Netgear FE516 - Hub - Stackable Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear FE516 manuals!
Problems with Netgear FE516?
Ask a Question
Free Netgear FE516 manuals!
Problems with Netgear FE516?
Ask a Question
Popular Netgear FE516 Manual Pages
Installation Guide - Page 6
... 10BASE-T network. By installing the Model FE508 or Model FE516 hub in the future.
This guide describes how to install and use the hub and includes physical configuration guidelines for individuals who have the following background and experience:
• Working knowledge of the NETGEAR™ Model FE508 8-port Fast Ethernet Hub or the Model FE516 16-port Fast Ethernet Hub. This guide is...
Installation Guide - Page 7
... individual port status. − Additional LEDs to a 100BASE-T switch or router. • Compact design enables tabletop or rack-mounting installation.
1-2
Introduction Installation Guide for the Model FE508 and FE516 Fast Ethernet Hubs
Features
The Model FE508 and Model FE516 hubs have the following key features: • IEEE 802.3u standard compliant for simplifying network extension...
Installation Guide - Page 8
... chassis consists of the hub is 1.0 EIA rack-mount spaces high. Front panel of the Model FE516 hub.
1 = LEDs (Power, Data, and Collision) 2 = RJ-45 ports with a steel cover and an acrylic front panel overlay. Figure 2-1 shows the front panel of the Model FE508 hub and Figure 2-2 shows the front panel of the Model FE508 Fast Ethernet hub
Physical Description
2-1
Installation Guide - Page 10
... networks require only 2-pair).
Refer to Appendix C, "Fast Ethernet and Cabling Guidelines," for the Normal (MDI-X) RJ-45 connector and the Uplink (MDI) RJ-45 connector.
Table B-1 provides the pin out information for more information on cabling.
CAUTION: 100 Mbps operation requires the use of the Model FE508 hub provides 8 RJ-45 100BASE-TX ports and the Model FE516...
Installation Guide - Page 11
... pressed in the out position. The remaining (Normal) ports on the hubs cannot be configured for Uplink wiring. When the push button is connected to select Uplink (MDI-X) or Normal (MDI) wiring for Port 8 on the Model FE508 hub and Port 16 on the Model FE516 hub.
Installation Guide for the Model FE508 and FE516 Fast Ethernet Hubs
Normal/Uplink Push Button
The Normal/Uplink push button...
Installation Guide - Page 13
...," for a maximum of 64 (100 Mbps) ports in a single repeater or collision domain. Figure 2-5. Refer to each hub.
Installation Guide for the Model FE508 and FE516 Fast Ethernet Hubs
Cascade Connectors
The Model FE508 and Model FE516 Fast Ethernet hubs can consist of any combination of Model FE508 and Model FE516 hubs daisy-chained together using a NETGEARsupplied cascade cable.
Installation Guide - Page 18
...EIA/TIA 568-A standard recommends the installation of Category 5 UTP to handle up to the
point of the hub. For instructions on a table or shelf, follow when installing 100 Mb/s networks. Figure 3-1. Installation Guide for the Model FE508 and FE516 Fast Ethernet Hubs
Installing a NETGEAR 100BASE-T Hub
This section provides information and instructions for proper wire placement according to...
Installation Guide - Page 19
... any combination of Model FE508 and Model FE516 hubs (maximum of four hubs to the RJ-45 connectors. When installation for the Model FE508 and FE516 Fast Ethernet Hubs
2. Installation
3-5 Attach the hub (with the mounting bracket) to the rack using Category 5 UTP wiring and connectors to a stack). Set the hub on installing multiple hubs, see "Installing Multiple Hubs" later in the...
Installation Guide - Page 24
... rear panel is off. Installation Guide for the Model FE508 and FE516 Fast Ethernet Hubs
Verifying Your Installation
When installation is complete and power has been applied to Chapter 4, "Troubleshooting."
3-10
Installation The Terminator LED
on the middle hub(s) is on. • In a stack of hubs, the Terminator LEDs on the top and bottom hubs are any port in the hub and
the Data LED...
Installation Guide - Page 27
... sure the Normal/Uplink push button is in the Uplink position. Excessive collisions can result when multiple hubs are cascaded and when many computers are other causes for the Model FE508 and FE516 Fast Ethernet Hubs
Table 4-1. Troubleshooting (continued)
Symptom Collision LED blinking
LEDs Collision on
Problems with Port 8 on the Model FE508 hub or with Port 16 on the front panel.
Installation Guide - Page 29
... interconnection devices in various configurations. The Model FE508 and Model FE516 hubs can be used in a standalone network with 10 Mbps repeaters, switching hubs, or other networking devices. The hub can be stacked in any combination for the Model FE508 and FE516 Fast Ethernet Hubs
Configuration Examples
The Model FE508 and Model FE516 hubs are used with users attached directly to...
Installation Guide - Page 30
... adding a NETGEAR Model SW502 Ethernet Switch that affect network performance is congestion. In many users are connected and accessing one server on a 10 Mbps link, congestion and collisions occur more common problems that has one 10 Mbps port and one 100 Mbps port, the existing 10 Mbps users can access the server through the 100 Mbps port on the switch. This configuration provides...
Installation Guide - Page 31
Migrating to form a mixed speed network. Figure 5-2. Installation Guide for the Model FE508 and FE516 Fast Ethernet Hubs
Figure 5-2 illustrates 100 Mbps users connected to a Model FE516 hub accessing a common server, integrated with the NETGEAR Model SW502 Ethernet Switch and a Model EN516 Ethernet Hub to 100 Mbps operation
5-4
Network Configuration Examples
Installation Guide - Page 35
... Model FE516 Fast Ethernet hubs. Figure B-1 illustrates the RJ-45 connector used to Port 8 on the Model FE508 hub and Port 16 on hubs. Table B-1 provides the pin out information for the Normal (MDI-X) RJ-45 connector and the pin out information for the Uplink (MDI) port (Port 8 on the Model FE508 and Port 16 on the RJ-45 connectors that are used for port connections on the Model FE516 hub...
Installation Guide - Page 42
...2-1 configuration examples, 5-2
migration to 100 Mbps, 5-3 multiport switch, 5-5 shared repeater, 5-2
connectors cascade, 2-6 Cascade Down, 3-7 Cascade Up, 3-7 RJ-45, 2-3, 1, 5
contents, package, 3-2 customer support, iii
-E- hub stacking, 2-6 humidity requirements, 3-1
-I-
installation guidelines, 3-3 in a rack, 3-4 of multiple hubs, 3-7 on a flat surface, 3-3 verifying, 3-9
Index-1
Ethernet...
Netgear FE516 Reviews
We have not received any reviews for Netgear yet.