Owner's Manual
Page 3
Installation Manual Page - 3 - PWM-F110 Table of Contents Warning Statements ...- 4 Parts List ...- 6 Installation Tools ...- 6 Mounting Bracket Installation ...- 7 Wall Stud Location ...- 10 Installing the Flat Panel Display ...- 14 Technical Specifications ...- 16 Warranty ...- 17 Contact Premier Mounts ...- 17 Notes ...- 18 -
Installation Manual Page - 3 - PWM-F110 Table of Contents Warning Statements ...- 4 Parts List ...- 6 Installation Tools ...- 6 Mounting Bracket Installation ...- 7 Wall Stud Location ...- 10 Installing the Flat Panel Display ...- 14 Technical Specifications ...- 16 Warranty ...- 17 Contact Premier Mounts ...- 17 Notes ...- 18 -
Owner's Manual
Page 6
..." Flat Washers (Qty 4) GriPlates™ (Qty 8) Mounting Brackets (Qty 2) 5/16" x 3" Lag Bolts (wooden studs only) - (Qty 4) Wall Bumpers (Qty 2ea) M8 x 20mm Phillips Head Screws (Qty 6) M4 x 16mm Phillips Head Screws (Qty 8) Installation Tools Phillips Head Screw Driver Pencil Level (Supplied) Page - 6 - Soft Material/ Blanket Drill Gun Tape Measure 1/2" Socket and Wrench Installation Manual PWM-F110...
..." Flat Washers (Qty 4) GriPlates™ (Qty 8) Mounting Brackets (Qty 2) 5/16" x 3" Lag Bolts (wooden studs only) - (Qty 4) Wall Bumpers (Qty 2ea) M8 x 20mm Phillips Head Screws (Qty 6) M4 x 16mm Phillips Head Screws (Qty 8) Installation Tools Phillips Head Screw Driver Pencil Level (Supplied) Page - 6 - Soft Material/ Blanket Drill Gun Tape Measure 1/2" Socket and Wrench Installation Manual PWM-F110...
Owner's Manual
Page 10
... 8 1166"" Measure and mark the viewing height desired on Page 16) 2. PWM-F110 Wall Stud Location 1. Measure from the floor to the desired viewing height and mark the wall. Figure 9 Page - 10 - Once found, make a pencil marking on the center of your flat panel display once mounted on the wall (Figure 9). Wood Stud Finder (Commercially available) Mark the...
... 8 1166"" Measure and mark the viewing height desired on Page 16) 2. PWM-F110 Wall Stud Location 1. Measure from the floor to the desired viewing height and mark the wall. Figure 9 Page - 10 - Once found, make a pencil marking on the center of your flat panel display once mounted on the wall (Figure 9). Wood Stud Finder (Commercially available) Mark the...
Owner's Manual
Page 14
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. 1. Raise the flat panel with the mounting brackets secured to the flat panel and insert the top hooks from each bracket to the rod from the wall plates (Figure 14). Installation Manual PWM-F110 Installing the Flat Panel Display WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. Wall Plate Top Figure 14 Bottom Page - 14 -
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. 1. Raise the flat panel with the mounting brackets secured to the flat panel and insert the top hooks from each bracket to the rod from the wall plates (Figure 14). Installation Manual PWM-F110 Installing the Flat Panel Display WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. Wall Plate Top Figure 14 Bottom Page - 14 -
Owner's Manual
Page 15
CAUTION: Do not over tighten the ¼"-20 screws to adjust your flat panel. Use the wall bumper to the rods (Figure 15). NOTE: To remove the flat panel from the wall, simply back off the ¼"-20 screws using a Phillips screwdriver and lift the unit of the mounting brackets. PWM-F110 2. Wall Plate Wall Bumper Figure 15 Installation Manual Page - 15 - Make any lateral shift adjustments and lock it by tightening the two (2) ¼"-20 Phillips screws found on the bottom of the wall carefully.
CAUTION: Do not over tighten the ¼"-20 screws to adjust your flat panel. Use the wall bumper to the rods (Figure 15). NOTE: To remove the flat panel from the wall, simply back off the ¼"-20 screws using a Phillips screwdriver and lift the unit of the mounting brackets. PWM-F110 2. Wall Plate Wall Bumper Figure 15 Installation Manual Page - 15 - Make any lateral shift adjustments and lock it by tightening the two (2) ¼"-20 Phillips screws found on the bottom of the wall carefully.