Dimension Guide
Page 1
...*NOTE: 24" (61 cm) min. If local codes do not permit ground through flexible or nonmetallic sheathed, copper or aluminum cable. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to 22" (55.9 cm) from floor F 2.2 cm)... clearance to the cabinet. For complete details, see NOTE*. The model/serial number rating plate is recommended. Model/serial rating plate (located on the oven frame behind storage drawer panel) *Range can be connected to the proper electrical voltage and frequency as specified on the model...
...*NOTE: 24" (61 cm) min. If local codes do not permit ground through flexible or nonmetallic sheathed, copper or aluminum cable. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to 22" (55.9 cm) from floor F 2.2 cm)... clearance to the cabinet. For complete details, see NOTE*. The model/serial number rating plate is recommended. Model/serial rating plate (located on the oven frame behind storage drawer panel) *Range can be connected to the proper electrical voltage and frequency as specified on the model...
Installation Instructions
Page 3
... hardware store. IMPORTANT: To avoid damage to make sure that all electrical connections be avoided. Any method of securing the range is located on the model/serial rating plate. See "Electrical Connection" section. 3 Longer screws are shown must end in the kitchen. ■ To eliminate ...■ ¼" nut driver and nut driver 3.2 mm) drill bit (for wood floors) 4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors) ■ Tin snips or large wire cutters (for convenient use the Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280)....
... hardware store. IMPORTANT: To avoid damage to make sure that all electrical connections be avoided. Any method of securing the range is located on the model/serial rating plate. See "Electrical Connection" section. 3 Longer screws are shown must end in the kitchen. ■ To eliminate ...■ ¼" nut driver and nut driver 3.2 mm) drill bit (for wood floors) 4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors) ■ Tin snips or large wire cutters (for convenient use the Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280)....
Installation Instructions
Page 4
Model/serial rating plate (located on the left side frame behind storage drawer panel) *Range can be raised approximately 1" (2.5 cm) by a qualified electrician. 4 upper cabinet depth B. 30" (76.2 cm) min. For minimum clearance to combustible walls with... height. D. 30¹⁄₈" (76.5 cm) min. from either cabinet, 5¹⁄₂" (14.0 cm) max. Check with zero clearance. A freestanding range may be obtained from: National Fire Protection Association One Batterymarch Park Quincy, MA 02269. opening width C. required between cutout and cabinet door or hinge. *NOTE...
Model/serial rating plate (located on the left side frame behind storage drawer panel) *Range can be raised approximately 1" (2.5 cm) by a qualified electrician. 4 upper cabinet depth B. 30" (76.2 cm) min. For minimum clearance to combustible walls with... height. D. 30¹⁄₈" (76.5 cm) min. from either cabinet, 5¹⁄₂" (14.0 cm) max. Check with zero clearance. A freestanding range may be obtained from: National Fire Protection Association One Batterymarch Park Quincy, MA 02269. opening width C. required between cutout and cabinet door or hinge. *NOTE...
Installation Instructions
Page 5
... If connecting to a 3-wire system: Local codes may permit the use a 50-amp rated cord with ranges. If local codes do not permit ground through the neutral conductor. If connecting to a 4-wire system: This range is located behind the control panel or on the oven frame behind the storage drawer panel...spade terminals with upturned ends, terminating in the line so that specify use with kit. or 50-amp power supply cord (pigtail) (see following Range Rating chart). Cord should be Type SRD or SRDT with a UL listed strain relief and be revised so the green ground wire of the 4-wire ...
... If connecting to a 3-wire system: Local codes may permit the use a 50-amp rated cord with ranges. If local codes do not permit ground through the neutral conductor. If connecting to a 4-wire system: This range is located behind the control panel or on the oven frame behind the storage drawer panel...spade terminals with upturned ends, terminating in the line so that specify use with kit. or 50-amp power supply cord (pigtail) (see following Range Rating chart). Cord should be Type SRD or SRDT with a UL listed strain relief and be revised so the green ground wire of the 4-wire ...
Installation Instructions
Page 9
...cover. 9 Line 2 (red) D D. Ground-link screw D. D B C A. 10-32 hex nut B. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening 2. 3. Securely tighten... to connect the green ground wire from the power supply cord to the center terminal block post with ranges. 5. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄...
...cover. 9 Line 2 (red) D D. Ground-link screw D. D B C A. 10-32 hex nut B. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening 2. 3. Securely tighten... to connect the green ground wire from the power supply cord to the center terminal block post with ranges. 5. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄...