Owner's Manual
Page 3
...FCC Regulations, Part 15 for Class "B" digital devices. In the case of product. The above statements apply ONLY to eliminate the problem by using one of the NEC that provides guidelines for service. 20 Replacement Parts - Note to CATV system installer: This reminder ... not guarantee that are required, be connected to the grounding system of interference, which can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. IMPORTANT SAFETY INSTRUCTIONS 24 Outdoor Antenna Grounding - When replacement parts are...
...FCC Regulations, Part 15 for Class "B" digital devices. In the case of product. The above statements apply ONLY to eliminate the problem by using one of the NEC that provides guidelines for service. 20 Replacement Parts - Note to CATV system installer: This reminder ... not guarantee that are required, be connected to the grounding system of interference, which can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. IMPORTANT SAFETY INSTRUCTIONS 24 Outdoor Antenna Grounding - When replacement parts are...
Owner's Manual
Page 34
...correct because the volume was changed during the auto setup procedure. • If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again. • If warning W-1, W-4 or W-5 appears, corrections are made, but they may appear ... The difference of volume level among speakers is excessive. (No level correction is made . • If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center. 30 AUTO SETUP After auto setup Press l / h to the listening position. This message may not be optimal. • If warning W-2...
...correct because the volume was changed during the auto setup procedure. • If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again. • If warning W-1, W-4 or W-5 appears, corrections are made, but they may appear ... The difference of volume level among speakers is excessive. (No level correction is made . • If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center. 30 AUTO SETUP After auto setup Press l / h to the listening position. This message may not be optimal. • If warning W-2...
Owner's Manual
Page 90
..."OFF", and no video signal is set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem This unit fails to the chart below does not help, set to Set GRAY BACK to "AUTO" to "AUTO". 40 "ANALOG... function. 63 connected to "AUTO" or "DTS". 40 while playing a source encoded with a DTS signal. On-screen display does not appear. If the problem persists, the cables may be used have not Select the front speakers with INPUT, 33 selected. The input mode is set to "ANALOG" Set the...
..."OFF", and no video signal is set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem This unit fails to the chart below does not help, set to Set GRAY BACK to "AUTO" to "AUTO". 40 "ANALOG... function. 63 connected to "AUTO" or "DTS". 40 while playing a source encoded with a DTS signal. On-screen display does not appear. If the problem persists, the cables may be used have not Select the front speakers with INPUT, 33 selected. The input mode is set to "ANALOG" Set the...
Owner's Manual
Page 91
... the surround left and right speakers. No sound from all channels. The sleep timer has turned the unit off . Only the speaker on . If the problem persists, 13 the cables may be heard. Press STRAIGHT/EFFECT to "NONE". LFE/BASS OUT in the SET MENU is set Select "SWFR" or "BOTH... OUT in the SET Adjust the SPEAKER LEVEL settings. 57 MENU. Turn on . 39 You are set to cancel a mute. 35 Incorrect cable connections. TROUBLESHOOTING Problem The sound suddenly goes off. ADDITIONAL INFORMATION 87
... the surround left and right speakers. No sound from all channels. The sleep timer has turned the unit off . Only the speaker on . If the problem persists, 13 the cables may be heard. Press STRAIGHT/EFFECT to "NONE". LFE/BASS OUT in the SET MENU is set Select "SWFR" or "BOTH... OUT in the SET Adjust the SPEAKER LEVEL settings. 57 MENU. Turn on . 39 You are set to cancel a mute. 35 Incorrect cable connections. TROUBLESHOOTING Problem The sound suddenly goes off. ADDITIONAL INFORMATION 87
Owner's Manual
Page 92
... cables are connected correctly. 13 88 No connection from the outlet and - other settings on a turntable The turntable should be changed. TROUBLESHOOTING Problem Cause Remedy Refer to page Dolby Digital or DTS The connected component is not connected to Connect the source component to the analog AUDIO this... Digital or DTS digital instructions for your turnable to this unit through 21 low while playing a with low voltage. If the problem - cannot be heard. can be increased, (REC) jacks of this unit cannot be connected to the 21 GND terminal.
... cables are connected correctly. 13 88 No connection from the outlet and - other settings on a turntable The turntable should be changed. TROUBLESHOOTING Problem Cause Remedy Refer to page Dolby Digital or DTS The connected component is not connected to Connect the source component to the analog AUDIO this... Digital or DTS digital instructions for your turnable to this unit through 21 low while playing a with low voltage. If the problem - cannot be heard. can be increased, (REC) jacks of this unit cannot be connected to the 21 GND terminal.
Owner's Manual
Page 93
... multipath interference. The OSD may cause this unit cools down and then turn it is difficult to page - 63 - ■ Tuner Problem FM stereo reception is poor. There is disturbed. The signal is displayed. Remedy Check the antenna connections. Use a high-quality directional FM...when displaying OSD through component video connections. ADDITIONAL INFORMATION 89 Use the manual tuning method. Wait for about 1 hour until this problem when the transmitter is too far away or the antenna input is noisy. The signal is being used nearby. Cause The ...
... multipath interference. The OSD may cause this unit cools down and then turn it is difficult to page - 63 - ■ Tuner Problem FM stereo reception is poor. There is disturbed. The signal is displayed. Remedy Check the antenna connections. Use a high-quality directional FM...when displaying OSD through component video connections. ADDITIONAL INFORMATION 89 Use the manual tuning method. Wait for about 1 hour until this problem when the transmitter is too far away or the antenna input is noisy. The signal is being used nearby. Cause The ...
Owner's Manual
Page 94
... set incorrectly Set AMP/SOURCE/TV correctly. - Try setting another code of 6 m (20 ft) and no more than 30 degrees off- TROUBLESHOOTING ■ Remote control Problem The remote control does not work nor function properly. other remote control are weak. When operating the component selected by the input selector button, set .
... set incorrectly Set AMP/SOURCE/TV correctly. - Try setting another code of 6 m (20 ft) and no more than 30 degrees off- TROUBLESHOOTING ■ Remote control Problem The remote control does not work nor function properly. other remote control are weak. When operating the component selected by the input selector button, set .