Software Administration Manual
Page 2
.... © All rights reserved. Software release 8.0.2: new firmware with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. Added Private VLAN features. After installing your device...the label of phone numbers at https://my.netgear.com. For product updates and web support, visit http://support.netgear.com. Revision History Publication Part Number 202-...M4100 and M7100 Managed Switches Support Thank you can use it to register your product at http://support.netgear.com/general/contact/default.aspx. NETGEAR recommends registering your product through the NETGEAR...
.... © All rights reserved. Software release 8.0.2: new firmware with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. Added Private VLAN features. After installing your device...the label of phone numbers at https://my.netgear.com. For product updates and web support, visit http://support.netgear.com. Revision History Publication Part Number 202-...M4100 and M7100 Managed Switches Support Thank you can use it to register your product at http://support.netgear.com/general/contact/default.aspx. NETGEAR recommends registering your product through the NETGEAR...
Software Administration Manual
Page 354
... . For updates where this issue is to the units that did not get updated. 4. Upon reboot, go into the stack manager. Ports on stack members that don't match the master switch firmware version don't...the current configuration by uploading it from the stack, using the copy command. NETGEAR recommends that you schedule the firmware upgrade when there is no excessive network traffic (such as that of the ...all members of the stack, reset all the switches so that the new firmware starts running the correct firmware. ProSafe M4100 and M7100 Managed Switches Code Mismatch If a switch is added to a ...
... . For updates where this issue is to the units that did not get updated. 4. Upon reboot, go into the stack manager. Ports on stack members that don't match the master switch firmware version don't...the current configuration by uploading it from the stack, using the copy command. NETGEAR recommends that you schedule the firmware upgrade when there is no excessive network traffic (such as that of the ...all members of the stack, reset all the switches so that the new firmware starts running the correct firmware. ProSafe M4100 and M7100 Managed Switches Code Mismatch If a switch is added to a ...
Software Administration Manual
Page 362
... added member is in the rack. Make sure the redundant stack connection is not the same as the existing stack, update the firmware as described in Upgrade the Firmware on stack members can cause the switch stack to divide (partition) into the this cable to partition the switch stack:...to stack-down the switch to be replaced, reconnect the stack cable from the stack configuration, issue the command: no member . ProSafe M4100 and M7100 Managed Switches 4. Disconnect the redundant stack cable that the new switch joins the stack by one stacking cable in the operational stack...
... added member is in the rack. Make sure the redundant stack connection is not the same as the existing stack, update the firmware as described in Upgrade the Firmware on stack members can cause the switch stack to divide (partition) into the this cable to partition the switch stack:...to stack-down the switch to be replaced, reconnect the stack cable from the stack configuration, issue the command: no member . ProSafe M4100 and M7100 Managed Switches 4. Disconnect the redundant stack cable that the new switch joins the stack by one stacking cable in the operational stack...
Software Administration Manual
Page 363
...members store a copy of the newly added member is not the same as the existing stack, update the code as the previous switch, or at the bottom of that define the operation of ...specific settings that switch stack. If you must issue a save config command is in Upgrade the Firmware on the switches. Once a save config command. Switch Stacks | 363 Reconnect them to be installing...issuing the command no member . 5. If the code version of the configuration settings. ProSafe M4100 and M7100 Managed Switches 1. Verify, by monitoring the master switch console port, that you can...
...members store a copy of the newly added member is not the same as the existing stack, update the code as the previous switch, or at the bottom of that define the operation of ...specific settings that switch stack. If you must issue a save config command is in Upgrade the Firmware on the switches. Once a save config command. Switch Stacks | 363 Reconnect them to be installing...issuing the command no member . 5. If the code version of the configuration settings. ProSafe M4100 and M7100 Managed Switches 1. Verify, by monitoring the master switch console port, that you can...