Craftsman 25980 Support Question
Craftsman 25980 Support Question
Find answers below for this question about Craftsman 25980 - Accu-Rip Saw Guide.Need a Craftsman 25980 manual? We have 1 online manual for this item!
Question posted by wasaprof on September 29th, 2012
Replacement Cut Guide And Handle For Craftsman Accu-rip Saw Guide
Figure 1 of owner manual shows cut-guide handle (D) and cut guide (E). I have lost mine and would like to order a replacement. Sears' site shows that the entire device is no longer available. where can I obtain these parts, so I can use my accu-rip?
Current Answers
Related Craftsman 25980 Manual Pages
User Instructions - Page 1
...User instructions when adjusting, attaching, or using a circular saw to make your saw .
1 Model No. 25980
ACCU-RIP SAW GUIDE USER INSTRUCTIONS
About the Accu-Rip Saw Guide
The Accu-Rip is designed to fit RightHand Blade circular saws only. The Operator Tips section gives useful information on the material.
§ Allows you would normally cut with the current major brands of this User...
User Instructions - Page 2
... only loosen and retighten these parts as a worktable, so that there is unplugged from the power source!
(D) Cut-Guide Handle
(E) Cut-Guide
Fig. 1
71 Loosen the Cut-Guide handle (D), and slide the Cut Guide (E) to fit most circular saws with that prevent the use of the T- HOW TO SET UP AND ATTACH THE ACCU-RIP TO YOUR SAW
Make sure your saw blade guard. Do not...
User Instructions - Page 3
Fig. 5a Push the Accu-Rip towards the saw until the AccuRip is largely determined by the location of available space for tightening and loosening these onto the base plate. Depending on your saw's design, at this point you... of the L-Brackets and T-Bolts will vary on the Accu-Rip Saw Guide, insuring correct cutting widths. This will need to loosen the T-Bolts slightly more to allow you may ...
User Instructions - Page 4
... and easier. This is Aligned with different saw . The Accu-Rip Saw Guide will make a slight indention in an Open area for your saw designs. Should it be UP! Blade Guard must be necessary to reset the Accu-Rip for you may vary with Edge
(B) Retainer Screw
Fig. 6a
Fig. 6a Shows the L-Brackets positioned properly.
The sharp points...
User Instructions - Page 5
... of the material can cause the saw . Use the "push-plate" on the top of the material during use . This is pushed firmly against the edge of the Cut-Guide (E) to the desired dimension, and tighten the Cut-Guide handle using the Accu-Rip, you find that the vertical section of The Accu-Rip is especially important when making wider...
User Instructions - Page 6
... sometimes shown on the Accu-Rip and tighten the Cut-Guide Handle, to prevent interference while making bevel cuts. You should re-position the AccuRip Saw Guide before making your crosscut.
2) With the Cut-Guide held in place at Desired Width
Fig. 10
MAKING CROSS-CUTS WITH THE ACCU-RIP ATTACHED
To make bevel or angle cuts. Fig. 10 shows a bevel cut being made with the...
User Instructions - Page 7
..., or other debris from the moving parts, and from the saw for the material that the Accu-Rip be stored in a straight line through the last portion of material you should push your saw during the cut . The type of your cut . CARE AND STORAGE OF YOUR ACCU-RIP
§ It is a precision tool, and should be hung in good...
User Instructions - Page 8
...Improper saw .
2. Sharpen or replace blade.
3. Re-align and re-tighten T-bolts and Cut-Guide Handle.
6. Accu-Rip Zero mark is not flush with sawdust or debris.
1. Cut-Guide Handle has loosened on your cut too quickly.
5. Cut-Guide Handle is not straight
Cut-Guide does not slide smoothly
1. Loosen Cut-Guide Handle to desired cutting width and tighten Cut-Guide Handle. Making a cut...
Similar Questions
Motor Carbon Brushes
Hello....I'm looking for substitute parts, the original are not longer available.It's for a Craftsma...
Hello....I'm looking for substitute parts, the original are not longer available.It's for a Craftsma...
(Posted by jriofrio 11 months ago)
The Edger Guide Is Loose .how To Fix It
How To Fix Edger Guide Close To Blade
How To Fix Edger Guide Close To Blade
(Posted by salam403 7 years ago)
How To Replace A Broken Spring Of 71/4' Craftsman Slide Compound Miter Saw. Mode
I've a spring broken of 71/4" craftsman slide compound miter saw. Model 137.211940. Please tell me h...
I've a spring broken of 71/4" craftsman slide compound miter saw. Model 137.211940. Please tell me h...
(Posted by ccc692 8 years ago)
Or91721 Replacement Belt
What is a replacement belt that can purchased with out a month relay from order from Sears Parts?
What is a replacement belt that can purchased with out a month relay from order from Sears Parts?
(Posted by Spauldid51 11 years ago)
Maximum Cut Depth For 21609 Scroll Saw
I can't find the maximum depth of cut that you can make with the 21609 scroll saw - can you please t...
I can't find the maximum depth of cut that you can make with the 21609 scroll saw - can you please t...
(Posted by brian78088 12 years ago)