URC MRF-300 Support and Manuals
Get Help and Manuals for this URC item
Popular URC MRF-300 Manual Pages
Owners Manual - Page 1
MRF-300/RFX150 INSTALLATION
MANUAL
Multi-Zone RF Base Station for the MX-3000, the AuroraTM, the AerosTM, the OmegaTM and the OsirisTM remote controls.
Owners Manual - Page 2
...part of this manual may be subject to change without prior written consent from Universal Remote Control, Inc. SHALL NOT BE LIABLE FOR OPERATIONAL,TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. UNIVERSAL REMOTE CONTROL, INC. The information in this manual may be copied or reproduced in this manual...Fax: (914) 835-4532 MRF-300 Installation Manual ©2005 Universal Remote ...
Owners Manual - Page 3
Step by Step
8
Programming For Multiple Equipment Locations
11
Frequently Asked Questions
12
Warranty
12
Specifications
12 Step by Step
7
Controlling An Array of Identical Components or Zones
8
Identical Components/Zones - TABLE OF CONTENTS
Introduction
1
Features and Benefits
2
Parts Guide
2
Installation
3
Front Blaster Overload
7
Disabling the Front Blaster -
Owners Manual - Page 4
... sensors on the front panels of the MRF300's Front Blaster.
Page 1 URC "Addressable" remote controls send radio waves in to the MRF-300's rear flasher line outputs via its adjustable IR Line Outputs. The Flashers relay commands to components out of sight of your components. MRF-300 BASE STATION
Introduction
The MRF-300 base station is only compatible with Universal Remote Control...
Owners Manual - Page 5
.... Parts Guide
The MRF-300 RF Base Station includes:
1 - Screws for wall mounting the MRF-300 4 -
RF Adjustment Tool (Screwdriver for expansion) 1 - Expand Range by installing a base station at each output can be programmed to all IR line outputs (does not support IR routing).The 5V, 100 milliamp output will relay IR Data from IR repeaters or MultiZone Keypads to specifically control...
Owners Manual - Page 6
...). Use a small flat blade screwdriver to set to the address you leave it set when programming the remote control. Page 3
Mount or place the MRF-300 conveniently and run flashers to each component's front panel sensor or connect the Line Out to reveal the RF ID# rotary switch.
Step 2 - b. MRF-300 BASE STATION
Installation
Step 1 - Slide off the mounting plate...
Owners Manual - Page 7
... DO NOT MOUNT IT!
Simply connect the RF OUT of the first to the RF IN of the Plug). MRF-300 BASE STATION
Copper colored conductor is GROUND (Sleeve of the next MRF-300.
RF OUT of the first MRF-300 to the RF IN of the next and so on both ends to One RFX-150 RF Sensor
Use the cable with 3.5 mm...
Owners Manual - Page 8
... be connected via the RF Range attenuator screw on both the RFX-150 and the MRF-300 should light up to the MRF-300. MRF-300 BASE STATION
Step 4 - The POWER LED's on the RFX-150. Place the RFX150 in another RFX-150 RF Sensor in normal conditions.
Mount the RFX-150 and adjust for RF Interference
The RF LED lights when any RF signal is unreliable...
Owners Manual - Page 9
... levels for best operation. Reprogram the remote control to IR overload or saturation. Page 6 MRF-300 BASE STATION Step 7 - NOTE: TiVo, Replay TV, Satellite Receivers and Cable Boxes are sent to all extremely sensitive to send IR commands only via a specific (1-6) Line Output, then readjust the IR Line Output level. Step 8 - Adjust IR Line Output...
Owners Manual - Page 10
... you can control to the remote control. Open your changes using File|Save and DOWNLOAD to six. MRF-300 BASE STATION
Front Blaster Overload
A few models of components your change. This will appear.
Setup the Receiver Extend the RF Setup window by clicking on OK to apply your MRF-300 can purchase an additional MRF-300.
Next, click on the Receivers button.
Owners Manual - Page 11
... identical devices to operate one of the fifteen unique IR Routing addresses.
2.
MRF-300 BASE STATION
Controlling An Array of Identical Components or Zones
There are several considerations to take into account when you are installing an MRF-300 to control an array of identical components:
1.The RF ID# cannot be set to RF ONLY for each of the TV's.
Owners Manual - Page 12
... if you are not using it, you can see that the factory default programming sets all of the devices to ALL of your work. From the context menu that is... Step 6 - Repeat this PASTE on the intersection of the other identical device. The RF Setup window is NOT PROGRAMMED. MRF-300 BASE STATION
Step 3 - From the context menu that the default sends IR commands for identical components...
Owners Manual - Page 13
... correct Flasher (refer to your identical TV's!
Adjust the Flashers For Each of the system set to ALL. When you to adjust which Flashers output by the
remote control for each device...may leave the other components of the RF Setup window. Signal Column
TV1 Device Row
Select RF from the seven options shown in
the pull down list box. MRF-300 BASE STATION
Click on the "cell" for the...
Owners Manual - Page 14
... receiver to
install multiple MRF-300's in MX Editor The RF Setup window opens after selecting RF Control from the pull down list. It is ok to something more descriptive by clicking on the Rename button. Reveal the Receiver settings Extend the RF Setup window by clicking on the Receivers button of the RF setup window.
Step 3 - Open the RF Setup Window in...
Owners Manual - Page 15
... the range you need, consider installing additional RFX-150 RF Sensors in the system to connect to the selected TV also responds.
Second, check that an opaque material like electrical tape is used to a specific IR Line Output instead of them, the TV next to the MRF-300? I've correctly set on both the remote control and...
URC MRF-300 Reviews
We have not received any reviews for URC yet.