Craftsman 79653 Support Question
Craftsman 79653 Support Question
Find answers below for this question about Craftsman 79653 - 12 Amp Edger.Need a Craftsman 79653 manual? We have 1 online manual for this item!
Question posted by salam403 on September 9th, 2016
The Edger Guide Is Loose .how To Fix It
How To Fix Edger Guide Close To Blade
Current Answers
Related Craftsman 79653 Manual Pages
Instruction Manual - Page 1
..., read this manual and follow all its Safety Rules and Operating Instructions.
www.sears.com/craftsman It is a powerful cutting tool. Instruction Manual for Electric Edger
EZ.Edge.n.Store
Model No. 71.79653
BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE FIRST CALL (800) 539-6455
IN MOST CASES A CRAFTSMAN REPRESENATIVE WILL BE...
Instruction Manual - Page 2
WARNING: Some dust created by using power tools contains chemicals known to the state of California to cause cancer and birth defects or other
reproductive harm.
Instruction Manual - Page 3
..., birth defects, or other reproductive harm. WARNING: Certain dusts created
when using the edger, always wear safety glasses and gloves and dust masks that are designed to state.
..., Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
READ ALL INSTRUCTIONS BEFORE OPERATING TOOL
A
"
•
WARNING TO CALIFORNIA
RESIDENTS: Handling the cord on working with accessories
sold for...
Instruction Manual - Page 4
...a safe distance from this tool is 14 AWG for 25 feet, 12 AWG for 50 feet, and NOT RECOMMENDED for the edger. Use receptacles with a polarized plug only one blade is recommended. This unit ...not in a dry location - Use only
*The wire size (AWG) for 120-Volt appliances using 12-16 amps is double-insulated, a two wire extension cord (an extension cord without a ground) may be kept...
Instruction Manual - Page 5
...replace cords if any other
persons and pets when using the edger. * STAY CLEAR OF BLADE: Always stand to the left of the unit when
using edger. = DON'T OVERREACH - Unplug unit and wait for ... the unit operates properly. Also inspect the connections to contain long hair. Do not wear
loose clothing or jewelry. Keep the cord away from the receptacle. The smaller the gauge number,...
Instruction Manual - Page 6
...BLADE when picking up into the shaft and wilt allow the shaft to use this tool...
SAVE THESE INSTRUCTIONS
A
t,
Remove the Edger and all its parts from blade area. " STOP THE MOTOR WHEN THE...BLADES SHARP.
* KEEP HANDS AND FEET away from cuttinga_a.
6
Fij.ig.rue -2
Shaft-to full-length. onotoperattehetoolwhen 1. Inspect for damage. NOTE: The shaft of THREE
height settings with loose...
Instruction Manual - Page 7
...edger blade wilt only contact dirt before turning on the top of the cut, move the front adjustment lever up or down until the button locks in place.
Cutting depths are firmly seated into shaft housing without fully extending and securing shaft as shown in Figure 4. Secure the shaft with a fixed edge guide... that it easy to remove the blade cover. ATTACHING...
Instruction Manual - Page 8
... with wet growth or in the rain.
The Edge-n-Store Edger shaft can be
8 To turn ON.
* Do not use the edger with both hands and turn off the unit, release the trigger... and the safety switch wilt snap out to prevent the trigger switch from blades. STORAGE POSITION
CAUTION: If the edger becomes jammed or stalled on the trigger (under the handle) with your thumb while...
Instruction Manual - Page 9
...smaller wrench (included) by
•=A
PREVENTING CORROSION Fertilizers and other edger parts.
BLADE CHANGE/TURN = The EZ- Do not store the unit on ...unit is too difficult to hold the blade retainer while loosing the lock nut with warm water and...in water. Never spray-wash tool or immerse in a clockwise direction. To change or flip the blade, put the blade retainer in . If issues ...
Instruction Manual - Page 10
... to be running slow
Solution: You may need to the information on managemyhomeocom
:: • Find this manual concerning proper extension cord wire size. Insure the blade guard is in place. Solution: Make sure that it is working properly and is firmly seated in the "on" position. for free!
10
Instruction Manual - Page 31
NEEMDORP.E_
i
° Findthisand aU yourotherproductmanuatsonline.
• Geat nswefrosmourteamofhomee×perts. • Geat personatimzeadintenapntcae_foryouhr ome.
• Find information and tools to help with home projects.
Similar Questions
I Cannot Find The Blade Part For 79653 12 Amp Edger
(Posted by Frnkfmn 9 years ago)
.how To Use The Edger???
I lost my manual and I need to have simple instructions on how to safely operate the edger.
I lost my manual and I need to have simple instructions on how to safely operate the edger.
(Posted by elainelmasse 9 years ago)
Replacement Blade For The Ez-edge-n-store Edger Modle#79653?
Where can I purchase a replace blade for this edger?
Where can I purchase a replace blade for this edger?
(Posted by Lgagliano 11 years ago)
Cord Will Not Retract On Craftsman Incredi-pull Gas Powered Trimmer/edger 32cc
how do you remove the top to get rope "spool"?
how do you remove the top to get rope "spool"?
(Posted by dglynch 12 years ago)
Edger Quiting
my craftman model 79653 keeps dying while in use. if i let it rest several minutes it will start ag...
my craftman model 79653 keeps dying while in use. if i let it rest several minutes it will start ag...
(Posted by marielani 13 years ago)