Whirlpool YGY397LXUQ Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool YGY397LXUQ manuals!
Problems with Whirlpool YGY397LXUQ?
Ask a Question
Free Whirlpool YGY397LXUQ manuals!
Problems with Whirlpool YGY397LXUQ?
Ask a Question
Most Recent Whirlpool YGY397LXUQ Questions
Control Panel On Ygy397lxuq04
Some of the control don't work. Bake, timer, warm, favorites, number 1-2-4-7 don't work. The rest of...
Some of the control don't work. Bake, timer, warm, favorites, number 1-2-4-7 don't work. The rest of...
(Posted by dianestnicolas 11 years ago)
Whirlpool YGY397LXUQ Videos
Whirlpool YGY397LXUQ Slide-In Range
Duration: :58
Total Views: 19
Duration: :58
Total Views: 19
Popular Whirlpool YGY397LXUQ Manual Pages
Installation Instructions - Page 2
... kill or hurt you don't follow instructions. All safety messages will follow instructions.
Connect anti-tip bracket to reduce the chance of others . We have provided many important safety messages in death or serious burns to potential hazards that can result in this manual and on your appliance. RANGE SAFETY
Your safety and the...
Installation Instructions - Page 3
...Part 280). Check existing electrical supply. The appliance wiring will not discolor, delaminate or sustain other damage. See "Electrical Connection" section. Given dimensions are shown must be installed. Model... driver ■ Hand or electric drill 3.2 mm) drill bit
Parts supplied Check that all electrical connections should be made by installing a range hood that all parts ...
Installation Instructions - Page 4
...and follow the range hood or microwave hood combination installation instructions for new branch-circuit installations (1996 NEC); Electrical Connection
To properly install your range, you must be revised so the... service technician if you will not slide all local codes and ordinances. The ground must conform with the ground connected to whether the appliance is located on the model/...
Installation Instructions - Page 5
...model/... a 50-amp rated cord with CSA Standard C22.1, Canadian Electrical Code, Part 1 - Be sure the wall receptacle is less than 30"...the appliance end must be at the point the power supply cord enters the appliance. Toronto, ON M9W 1R3 CANADA.
...edition, and all local codes and ordinances.
Canada Only
WARNING
■ Check with a qualified electrical installer if you have molded edge...
Installation Instructions - Page 6
...;₄" (36.2 cm)
6 Remove oven racks and parts package from the carton. Pull storage drawer out completely. 4. Remove and discard cardboard cross support. Connect anti-tip bracket to use a wrench or pliers...NOTE: If height adjustment is made when range is moved. INSTALLATION INSTRUCTIONS
Unpack Range
WARNING
Excessive Weight Hazard Use two or more people to engage the anti-tip bracket....
Installation Instructions - Page 7
...holes of the terminal block.
7 U.S.A.
Electrically ground range. See below. Failure to follow these instructions can result in death, fire, or electrical shock.
1. Anti-tip bracket
A. #12 x ...Disconnect power before servicing. Use a new 40 amp power supply cord. Electrical Shock Hazard Disconnect power before servicing. Failure to follow these instructions can result in...
Installation Instructions - Page 8
... and slide cord/conduit plate down and out. NUCQPTUROAUSSERRIEMWTADEOLIÓTCAVLNHOSAENEPTTELEOAUTÉCWGEIQCTR!EATUUCRRRESAICTCEESAOLORD
A.
NUCPQTUROAUSSERRIEMWTADEOLIÓTCAVLNHOSAENEPTTELEOAUTÉCWGEIQCTR!EATUUCRRRESAICTCEESAOLORD
■ Replace cord/conduit plate and insert screws.
8 Allow enough slack to easily attach the wiring to the terminal block.
■ Tighten strain...
Installation Instructions - Page 9
...If your home has:
And you will be cut out and removed. Part of metal ground strap must be attached first.
9 Discard C. Feed ... installation following instructions for : ■ New branch-circuit installations (1996 NEC) ■ Mobile homes ■ Recreational vehicles ■ In an area where local codes ...Replace back panel and screws on bottom of the ground-link under the screw.
3.
Installation Instructions - Page 10
...back 3" (7.6 cm) to the fuse disconnect or circuit breaker box. Replace terminal block access cover.
3-wire connection: Power Supply Cord
Use this ...-32 hex nut B.
Use ³⁄₈" nut driver to connect the neutral (white) wire to the outer ...-circuit installations (1996 NEC) ■ Mobile homes ■ Recreational vehicles ■ In an area where local codes prohibit ...
Installation Instructions - Page 11
... remove) the set screw to the terminal block - 20 lbs-in. (2.3 N-m)
Wire Awg
Torque
8 gauge copper
25 lbs-in. (2.8 N-m)
6 gauge aluminum
35 lbs-in following Bare Wire Torque Specifications chart.
Line ... metal ground strap must not contact any other terminal.
6. Use ³⁄₈" nut driver to connect the neutral (white) wire to the range with 10-32 hex nuts.
8.
Bare...
Installation Instructions - Page 12
...
Torque
8 gauge copper 6 gauge aluminum
25 lbs-in. (2.8 N-m) 35 lbs-in following Bare Wire Torque Specifications chart. Line 2 (red) F.
Line 1 (black) wire
D. Line 2 (red) wire
Bare Wire Torque Specifications Attaching terminal lugs to side;
Securely tighten set screw on rack and check levelness of the 10-32 hex nuts. Ground-link screw
D. Place...
Installation Instructions - Page 13
... all parts are not bent. 8. Complete cleaning or maintenance. 4. Replace storage drawer. 9. Moving the Range
WARNING
Tip Over Hazard A child or adult can result in power supply cord. 5.
Unplug the power supply cord. 3. Check that all packaging materials. 4. Check that the range is installed:
■ Look for specific instruction on . Failure to follow these instructions can...
Whirlpool YGY397LXUQ Reviews
We have not received any reviews for Whirlpool yet.