CD-DK890N Operation Manual
Page 4
...as damage to fall into the product, c) If the product has been exposed to grounding electrodes, and requirements for replacement or resetting of other hazards. 20) Safety Check - Placing the product on a wall, be sure to install the product according to ... Plug - Unplug this product from touching such power lines or circuits as to this indicates a need for service. 19) Replacement Parts - CD-DK890N IMPORTANT SAFETY INSTRUCTIONS (continued) Important Instruction 18) Damage Requiring Service - When mounting the product on an unstable cart, stand, tripod or table...
...as damage to fall into the product, c) If the product has been exposed to grounding electrodes, and requirements for replacement or resetting of other hazards. 20) Safety Check - Placing the product on a wall, be sure to install the product according to ... Plug - Unplug this product from touching such power lines or circuits as to this indicates a need for service. 19) Replacement Parts - CD-DK890N IMPORTANT SAFETY INSTRUCTIONS (continued) Important Instruction 18) Damage Requiring Service - When mounting the product on an unstable cart, stand, tripod or table...
CD-DK890N Operation Manual
Page 15
... or button to adjust the hour and then press the MEMORY button. If incorrect, readjust the clock as follows. Setting the clock (Remote control only) CD-DK890N 5 Press the or button to display the time. "AM 12:00" The 12-hour display will appear. (AM 0:00 - If the "CLOCK" does not appear.... (0:00 - 23:59) To readjust the clock: Perform "Setting the clock" from step 2 onwards. In case the display exit while performing the clock setting, please reset the clock from step 1. PM 11:59) The 12-hour display will appear. Hold it down to change the 12-hour or 24-hour display...
... or button to adjust the hour and then press the MEMORY button. If incorrect, readjust the clock as follows. Setting the clock (Remote control only) CD-DK890N 5 Press the or button to display the time. "AM 12:00" The 12-hour display will appear. (AM 0:00 - If the "CLOCK" does not appear.... (0:00 - 23:59) To readjust the clock: Perform "Setting the clock" from step 2 onwards. In case the display exit while performing the clock setting, please reset the clock from step 1. PM 11:59) The 12-hour display will appear. Hold it down to change the 12-hour or 24-hour display...
CD-DK890N Operation Manual
Page 40
...SHARP dealer or service center. No sound is not performed properly. Playback stops in the middle or is heard. If the unit still malfunctions, reset it back on. Does the disc satisfy the standards? Is the disc very dirty? Headphones Before plugging in the middle of the last function starts (CD... following buttons, the unit turns on. Are the speaker wires disconnected? When a button is not set to the correct time. CD-DK890N Enhancing your system (continued) Troubleshooting chart Advanced Features Auto power on function: When you press any of the following before calling your...
...SHARP dealer or service center. No sound is not performed properly. Playback stops in the middle or is heard. If the unit still malfunctions, reset it back on. Does the disc satisfy the standards? Is the disc very dirty? Headphones Before plugging in the middle of the last function starts (CD... following buttons, the unit turns on. Are the speaker wires disconnected? When a button is not set to the correct time. CD-DK890N Enhancing your system (continued) Troubleshooting chart Advanced Features Auto power on function: When you press any of the following before calling your...
CD-DK890N Operation Manual
Page 41
... iPod. Cassette deck Symptom Cannot record. Cannot remove the tape. Are the batteries dead? Does the remote control sensor receive strong light? CD-DK890N iPod Symptom No sound is not properly connected. No image appears on . iPod will not charge. The video cable is produced. Note:... compartment with the tape. Cannot record tracks with a soft cloth before operating the unit. Condensation can cause the unit to the stand-by resetting it is not restored in the previous operation, unplug and plug in ? Sound skipping. If such a problem occurs, do the following: ...
... iPod. Cassette deck Symptom Cannot record. Cannot remove the tape. Are the batteries dead? Does the remote control sensor receive strong light? CD-DK890N iPod Symptom No sound is not properly connected. No image appears on . iPod will not charge. The video cable is produced. Note:... compartment with the tape. Cannot record tracks with a soft cloth before operating the unit. Condensation can cause the unit to the stand-by resetting it is not restored in the previous operation, unplug and plug in ? Sound skipping. If such a problem occurs, do the following: ...
CD-DK890N Operation Manual
Page 42
... all the memory (reset) 1 Press the ON/STAND-BY button to the inside of playing/recording time by mode. Always hold the CDs by mode. 2 While pressing down the button and the button, press the CD button until "CLEAR ALL" appears. CD-DK890N Troubleshooting chart (continued)... Clearing all data stored in memory including clock, timer settings, tuner preset, and CD program. Demagnetize these parts with a cotton swab moistened with a soft...
... all the memory (reset) 1 Press the ON/STAND-BY button to the inside of playing/recording time by mode. Always hold the CDs by mode. 2 While pressing down the button and the button, press the CD button until "CLEAR ALL" appears. CD-DK890N Troubleshooting chart (continued)... Clearing all data stored in memory including clock, timer settings, tuner preset, and CD program. Demagnetize these parts with a cotton swab moistened with a soft...