GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by crick1960 on April 10th, 2021
Disconnecting Smoke Detector
Have The GE ATP1000 and have a GE ESL429/449 detectors. Have one bad. How can I disconncet that one detector on the panal. Thank you
Current Answers
Answer #1: Posted by Troubleshooter101 on April 13th, 2021 1:13 PM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,060
Member since:
September 30th, 2015 Points: 2,927,060
Please check this link below:-
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
...Installation
The ATP1000 lets you control all programming and operation of the system. The door can also be activated anytime. The touchpad includes ...touchpad. • Table 2 describes the maximum wire lengths allowed between the touchpad and the panel.
A built-in an environmentally controlled area (32°F to 120°F/0°C to indicate the current status of compatible security...
Installation Instructions - Page 2
... at the top of the mounting plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5.
For wall mounting, place the mounting plate on the touchpad and swing the touchpad bottom toward the mounting plate. Figure 2. ing plate to the Mounting Plate
Align the tabs...
Installation Instructions - Page 3
... the display shows SECURITY. 5. Press A or B until the display shows ACCESSORY MODULES, then press ƒ. When using the ATP1000 as a permanent part of the touchpad.
7. ATP1000 Touchpad/Display Installation Instructions
3 Programming Connecting the Touchpad for system programming to the Programming Touchpad Header on the panel. Verify that don't include an alphanumeric touchpad as...
Installation Instructions - Page 4
... shows SYSTEM MENU, then TIME AND DATE (Concord panels with software versions 1.0-1.6:
1. Press B twice and the display shows TOUCHPAD BRIGHTNESS 2 (default setting). 4. ting and brightness level. 6. The display shows DA nnn.
2. Reconnect the AC and backup battery power. Press ƒ. Exit program mode and disconnect the programming cable from panel memory. Note Contact...
Installation Instructions - Page 5
...touchpad unit number (see procedure on this time, the touchpad is plugged in Concord RF systems. 5. Note At this page). (Concord panels with software versions 1.01.6 only.)
Changing the Touchpad Unit Number (Concord...) at touchpad and panel terminals.
2. However, if the new touchpad unit number has never been
ATP1000 Touchpad/Display Installation Instructions
5 Touchpad display shows...
Installation Instructions - Page 6
...;8hhqh UrpuvphyÃT
6
ATP1000 Touchpad/Display Installation Instructions The display shows SCANNING BUS DEVICES...panel may cause harmful interference to radio communications. Compatibility Concord, Concord Express, Concord Ultra Power Requirements 12 VDC nominal (See Table ...installation requirements for help.
)
©2003 GE Interlogix. This equipment generates, uses, and can...
Similar Questions
Program Time And Date On Touchpad
(Posted by Samtalmer 12 years ago)
Sensor Beeping
There is a fire sensor beeping and I cannot dissable it. Is there a silence button?
There is a fire sensor beeping and I cannot dissable it. Is there a silence button?
(Posted by bagelmom3 12 years ago)
How Do We Disarm Our System And When Do We Type In Security Code?
(Posted by carolyn2707 13 years ago)
How Do I Disconnect The Detector
the green flash light is flashing every a few seconds, and beep every a few minutes, the alarm has b...
the green flash light is flashing every a few seconds, and beep every a few minutes, the alarm has b...
(Posted by Haitongz 13 years ago)
How Do I Disconnect The Detector
It's a five year old unit that is indicating it's expired. How do I disconnect it and connect a new ...
It's a five year old unit that is indicating it's expired. How do I disconnect it and connect a new ...
(Posted by bill61236 14 years ago)