALER DECORATIVE FLATLOCK 12 WHERE YOU PURCHASED THIS PRODUCT. TURNING...

Owner's Manual - Page 4

... dials until threading is plugged into machine) Sewing speed selector Low (toward "I tCT) . 14 10 18 N \ 12 13 - 17 1. Front cover (#287569), covers mecha nism. Foot switch (#287597) runs machine. 2. Spool pin and cap holds top thread supply and prevents thread tangling. 4. Handwheel provides a means for your machine. -2- 16. Seam guide (#287624) helps keep...

Owner's Manual - Page 5

...in machine) #2020-014 3 x Demo thread spool (on machine)...x Needles (1 in light will go out. • Connect foot switch (3) to run machine and turn on light (under spool or spool stand. i • Unplug toot switch.... each x Thread cap (medium size) #287539 (on machine) 3 each x Thread cap (large size) #287537 CONNECTING AND RUNNING MACHINE V2 / • Connect AC adaptor (1) cord into ...

Owner's Manual - Page 6

... LOOPER UPPER LOOPER THREAD TOO THREAD TOO LOOSE LOOSE NEEDLE THREAD TOO LOOSE '3l377 CHARACTERISTIC • When seam is complete continue sewing, lightly pulling fabric toward ALTERNATIVE left rear corner of machine chaining ADJUSTMENT off and forming thread tail. • Cut thread tail between presser foot and fabric. Turn lower Turn upper...

Owner's Manual - Page 7

... size Parallel wound / Medium cap -- i JJi \ I\ • Remove old thread spools. • Place new thread spool. • Tie new and old threads. TYING ON THREADING • Clip thread in front of spool to spools. PREPARATION FOR THREADING • Your machine comes threaded. If you wish to change thread, an easy method for threading...

Owner's Manual - Page 10

... two discs. • Pull thread down through guide (0-3), then up and down through guide (C-i). 0 • Thread needle from front to back. • Draw thread to sew on your fabric.

Owner's Manual - Page 11

... clamp body Note: edge guide is complete continue sewing, forming thread tail for next sewing. -9---- Outside Corner - • Sew to approximately 11/64 inch (4.2mm). TURNING SQUARE CORNER • Select High or Low sewing speed. • Stan stitching. \ • Lightly guide fabric. • When seam is preset to limit stitch width to point A, one...

Owner's Manual - Page 12

... end of area to be restitched, overlap stitching 1 inch (25mm). • Remove fabric and sew tail chain. • Puil fabric to left in straight tine. • Stitch and hold fabric in fabric. IH (I nside Corner - down on lever) • Pivot ...

Owner's Manual - Page 13

... right side and press. -11 • Pull fabric open and press stitching flat. LkI • Place fabric under presser foot and align seam guide. • Sew one or more lines of decorative flatlock stitches. • Turn fabric to wrong side. • Fold hem back as shown. 4.2mm - 0 LI • Place folded...

Owner's Manual - Page 14

... not connected. • Insert needle correctly or replace with power source. (page 3) When stitches skip. • Add one drop of sewing machine oil to guide the fabric. • Tighten screw firmly. • Thread machine correctly. (page 6,7 & 8) • Replace needle. (page 12) • Adjust tension. (page 4) • Thread correctly. (page 6,7 & 8) • Insert needle correctly...