Ryobi P730 Support and Manuals
Get Help and Manuals for this Ryobi item
Most Recent Ryobi P730 Questions
Ryobi P730 Pressure Hose Replacement
how do I replace the pressure hose? I have taken all the screws holding the case together and the ca...
how do I replace the pressure hose? I have taken all the screws holding the case together and the ca...
(Posted by benybarra 7 years ago)
Ryobi P 730 Reset Problems
RYOBI P730 air compressor will not reset to 0 and will not run with trigger. The display show 655 ps...
RYOBI P730 air compressor will not reset to 0 and will not run with trigger. The display show 655 ps...
(Posted by deevans 12 years ago)
Popular Ryobi P730 Manual Pages
English Manual - Page 1
... will give you for dependability, ease of injury, the user must read and understand the operator's manual before using
this product. Thank you years of rugged, trouble-free performance.
OPERATOR'S MANUAL
18 volt inflator DIGITAL GAUGE
P730
BATTERIES AND CHARGERS SOLD
SEPERATELY
Your inflator has been engineered and manufactured to our high standard for your purchase.
English Manual - Page 3
... or off . away from moving parts.
Keep your model. Do not wear loose clothing or jewelry. Stable footing on or off position before each use if defect is designed.
Check hoses for which could restrict the flow of fresh air to lose control.
Operate inflator in moving parts, breakage of children and other condition...
English Manual - Page 4
...or puncture. Follow instructions in the system. Protect material lines and air lines from oil and grease. SPECIFIC SAFETY RULES
Know your inflator, in a risk of serious personal injury.
Do not use only identical replacement parts. Your lungs can cause injury to spray chemicals. A damaged battery is dusty.
SERVICE
Inflator service must be...
English Manual - Page 5
... damage.
Do not use this manual, on charger. Refer to the charger and battery, charge only nickel-cadmium rechargeable batteries as those of extension cord are the same number, size and shape as specifically designated on , tripped over, come in contact with plastic parts. IMPORTANT SAFETY INSTRUCTIONS
1. CAUTION: To reduce the risk of...
English Manual - Page 7
... and instructions in severe eye damage.
SAVE THESE INSTRUCTIONS
...SERVICE CENTER for repair.
SERVICE
Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you read thoroughly and understand completely the operator's manual. Call Ryobi customer service for use only identical replacement parts...
English Manual - Page 8
... safe use of applications.
lock-on button
The lock-on button is convenient for continuous inflating for extended periods of the inflator that instantly stops the inflator during operation.
HIGH PRESSURE HOSE
The high pressure hose can be used to set pressure type.
Low Pressure Hose Length 14 in . FEATURES
PRODUCT SPECIFICATIONS Motor 18 Volt DC High Pressure...
English Manual - Page 9
...sufficient to make you have carefully inspected and satisfactorily operated the inflator.
n Carefully remove the inflator and any parts are replaced.
WARNING:
Do not use . Driving a vehicle with this inflator. Return the charger and battery to be inflated unattended while inflator is not designed for service or replacement.
n Do not discard the packing material until the...
English Manual - Page 10
.... This indicates the charger is normal and does not indicate a problem. Do not place the charger and battery pack in ...replacing. When the battery pack reaches normal voltage range, the red LED should come on the battery pack to the touch while charging. Note: This situation only occurs when continuous use of the inflator causes the batteries to your nearest Authorized Service...
English Manual - Page 11
...the inflator. WARNING:
Improperly attached hoses or adaptors can cause faulty pressure readings. END CAP REMOVAL
See Figure 5. The inflator has two hoses for inflating high pressure items like air ...REMOVE
HIGH PRESSURE
HOSE
LATCHES Fig. 4
Fig. 5
LOW PRESSURE
HOSE
11
Fig. 6 To replace endcap, push endcap tabs into place properly.
Improper installation of inflation.
Make sure ...
English Manual - Page 14
....
Release the switch trigger and the inflator will appear on by holding the trigger in place. INFLATING MANUALLY FOR HIGH AND LOW PRESSURE APPLICATIONS
Connect either high or low pressure hose to item to select the desired measuring unit. The setting takes effect after inflation, press the ( + ) or ( - ) button.
If gauge reads...
English Manual - Page 15
....
Nickel-cadmium batteries must be repaired or replaced by their use only identical replacement parts. Local, state or federal laws may be replaced at any other parts may result.
If operation is fully
charged and ready for this inflator is below
80°F. Store battery packs in ordinary trash. MAINTENANCE
WARNING:
When servicing, use . NOTE: Use only...
English Manual - Page 16
... Ryobi ...Service Center.
OPERATOR'S MANUAL
18 volt inflator DIGITAL GAUGE
P730
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to these chemicals: work in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
• MODEL NUMBER
P730...
Repair Sheet - Page 3
... number in all correspondence regarding your INFLATOR or when ordering repair parts. May Be Purchased Locally
MODEL NUMBER P730
The model number will be found on a plate attached to the motor housing. PART NUMBER
1
200467001
2
342210001
3
660252001
4
660203003
5
514195001
6
570082001
7
514212001
8
514201001
9
513623001
10
514208001
11
514196001
12
6620311
13...
Repair Sheet - Page 4
...
QTY
GEAR CASE COVER ASSEMBLY WITH BEARINGS 1 GEAR SHAFT ASSEMBLY 1 MOTOR ASSEMBLY 1 HIGH PRESSURE HOSE ASSEMBLY 1 VALVE 1 COMPRESSION SPRING 1 WASHER 1
* Standard Hardware Item - Always mention the model number in all correspondence regarding your INFLATOR or when ordering repair parts. MODEL NUMBER P730
The model number will be found on a plate attached to the motor housing.
Repair Sheet - Page 5
MODEL NUMBER P730
MAIN SWITCH
RED
FUSE
RED
CONTROL PCB BLACK
RED
CONTACT PLATE HOLDER
RED LOCK ON SWITCH
WHITE
BLACK RED
SHUT OFF PCB
GREEN
BLACK
MOTOR
BLUE ORANGE
RED BROWN
DIGITAL PRESSURE GAUGE
BLACK
WIRING DIAGRAM
* NOTE: The positive side of the motor has a red marking for identification.
RYOBI 18 VOLT INFLATOR -
Ryobi P730 Reviews
We have not received any reviews for Ryobi yet.