Hardware Installation Guide
Page 7
...LEDs of the access point are described in the following figure and table: 12 345 6 Figure 1. ProSAFE Dual Band Wireless AC Access Point Model WAC740 Hardware Description The following sections describe the top and rear hardware functions of the access point. • Top Panel on page 7 • ...the access point is ready for about 30 seconds, turns solid green temporarily, then blinks amber while the configuration is being synchronized and the firmware is being updated, and finally turns solid green. Top panel LEDs Item Icon 1 LED Name LED Behavior Description Power LED Off Power ...
...LEDs of the access point are described in the following figure and table: 12 345 6 Figure 1. ProSAFE Dual Band Wireless AC Access Point Model WAC740 Hardware Description The following sections describe the top and rear hardware functions of the access point. • Top Panel on page 7 • ...the access point is ready for about 30 seconds, turns solid green temporarily, then blinks amber while the configuration is being synchronized and the firmware is being updated, and finally turns solid green. Top panel LEDs Item Icon 1 LED Name LED Behavior Description Power LED Off Power ...
Hardware Installation Guide
Page 8
...green WiFi activity is detected on LAN port 2 is carrying all traffic in a LAG connection. ProSAFE Dual Band Wireless AC Access Point Model WAC740 Table 1. Blinking green Network traffic is detected. 3 LAN LED 1 Off No Ethernet link or Ethernet LAG link is detected. If both ...group (LAG) connection. Top panel LEDs (continued) Item Icon LED Name LED Behavior Description 1 (continued) Blinking amber at fast speed Firmware is being synchronized. LED Solid green The 5 GHz WiFi radio is being upgraded. 2 Activity LED Off No link with the network is detected....
...green WiFi activity is detected on LAN port 2 is carrying all traffic in a LAG connection. ProSAFE Dual Band Wireless AC Access Point Model WAC740 Table 1. Blinking green Network traffic is detected. 3 LAN LED 1 Off No Ethernet link or Ethernet LAG link is detected. If both ...group (LAG) connection. Top panel LEDs (continued) Item Icon LED Name LED Behavior Description 1 (continued) Blinking amber at fast speed Firmware is being synchronized. LED Solid green The 5 GHz WiFi radio is being upgraded. 2 Activity LED Off No link with the network is detected....
Hardware Installation Guide
Page 29
..., the Power LED turns solid green. ProSAFE Dual Band Wireless AC Access Point Model WAC740 Verify the Correct Sequence of Events at Startup If the access point is managed by a firmware upgrade. • Firmware upgrade. LAN LED1. LAN LED 2 in a LAG. If any of events occurs... - LAN LED 1 in a LAG. The synchronization process might be followed by a wireless controller, after you suspect a system fault, contact NETGEAR technical support. Troubleshooting 29 The Power LED Remains Solid Amber or Remains Blinking Amber When the access point starts while it might blink green. ...
..., the Power LED turns solid green. ProSAFE Dual Band Wireless AC Access Point Model WAC740 Verify the Correct Sequence of Events at Startup If the access point is managed by a firmware upgrade. • Firmware upgrade. LAN LED1. LAN LED 2 in a LAG. If any of events occurs... - LAN LED 1 in a LAG. The synchronization process might be followed by a wireless controller, after you suspect a system fault, contact NETGEAR technical support. Troubleshooting 29 The Power LED Remains Solid Amber or Remains Blinking Amber When the access point starts while it might blink green. ...
Hardware Installation Guide
Page 30
...access point. Troubleshooting 30 If you are lit. Make sure that you suspect a system fault, contact NETGEAR technical support. If this behavior does not occur, or if the Activity LED is not lit, a.... Use a standard Category 5e or Category 6 Ethernet patch cable. Make sure that the configuration or firmware upgrade is complete, wait another five minutes, and then check to the network, the Activity LED is...LED stops blinking amber. ProSAFE Dual Band Wireless AC Access Point Model WAC740 If the Power LED does not stop blinking amber while the access point is controller managed, it...
...access point. Troubleshooting 30 If you are lit. Make sure that you suspect a system fault, contact NETGEAR technical support. If this behavior does not occur, or if the Activity LED is not lit, a.... Use a standard Category 5e or Category 6 Ethernet patch cable. Make sure that the configuration or firmware upgrade is complete, wait another five minutes, and then check to the network, the Activity LED is...LED stops blinking amber. ProSAFE Dual Band Wireless AC Access Point Model WAC740 If the Power LED does not stop blinking amber while the access point is controller managed, it...
Installation Guide
Page 1
... the 2.4 GHz WiFi radio. 5 GHz WLAN LED •Off. To compose the address, start with the network is being synchronized and the firmware is detected. •Blinking amber at moderate speed. The 2.4 GHz WiFi radio is detected. •Solid amber in a LAG. If your ...WiFi network that the DHCP server specifies the IP address of 192.168.0.160. Installation NETGEAR ProSAFE Dual Band Wireless AC Access Point WAC740 Package Contents Unpack the box and verify the contents: • WAC740 ProSAFE Dual Band Wireless AC Access Point • Category 5e Ethernet cable • ...
... the 2.4 GHz WiFi radio. 5 GHz WLAN LED •Off. To compose the address, start with the network is being synchronized and the firmware is detected. •Blinking amber at moderate speed. The 2.4 GHz WiFi radio is detected. •Solid amber in a LAG. If your ...WiFi network that the DHCP server specifies the IP address of 192.168.0.160. Installation NETGEAR ProSAFE Dual Band Wireless AC Access Point WAC740 Package Contents Unpack the box and verify the contents: • WAC740 ProSAFE Dual Band Wireless AC Access Point • Category 5e Ethernet cable • ...