BenQ PB8260 Support Question
BenQ PB8260 Support Question
Find answers below for this question about BenQ PB8260 - XGA DLP Projector.Need a BenQ PB8260 manual? We have 1 online manual for this item!
Question posted by srussell14245 on January 11th, 2014
Troubleshoot Benq Pb8260
on power up power green comes on fan starts, then temp led flashes once, fan stops but green power light stays on
Current Answers
Related BenQ PB8260 Manual Pages
User Manual - Page 1
PB8260 Digital Projector Installation Series User's Manual
Welcome
User Manual - Page 2
...specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication may be reproduced, transmitted, ... changes.
*DLP, Digital Micromirror Device and DMD are copyrights of Texas Instruments. Others are trademarks of their respective companies or organizations. Disclaimer
BenQ Corporation makes...
User Manual - Page 3
Table of contents
Important safety instructions 1
Introduction 5
Projector features 5 Shipping contents 6 Projector exterior view 7 Controls and functions 9
Positioning your projector 13
Choosing a location 13 Obtaining a preferred projected image size 14
Connection 16
Wireless connection 16 Cable connections 16
Operation 19
Start up 19 Preparing for a wireless presentation 20 ...
User Manual - Page 4
Troubleshooting 44
Common problems & solutions 44
Specifications 45
Projector specifications 45 Dimensions 46 Timing chart 46
Warranty 48
Limited warranty 48
Regulatory statements 49
FCC statement 49 EEC statement 49 MIC statement 49
iv Table of contents
User Manual - Page 5
.... Important safety instructions
Your BenQ projector is designed and tested to meet the latest standards for future reference.
• In some countries, the line voltage is
• Do not look straight at the projector
NOT stable. Save this user's manual before you connect your
projector through a power stabilizer,
surge protector or uninterruptible
power supply (UPS). Refer...
User Manual - Page 6
... securely installed.
2 Important safety instructions Please use BenQ's Ceiling Mounting Kit for replacement.
4.
This product is capable of the projector or electric shock when the appliance
is unplugged.
... serious damage.
5. Never replace the lamp assembly or any electronic components unless the projector is subsequently used.
3. To reduce the risk of lamps beyond the rated lamp...
User Manual - Page 7
..., overheating inside of 8. Important safety instructions 3
Do not place this projector in a fire.
9. If the ventilation holes are higher than 10 degrees left to the unit.... Locations near the
- Safety Instructions (Continued)
7. projector.
- Locations with an ambient temperature above 40°C / 104°F
-
Do ...
User Manual - Page 8
... as this could cause the objects become wet, disconnect it from the power supply's wall socket and call BenQ to have the projector serviced. Besides probable physical damage to fail. Do not block the projection lens with any objects upon it to the projector, doing so may cause it .
13. Liquids spilled into the...
User Manual - Page 17
... rear projection screen is the most common way to position the projector for this setting with the projector placed near the floor behind the screen.
III.
Floor in front of screen;
Positioning your projector 13 Note that a special rear projection screen and the BenQ Projector Ceiling Mounting Kit are required for quick setup and portability...
User Manual - Page 18
... the screen, you have to tilt it down or up to center the image on the screen after turning the projector on the screen, in these situations image distortion will occur. BenQ has provided separate tables of dimensions for both 16:9 and 4:3 screen ratios to assist you have. Obtaining a preferred projected image...
User Manual - Page 20
... User's Manual for each source. 3. Insert the wireless card to your laptop to enable you to your projector and install the necessary software onto your projector. We do not guarantee it works correctly with BenQ PB8260 projector. Ensure the cables are firmly inserted.
16 Connection The eject button pops out once the card is an...
User Manual - Page 23
... cap. Press and hold (for 2 seconds) the Power button on the power point (if switched).
3. Switch all of start up your computer
Projector boot screen
Operation 19 Turn the main power switch on . 2. The Power indicator light flashes green when the unit is installed in the projector and its indicator lights green, set up , a default BenQ logo is left on, it is projected...
User Manual - Page 31
... is complete or
during the cooling process.
3. Press Power and a confirmation prompt message displays. Operation 27
start the projector after the fans stop. Press Power again to start the projector within minutes, the fans will not respond to re- To turn the projector off . Note: • Do not unplug the power cord before the projector shutdown sequence is not properly shut down...
User Manual - Page 37
...Determines the length of time before the projector will appear during projector start-up. Three modes are provided so you can optimize your projector image setup to suit your last ...are available: Default (BenQ logo), black screen or blue screen.
The range is restarted. Keystone Hold
When selected, preserves the last keystone correction value even when the projector is from among ...
User Manual - Page 38
... , it may cause a higher decibel operating noise level because of increased fan speed necessary to state that this projector under "High Altitude Mode" may display auto shut-down symptoms, which is...If you use this projector can operate under any and all harsh or extreme environments.
34 Operation We recommend you use the High Altitude mode when your BenQ projector from over-heating. In...
User Manual - Page 40
.... Contact your dealer if other chemical detergents. Use a canister of the projector. Never use lens-cleaning paper or moisten a soft cloth with a soft, dry, lint-free...turn the projector off and wait until the fans stop running.
2.
Turn the project off and unplug the power cord.
Open one dust filter cover from any parts of the
projector.
Cleaning the projector case
...
User Manual - Page 41
... a message displayed on the power again. Transporting the projector
It is difficult to the Spec.
Storing the projector
If you ship the projector with its original packing or equivalent. If the covers are not correctly seated in the manual or consult your dealer or visit BenQ website at www.BenQ.com for the projector. Please refer to...
User Manual - Page 48
... to the input source device. Stand within 6 meters (19.5 feet) of the projector.
44 Troubleshooting Cause
Remedy
There is switched on again during the cooling process.
Turn the video source on and check that it is no power from the projector. BLURRED IMAGE
Cause
The projection lens is not correctly connected to the lens...
User Manual - Page 49
... system Lens F/Number Lamp
Electrical
Power supply Power consumption
Mechanical
Dimensions Weight
Input terminal
Computer input RGB input DVI-I input
Video signal input S-VIDEO VIDEO
HDTV signal input Audio signal input
Audio 1
Output
USB mouse connector Speaker RGB Audio L/R
Control
RS-232C
Digital Projector PB8260 1024 x 768 XGA
1-CHIP DMD F/2.4 PB8260
300W lamp
AC100 ~ 240V, 4.5A...
User Manual - Page 52
... other rights which you may have other information, please refer to BenQ Warranty Information Book.
48 Warranty Proof of purchase date will be replacement of any defective ...BenQ's written instructions, especially the ambient humidity must be in-between 10% and 90%, temperature in-between 0°C and 40°C, altitude lower than 10000 feet, and avoiding to operate the projector...
Similar Questions
Color Of Projector Green
what causes a BenQ sp870 projector to project black and green image??
what causes a BenQ sp870 projector to project black and green image??
(Posted by ilarin 9 years ago)
Replacing The Lamp In My Benq Mp 610 Dlp Projector
how can i replace the lamp inmy projector
how can i replace the lamp inmy projector
(Posted by martyahill 11 years ago)
Benq Ms612st Dlp Projector No Signal
Connecting with VGA cable but "No Signal" is displayed then "Source Detect" on Computer 1 then back ...
Connecting with VGA cable but "No Signal" is displayed then "Source Detect" on Computer 1 then back ...
(Posted by pjay02111960 11 years ago)
Please Help Me!!! Reset The Lamp Of The Benq 8260 Projector
Hi I change the new lamp. and the led of the lamp continus flashing again. How can i reset the proje...
Hi I change the new lamp. and the led of the lamp continus flashing again. How can i reset the proje...
(Posted by milicupa 12 years ago)
Benq 820 Dlp Projector
In the past 24 month I have purchased 8 Benq 820 projectors. They work fine for about 6 months and w...
In the past 24 month I have purchased 8 Benq 820 projectors. They work fine for about 6 months and w...
(Posted by chijoh 13 years ago)