Ryobi TS1144 Support and Manuals
Get Help and Manuals for this Ryobi item
This item is in your list!
View All Support Options Below
Free Ryobi TS1144 manuals!
Problems with Ryobi TS1144?
Ask a Question
Free Ryobi TS1144 manuals!
Problems with Ryobi TS1144?
Ask a Question
Popular Ryobi TS1144 Manual Pages
Operation Manual - Page 3
...repaired before cutting. Many accidents are caused by a qualified repair person using only identical replacement parts...serviced by poorly maintained power tools.
Keep cutting tools sharp and clean. The proximity of the spinning saw blade, there is set correctly to support...not use . Supporting the workpiece "cross handed" i.e. MITER SAW SPECIFIC SAFETY RULES
...
Operation Manual - Page 4
... moving parts to be jammed or pressed by a qualified service technician ...support. Wait for a table extension or as the specific potential hazards related to instruct other ). The braking action of power and overheating. To reduce the risk of the workpiece being cut or when releasing the switch before the saw may to stop before contacting the workpiece. Rods have repaired...
Operation Manual - Page 5
...use .
Double check all setups. Never use to avoid serious personal injury...blade or other moving workpiece or changing settings.
• Disconnect the saw . Lock...work surface before changing blade or servicing.
Always carry the ...or have damaged, missing, or failed parts replaced before resuming operation.
Always ... must read the operator's manual.
• Wear eye ...
Operation Manual - Page 13
...not included) are needed for making adjustments or installing the blade:
SQUARE
COMBINATION SQUARE
Fig. 6
LOOSE PARTS LIST
The following items are included with the... tool:
Miter Saw Miter Lock Knob
Dust Bag Work Clamp
DUST BAG
WORK CLAMP
MITER LOCK KNOB
Blade Wrench Operator's Manual...
Operation Manual - Page 14
enced the settings, refer to specific procedures explained later in personal injury. WARNING:
Do not use with the saw arm secured in accidental starting and possible serious personal injury.
WARNING:
If any parts are not assembled to make sure no breakage or damage occurred during operation of the tie wrap.
Inspect the tool...
Operation Manual - Page 15
...check the workbench after mounting to a work surface before operating. To install the miter lock knob, place the threaded stud on the end ...result in serious personal injury. Failure to heed this saw to a firm supporting surface such as a workbench, mounting board, or miter saw .
Tighten...used, read operator's manual and follow the instructions for mounting to a workbench is noted, secure the workbench...
Operation Manual - Page 18
... the miter table.
Loosen bevel lock knob and set 90° to the table. Place one -half turn
and press... portions of the square against the flat part of the saw blade. ASSEMBLY
REMOVING/REPLACING THE THROAT PLATE
See Figure 15.
If...manual show points being careful not to overtighten which could result in the saw without a throat plate installed. English
Operation Manual - Page 20
...
stop . Place a combination square against the miter table and the flat part of the square and the saw blade should be used to miter table). NOTE: Make sure that ... and reset them to -table alignment. Tighten bevel lock knob at 0° bevel (blade set saw blade. COMBINATION SQUARE
Retighten bevel lock knob.
COMBINATION SQUARE
BLADE
MITER TABLE
VIEW OF...
Operation Manual - Page 22
... the stock with a roller stand or with the miter table set at some angle other suitable clamp to secure the workpiece when possible...
When cutting long pieces of lumber or molding, support the opposite end of the cutting operation just to stop rotating...switch trigger and allow the blade to make sure that no problems will seat itself in the miter table base. OPERATION
TO ...
Operation Manual - Page 23
... workpiece.
Release the switch trigger and allow the saw blade to make sure that no problems will seat itself in the miter table base.
Loosen the bevel lock knob and move... set at an angle between 0° and 45°. Depress the trigger lockout lever and squeeze the switch trigger.
See figures 32 - 33.
When cutting long pieces of lumber or molding, support...
Operation Manual - Page 24
...must be checked after setting the second angle, since adjusting the second angle affects the first. See figures 32 - 33.
When cutting long pieces of lumber or molding, support the opposite end ... the two angle settings. The first angle setting should always be taken when making compound miter setups due to the interaction of the bevel setting. NOTE: You can be set at the same ...
Operation Manual - Page 25
... and through the workpiece.
Release the switch trigger and allow the saw blade to make sure that no problems will occur when the cut is made.
Grasp the saw handle firmly.
Supports, roller stand, or work surface level with one hand and secure it does not sag. LONG WORKPIECE
WORKPIECE...
Operation Manual - Page 29
...POSITIVE STOP ADJUSTMENTS
See Figure 34.
Failure to heed this manual.
If the blade is out of this warning ...by at your nearest authorized service center. To adjust:
Unplug the saw repaired at your nearest authorized service center. NOTE: The ... any readjustments that are necessary and periodically check the parts alignment to make sure the tool is unplugged from the...
Parts Diagram - Page 3
...1 Screw (M4.2 x 13 mm 5 Handle Assembly 1 Cord Clamp 1 Bend Relief 1 Power Cord (Inc. TS1144
The model number will be found on a label attached to the motor housing. RYOBI 7-1/4 in . Key Nos. 14 & 19 1
KEY PART
NO. PART
NUMBER
DESCRIPTION
QTY
1
089240011011
2
089240027020
3
089240011010
4
089240027022
5
089240011017
6
089240011075
7
089240011904
8
089240027705...
Parts Diagram - Page 5
... 1 Spring Washer 1 Plate Screw 1
NOT SHOWN: 995000692 3-15-19 (Rev:01)
Operator's Manual (089240034904)
5 RYOBI 7-1/4 in .
Key No. 21 1 Spanner Holder 1 Screw (M6 x 25 mm 4 Hex Key Wrench 1 Rubber Feet 10 Screw (M6 x 16 mm 1 Miter Table Assembly (Inc. TS1144
The model number will be found on a label attached to the motor housing. COMPOUND...
Ryobi TS1144 Reviews
Do you have an experience with the Ryobi TS1144 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Ryobi yet.
Earn 750 points for your review!