Whirlpool WED72HEDW Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WED72HEDW manuals!
Problems with Whirlpool WED72HEDW?
Ask a Question
Free Whirlpool WED72HEDW manuals!
Problems with Whirlpool WED72HEDW?
Ask a Question
Most Recent Whirlpool WED72HEDW Questions
Dryer Cuts Off
The dryer gets really hot to the touch and the vent line is clear, why is the dryer cutting off
The dryer gets really hot to the touch and the vent line is clear, why is the dryer cutting off
(Posted by Tjburns5 8 years ago)
My Whirlpool Dryer Will Not Go To High Temp
my whirlpool dryer model WED72HEDW will not go to high temp even with the ecoboost disabled. I've tr...
my whirlpool dryer model WED72HEDW will not go to high temp even with the ecoboost disabled. I've tr...
(Posted by chayward 8 years ago)
Can I See The Back Of The Machine?
back of machine large photo WED72HEDW dryer and pedestal
back of machine large photo WED72HEDW dryer and pedestal
(Posted by tft128 9 years ago)
Popular Whirlpool WED72HEDW Manual Pages
Use & Care Guide - Page 4
In Canada, call 1-800-901-2042, or visit us at www.whirlpoolparts.ca
15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, call 1-800-807-6777 or visit us at a premium, the stack kit allows the dryer to a more information. Stack Kit If space is at : www.whirlpool.com/accessories. For more information on top...
Use & Care Guide - Page 5
... knits, and synthetics.
5 Tips for getting the best performance from the dryer. n Replace plastic or foil vent material
with heat, dryers require good airflow to the dryer plays a big role in a vent system; each load. Use the NORMAL dryness level to provide the most energy savings and enhanced fabric care from your energy savings. n Use the shortest length of...
Use & Care Guide - Page 7
... dry.
Use the warmest setting safe for your energy savings by minutes.
Damp Dry Signal (on some models) to add a short steam cycle after about one second to turn on the EcoBoost™ option.
The light will display "Lc" or "Loc." 1 POWER Touch to turn the dryer on and off the EcoBoost™ option. Automatic Cycles...
Use & Care Guide - Page 8
... Medium to Low for all features and cycles are available on all models.
This is the preferred energy cycle.
If there is a power failure, settings will sound to indicate when it is a long cycle with High and Medium Drying Temperature settings.
* On steam models only.
This cycle is a high heat cycle. Cycle Guide - If settings are default settings for...
Use & Care Guide - Page 9
... drying heavyweight items such as sheets, blouses, dresses, underwear, permanent press fabrics, and some models, you are designed for items that cycle.
Cycle Guide - Manual Cycles
Settings and options shown in your load. If settings are available on the type of the temperature to increase or decrease the time in 5-minute increments. If there is...
Use & Care Guide - Page 11
...Steam, EcoBoost, or Static Reduce. NOTE: Not all options and settings are available with all cycles.
There are 5 drying settings (setting codes differ depending on model), which the dryer will affect all models. ...30% more dry than you would like, you may adjust different settings, depending on whether you select a Manual Cycle, the time appears in dry loads. Touch and hold DRYNESS ...
Use & Care Guide - Page 12
... the inside of airflow through the dryer and dryer vent system for the entire cycle. To use . Rest the rear support on if a blocked vent or low airflow issue is detected. be cleared...dryer's life. See "Troubleshooting" section.
Eco Monitor The Eco Monitor allows you to see "Check Your Vent System for up or iron while still damp may be removed.
Wet The load is available during Manual...
Use & Care Guide - Page 15
.... Replace the fuses or reset the circuit breaker. Electric dryers require 240-volt power supply. Water pump or water inlet valve (depending on model) on the EcoBoost™ option.
Load is packed tightly or exhaust vent is normal.
The dryer may be in "Cycle Guide."
Reduce load size to possibly avoid a service call. For optimal energy, turn off the EcoBoost...
Use & Care Guide - Page 17
... portion of cycle complete. "L2" Diagnostic Code (low or no line voltage condition)
There may be a problem with a lower heat setting to run cleaned. NOTE: This error will continue to avoid overdrying the load. Try the following :
• Clean lint screen.
• Check to restart the dryer. Refer to the Installation Instructions for assistance and to the wall...
Use & Care Guide - Page 18
... instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will be provided by our authorized Whirlpool Service Providers. gas or reversal of inaccessible appliances or built-in which it was purchased, or at its sole discretion replace the product. Damage from the date of the Use and Care Guide, scan the QR code...
Installation Guide - Page 1
... Connection 10 VENTING 12 Venting Requirements 12 Plan Vent System 13 Install Vent System 15 CONNECT INLET HOSE (STEAM MODEL ONLY 15 CONNECT VENT 16 LEVEL DRYER 17 COMPLETE INSTALLATION CHECKLIST 17 DOOR REVERSAL (OPTIONAL 18
Para una version de estas instrucciones en español, visite www.Whirlpool.com
INSTALLATION NOTES Date of purchase Date of installation Installer Model number...
Installation Guide - Page 4
... temperatures may use the water supply for your washer using a pedestal, you will need to bottom of dryer.
■■The dryer must support dryer weight of installation and servicing; Contact your local building inspector. See "Venting Requirements."
3/4"* (18 mm)
* Approx. Some codes limit, or do not permit, installation of dryer to water, weather, or at temperatures below 40...
Installation Guide - Page 14
... be converted to have the dryer converted.
Standard rear offset exhaust installation B. or right-side exhaust installation C. To find your local dealer to exhaust out the right side, left side (all other models, refer to use of vent
Angled hoods
0
Rigid metal
160 ft. (48.8 m)
1
Rigid metal
150 ft. (45.7 m)
2
Rigid metal
140 ft. (42.7 m)
3
Rigid metal
130...
Installation Guide - Page 16
... result.
6. Attach other end of long hose to final location
Check that vent is clean. If connecting to existing vent, make sure vent is secured to crush or kink vent. Move dryer to fill valve at bottom of dryer back panel. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check for leaks around "Y" connector, faucet...
Installation Guide - Page 17
...
Not Level
COMPLETE INSTALLATION CHECKLIST
q Check that dryer is plugged into a grounded
outlet. q Check that all four legs are set in a hard water area, use wrench to back.
q Select a Time Dry heated cycle, and start of dryer from front to adjust legs up or down, and check again for certain part replacement or repair. This odor is...
Whirlpool WED72HEDW Reviews
We have not received any reviews for Whirlpool yet.