Whirlpool WGD9400SW - Duet HT Series Gas Dryer Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WGD9400SW manuals!
Problems with Whirlpool WGD9400SW?
Ask a Question
Free Whirlpool WGD9400SW manuals!
Problems with Whirlpool WGD9400SW?
Ask a Question
Most Recent Whirlpool WGD9400SW Questions
Dryer Stopped Working
Our dryer was making a grinding sound and then it just stopped
Our dryer was making a grinding sound and then it just stopped
(Posted by Anonymous-29155 12 years ago)
Getting Code F 22 During The Drying Cycle
(Posted by tomd16duckworth 13 years ago)
Popular Whirlpool WGD9400SW Manual Pages
Use and Care Guide - Page 2
... at least 9" (229 mm) above the floor. Accessory
Stack Kit
Door Reversal Kit
Door Reversal and Stack Combination Kit
Back Guard
Optional Exhaust Installation Dryer can write to the total height of the dryer for this dryer. ASSISTANCE OR SERVICE
Before calling for Part Number.
In the U.S.A. Whirlpool designated service technicians are trained to fulfill the product warranty and provide...
Use and Care Guide - Page 3
... if you what can kill or hurt you and others are not followed.
3 All safety messages will follow instructions. DRYER SAFETY
Your safety and the safety of injury, and tell you what the potential hazard is the safety alert ...the chance of others . We have provided many important safety messages in this manual and on your appliance.
This symbol alerts you don't follow instructions.
Use and Care Guide - Page 4
Follow the gas supplier's
instructions.
• If you smell gas" instructions.
4 Installation and service must be detected by a qualified installer, service agency, or the gas supplier.
IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70.
For more information, contact your gas supplier from...
Use and Care Guide - Page 5
... Massachusetts, the following installation, see the QUICK START GUIDE on it (even after washing). Failure to use your dryer following installation instructions apply:
■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by using a ball valve, it shall be a T-handle type. ■ A flexible gas connector, when...
Use and Care Guide - Page 7
... cause temporary staining on all models.
Steam models
Non-Steam models
Cycle Control knob
Automatic Cycles Automatic Cycles allow you are drying.
This cycle should be sanitized. Manual Preset Cycle Settings
Manual Cycles Load Type
Temperature Est. See the following Automatic Preset Cycle Settings chart. Under certain environmental or installation conditions, you are available on...
Use and Care Guide - Page 8
... smooth out
wrinkles in loads left open the door to stop the dryer, rearrange the load inside the dryer, close the door and restart the dryer to "ON." This is set to remove a load of the beeps. shower...selected.)
Damp Dry Signal On some models, the Damp Dry Signal may be emitted every 5 minutes until pressed again, the door is opened and closed, or the door is finished. NOTE: When the ...
Use and Care Guide - Page 9
... adapt to stop before your load is in the door opening of your Auto Dry cycles. The dryer will beep, and "CF" will become your new preset drying setting for your clothes, or cause the dryer to different installations, environmental conditions or personal preference. The drying setting you selected will be accepted.
To wash
1. To unlock...
Use and Care Guide - Page 10
... dryers: 1. Transport hose separately. 4. Reinstalling the dryer
Follow the "Installation Instructions" to dry drum. Wet a nylon brush with a damp cloth. 4. Tumble a load of use dryer again
1. Turn off water faucet. 3. Failure to the dryer. Shut off the water supply to do so can result in the hoses, freezing can damage your dryer for Steam Models
Water Inlet Hoses
Replace...
Use and Care Guide - Page 11
....
3.
Large loads may be a problem with a qualified electrician.
■ Was a regular fuse used for a while, there may require pressing and holding the Start button for details. Check with your Installation Instructions. Check the front and rear edges of a service call... Press and hold START to restart the dryer.
■ "L2" Diagnostic Code (low or no line voltage...
Use and Care Guide - Page 12
...; Confirm your vent system falls within the recommended run cleaned.
■ "E" Variable (E1, E2, E3) service codes: Call for service.
See the Installation Instructions. Check that water inlet hose is connected to both the faucet and dryer's water inlet valve. Dryer Results
Clothes are not drying satisfactorily, drying times are gone from loads consisting of 1-4 garments. Use...
Use and Care Guide - Page 13
... also may not apply to province. Pick up and delivery. Replacement parts or repair labor on the duration of implied warranties of original purchase date is required to obtain service under this major appliance is inconsistent to published user or operator instructions and/or installation instructions.
2. DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY...
Whirlpool WGD9400SW Reviews
We have not received any reviews for Whirlpool yet.