Owner's Manual
Page 5
... Yamaha EMX512SC, EMX312SC, or EMX212S power mixer. Contents ■ Basic Quick Guide 6 Before Turning On the Mixer 6 Getting Sound to the Speakers 7 Adding Some Reverb 11 Using the Compressors to Enhance Vocals 12 Making the Most of Your Mixer 13 A Place for Everything and Everything in a wide variety of main and monitor output. Phantom Power...
... Yamaha EMX512SC, EMX312SC, or EMX212S power mixer. Contents ■ Basic Quick Guide 6 Before Turning On the Mixer 6 Getting Sound to the Speakers 7 Adding Some Reverb 11 Using the Compressors to Enhance Vocals 12 Making the Most of Your Mixer 13 A Place for Everything and Everything in a wide variety of main and monitor output. Phantom Power...
Owner's Manual
Page 9
... to 4, set both MASTER knobs to the XLR input jacks. If using phantom power, do not connect any devices other than powered speakers and amp, and then turn on the power to your inputs, set the PHANTOM switch to the LINE position ( ). EMX512SC/EMX312SC/EMX212S 9 4 If you have connected input devices to channels 1 to all connected...
... to 4, set both MASTER knobs to the XLR input jacks. If using phantom power, do not connect any devices other than powered speakers and amp, and then turn on the power to your inputs, set the PHANTOM switch to the LINE position ( ). EMX512SC/EMX312SC/EMX212S 9 4 If you have connected input devices to channels 1 to all connected...
Owner's Manual
Page 21
...INPUT B: XLR balanced mic input (1: ground, 2: hot, 3: cold). If you are supplying-either jack. Controls and Connectors 6 COMP knob (EMX512SC and EMX312SC only) This knob adjusts the level of compression applied to its ON position. We also recommend that you turn all output controls (LEVEL knobs, MASTER...before setting this switch to connect up a microphone or other power amplifiers and power speakers before operating the switch, to avoid risk of loud noises that the levels cannot be sure to turn the PHANTOM switch P to 11/12) These jacks accept stereo inputs....
...INPUT B: XLR balanced mic input (1: ground, 2: hot, 3: cold). If you are supplying-either jack. Controls and Connectors 6 COMP knob (EMX512SC and EMX312SC only) This knob adjusts the level of compression applied to its ON position. We also recommend that you turn all output controls (LEVEL knobs, MASTER...before setting this switch to connect up a microphone or other power amplifiers and power speakers before operating the switch, to avoid risk of loud noises that the levels cannot be sure to turn the PHANTOM switch P to 11/12) These jacks accept stereo inputs....
Owner's Manual
Page 25
... switch Selects the output that the mute has been turned on . S YS Processing switch This switch turns Yamaha Speaker Processing on when using phantom power, do not need phantom power. • When using one or more condenser microphones. The switch lights up to indicate that gets sent to...jacks on channels 1 to 11/12). EMX512SC/EMX312SC/EMX212S 25 NOTE When this switch off . The MAIN section's MASTER knob G adjusts the output level at all output controls (LEVEL knobs, MASTER knobs, etc.) to minimum settings before switching phantom power on channel pairs 5/6 to 4, and the ...
... switch Selects the output that the mute has been turned on . S YS Processing switch This switch turns Yamaha Speaker Processing on when using phantom power, do not need phantom power. • When using one or more condenser microphones. The switch lights up to indicate that gets sent to...jacks on channels 1 to 11/12). EMX512SC/EMX312SC/EMX212S 25 NOTE When this switch off . The MAIN section's MASTER knob G adjusts the output level at all output controls (LEVEL knobs, MASTER knobs, etc.) to minimum settings before switching phantom power on channel pairs 5/6 to 4, and the ...
Owner's Manual
Page 32
..., EFFECT OUT Residual Output Noise (20 Hz-20 kHz) MAIN OUT L, R - Specifications Specifications ■ General Specifications Output EMX512SC Maximum Output Power SPEAKERS OUT EMX312SC EMX212S RL Conditions 4 Ω 8 Ω 4 Ω Both ch drive, 1 kHz, 8 Ω THD+N =< 0.5% 4 Ω 8 Ω... at minimum. 4 Ω 0.5 % -115 dBu -50 -90 -90 dBu -65 Crosstalk @ 1 kHz It measures in each CH unit. Phantom Voltage It measures in each CH unit. Input CH1-4 Output CH 1-4 INPUT B, CH 5/6-11/12 MIC Output Adjacent CH inputs MAIN OUT - - Conditions...
..., EFFECT OUT Residual Output Noise (20 Hz-20 kHz) MAIN OUT L, R - Specifications Specifications ■ General Specifications Output EMX512SC Maximum Output Power SPEAKERS OUT EMX312SC EMX212S RL Conditions 4 Ω 8 Ω 4 Ω Both ch drive, 1 kHz, 8 Ω THD+N =< 0.5% 4 Ω 8 Ω... at minimum. 4 Ω 0.5 % -115 dBu -50 -90 -90 dBu -65 Crosstalk @ 1 kHz It measures in each CH unit. Phantom Voltage It measures in each CH unit. Input CH1-4 Output CH 1-4 INPUT B, CH 5/6-11/12 MIC Output Adjacent CH inputs MAIN OUT - - Conditions...