Dell PS6000 Support Question
Find answers below for this question about Dell PS6000.Need a Dell PS6000 manual? We have 1 online manual for this item!
Question posted by joykayonkr on April 26th, 2014
How To Connect One Hba To Equallogic Arrays In Different Groups
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Dell PS6000 Manual Pages
Configuration Guide - Page 6
... This document should not be used to connect hosts to the EqualLogic-based virtual storage volumes, some assumptions made ...HBAs), and iSCSI initiators can be created. This document focuses on page 61
Dell EqualLogic Configuration Guide v11.3
1 The Dell EqualLogic Configuration Guide is considering purchasing or has purchased an EqualLogic PS Series Array(s) for use within an EqualLogic...
Configuration Guide - Page 8
... 128 per pool
16 32
7
1 In a mixed group of PS6000, PS6500 and PS4000 the higher limits normally prevail 2 In a mixed group of PS6000, PS6500 and PS4000 arrays the maximum number of PS4000 arrays in a group (snapshot and replication) Volume connections per pool and per group (each Table 1: Array Models
2.2 Feature Comparison
The Dell EqualLogic PS6000 Series provides the full range of features...
Configuration Guide - Page 14
...parity block. Arrays (or group members) within a chassis
Table 5: RAID 5 Drive Layouts
For EqualLogic arrays using the Command Line Interface.
2.4 RAID Policies
Each array in an EqualLogic array group is not
supported
(a) 48 drive arrays implement multiple ... RAID 5 implementations can be placed on a different disk ensuring that are not located on a single disk in Table 5 above.
Configuration Guide - Page 15
... same time without data loss. For EqualLogic arrays using the hot spare drive layouts specified in each array and the hot spare configuration. Table 7: RAID 6 Drive Layouts
Table 8 shows the amount of the data blocks depending on the number of random writes. Each parity block generates parity using a different ―view‖ of raw...
Configuration Guide - Page 16
...by first building a series of raw storage available can tolerate one drive failure per mirror pair. For EqualLogic arrays using the hot spare drive layouts specified in Table 9 above.
Disk Drives
Hot Spare
No Hot ... performance RAID types: RAID 0 and RAID 1. Table 9: RAID 10 Drive Layouts
For EqualLogic arrays using a RAID 10 policy, the total quantity of two disk RAID 1 mirrored sets,...
Configuration Guide - Page 17
...would result in Table 11 above.
Table 11: RAID 50 Drive Layouts
For EqualLogic arrays using a RAID 50 policy, the total quantity of raw storage available can tolerate...of disk drives.
(b) 48 drive arrays implement stripes across multiple RAID 5 sets within a single chassis. (c) 48 drive arrays cannot implement a no hot-spare policy. For EqualLogic arrays using the hot spare drive layouts ...
Configuration Guide - Page 19
...different RAID policy if it is called a group member.
Dell EqualLogic Configuration Guide v11.3
14 Each array in the group for maximum storage utilization, a tiered storage system allows for the administrator to optimize different arrays for use within the group... process. (See Section 2.3.4 on page 7 for more PS Series arrays connected to an IP network. There is always at least 1 pool -...
Configuration Guide - Page 22
... provisioned volumes:
Use Pool Free Space, not Group Free Space when making all determinations of thin provisioned volume ...EqualLogic Configuration Guide v11.3
17
The following :
Ability to define a volume as a thin provisioned volume at any given time. Thin provisioning allows volumes to present a logical capacity to the host(s) connecting to the volume that is different...
Configuration Guide - Page 29
... If you can result in data loss. The EqualLogic array will not manage concurrent access to any volume.
Replication Space
Local Reserve (Primary Group)
Recommended Value
No Failback Snapshot:
100%
Keep Failback Snapshot:
200%
Space Efficient Value
5% + CR(a)
10% + CR(a)
Replica Reserve (Primary Group)
200%
105%(b) + CR x (# of Replicas - 1)
Delegated Space (Secondary, for...
Configuration Guide - Page 30
...arrays and the group's well known IP address.
Rapid Spanning Tree Protocol must be connected to support all ports should be in a different subnet as long as those hosts have layer 3 routing available to support the use of an EqualLogic... server can be configured to register with Firmware V4.1.4, volume and snapshot identifiers are required to the same subnet.
The arrays ...
Configuration Guide - Page 31
... group that do not carry iSCSI traffic, or on WANs, where bandwidth is not currently supported for fully redundant SAN connectivity.
Dell recommends against using QoS with EqualLogic SANs. If you use it for certain types of your switch's VLAN capabilities. If necessary, create a second VLAN for other applications and the PS Series array...
Configuration Guide - Page 32
... more hosts connected to one or more buffer space per port that a switch can send packets in an EqualLogic SAN must meet the following general requirements:
Low latency Switches with other (non-iSCSI SAN) network traffic. Most iSCSI SAN implementations should be able to passively respond to support inter-array communication and...
Configuration Guide - Page 33
...ports or at least 40Gb/s in such a way that each switch connected to the array group members will provide a set of 1Gb and 10Gb arrays. The switch should be at least two 10Gbps ports.
Figure 9..., low-latency interconnect that allows two or more EqualLogic arrays into a single group may be required. The switch should be interconnected to provide a single switched Ethernet fabric.
Configuration Guide - Page 37
... the LOM controller available for other connections. Figure 11 Redundant NIC Connections from Server to the server LAN. Dell EqualLogic Configuration Guide v11.3
32 4.4 Host Configuration Guidelines
4.4.1 Recommendations for Host Connectivity in Figure 11 below. NIC Connections
to achieve redundant server NIC connection configurations for connecting to SAN using one additional dualport...
Configuration Guide - Page 40
... environment, this SAN design, each component of the SAN infrastructure has a redundant connection or path. Actual implementations will vary depending on customer's actual network infrastructure. ... 13 Redundant SAN
Dell EqualLogic Configuration Guide v11.3
35
The information provided here will not be illustrated that utilizes an EqualLogic array is illustrated in Figure ...
Configuration Guide - Page 41
... provide end-to data stored in this section will allow host connectivity to -end redundant connection paths. Single Controller Single Switch Single NIC
Single Controller Single Switch Dual NIC
Single Controller Dual Switch Dual NIC
Table 19 Single Controller Array Configurations
Dell EqualLogic Configuration Guide v11.3
36 4.5.2 Partially Redundant SAN Configurations Each of the...
Configuration Guide - Page 42
Dual Array Controller Configurations You can configure a Dell EqualLogic array to run using a single array controller. Table 20 below shows configurations using dual controllers. Dual Controller Single Switch Single NIC
Dual Controller Dual Switch Single NIC
Dual Controller Single Switch Dual NIC
Table 20 Dual Controller Array Configurations
Dell EqualLogic Configuration Guide v11.3
37
Configuration Guide - Page 45
...I/O modules and external switches are from different vendors Using 10GbE port options...following guidelines for blade server integration with the Dell EqualLogic PS Series, available ... Chassis
Use the following Dell EqualLogic whitepaper for SAN infrastructure connectivity
Blade I /O...an external set of a SAN if arrays are directly connected them. Stack blade I/O modules...
Configuration Guide - Page 48
...arrays being deployed as well as the type of uplink technology being used to connect the M1000e I/O stacks to the external tier stack.
5.6 Stack to Stack Interconnect
Connecting... server's optional Ethernet mezzanine card to use for use with EqualLogic SAN...same vendor)
Dell EqualLogic Configuration Guide v11.3
43
If possible, any Link Aggregation Group used for connecting the I/O modules ...
Configuration Guide - Page 71
... PS Series SAN with Existing SANs
Understanding Data Replication Between Dell EqualLogic PS Series Groups
Published in an OLTP Environment Using Dell EqualLogic PS Series (EqualLogic support site - registration required) Integrating EqualLogic PS6x10 Arrays with SAN Headquarters
PS Series Groups: Backup and Recovery Overview
Dell EqualLogic Configuration Guide v11.3
66 In future versions of...
Similar Questions
Can We Connect Sas & Sata Hdd On T610 Server Backplane
(Posted by Ahgen50 9 years ago)
Dell R710 How Many Different Raid Arrays Are Supported
(Posted by browlm 10 years ago)
What Is Qle4060c Configuration Setting Connected To Dell Equallogic Ps6000 Array
(Posted by techit 11 years ago)
Raid 5 Hard Drive Can We Connect In Dell Poweredge Iii 2950 Server
DEAR SIR THIS IS MOHAMMED AZAM I WANTS CONNECT RAID 5 HARD DRIVE OF 1 TB CAN I CONNECT THIS DRIVE W...
DEAR SIR THIS IS MOHAMMED AZAM I WANTS CONNECT RAID 5 HARD DRIVE OF 1 TB CAN I CONNECT THIS DRIVE W...
(Posted by azammohammed2006 11 years ago)