AXM752 Installation Guide
Page 1
... operational. Installing a AXM752 Module Insert the module firmly into the module slot. The module can be inserted or removed while the switch is single mode LC to the automatic detection capability of the switch, installation of the module slot. Removing a AXM752 Module Release the module latch by pulling down the handle bar across the module, and pull the module out of AXM752 only requires that supports the XFP interface. Specifications Standard...
... operational. Installing a AXM752 Module Insert the module firmly into the module slot. The module can be inserted or removed while the switch is single mode LC to the automatic detection capability of the switch, installation of the module slot. Removing a AXM752 Module Release the module latch by pulling down the handle bar across the module, and pull the module out of AXM752 only requires that supports the XFP interface. Specifications Standard...
AXM752 Installation Guide
Page 2
...hereby certified the NETGEAR model AXM752 has being tested and found to comply with limits for a Class B digital device, pursuant to part 15 of ...instructions. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to change without notice. Note: This device has being suppressed in accordance with the condition set... herein. NETGEAR is Class 1 laser product Warning - Information is connected, avoid exposure to test the series for example, test transmitters) in a commercial installation. Federal Office...
...hereby certified the NETGEAR model AXM752 has being tested and found to comply with limits for a Class B digital device, pursuant to part 15 of ...instructions. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to change without notice. Note: This device has being suppressed in accordance with the condition set... herein. NETGEAR is Class 1 laser product Warning - Information is connected, avoid exposure to test the series for example, test transmitters) in a commercial installation. Federal Office...
AXM752 Product Datasheet
Page 2
10GBASE-LR XFP Optical Transceiver AXM752 Pb FEATURES Full duplex transmission at 9.95 to 11.08 Gbps 1310nm Electro Absorption Modulated Laser (EML) light source Standard LC duplex fiber-optic connector Compliant with IEEE 802.3ae Draft 5.0 Compliant with XFP MSA Rev. 4.0 I2C for integrated Digital Optical Monitoring Power consumption
10GBASE-LR XFP Optical Transceiver AXM752 Pb FEATURES Full duplex transmission at 9.95 to 11.08 Gbps 1310nm Electro Absorption Modulated Laser (EML) light source Standard LC duplex fiber-optic connector Compliant with IEEE 802.3ae Draft 5.0 Compliant with XFP MSA Rev. 4.0 I2C for integrated Digital Optical Monitoring Power consumption
AXM752 Product Datasheet
Page 3
... Differential RX Data Output RD+ - Input voltage swing (differential) measured peak-to -peak AXM752 Max Units Notes 85 °C 90 % 6.0 V 3.6 V Max 70 85 3.465 5.25 500 250 2.5 1000 800 Units °C % V V mA mA W mVp-p mVp-p Notes [1] [2,3] [4] ASIC / SerDes XFP XFP ASIC / SerDes 10Gbps XFI electrical signal 10Gbps optical signal Application Block Diagram 10Gbps...
... Differential RX Data Output RD+ - Input voltage swing (differential) measured peak-to -peak AXM752 Max Units Notes 85 °C 90 % 6.0 V 3.6 V Max 70 85 3.465 5.25 500 250 2.5 1000 800 Units °C % V V mA mA W mVp-p mVp-p Notes [1] [2,3] [4] ASIC / SerDes XFP XFP ASIC / SerDes 10Gbps XFI electrical signal 10Gbps optical signal Application Block Diagram 10Gbps...
AXM752 Product Datasheet
Page 4
Optical Transmitter Characteristics (TC=0 ºC to 70 ºC) Parameter Symbol Min Signaling speed (nominal) Ts Signaling speed variation from nominal Center Wavelength λ Side Mode Suppression Ratio SMSR Optical Modulaion Amplitude OMA Extinction Ratio ER Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3} 1260 30 10.3125 ±... Notes Transmitter eye mask definition 4. Typ 10.3125 Max ±100 1355 0.5 -12.6 -18 Units Gb/s ppm nm dBm dBm dBm dBm Notes [1] 3 Revision: 0A AXM752 3.
Optical Transmitter Characteristics (TC=0 ºC to 70 ºC) Parameter Symbol Min Signaling speed (nominal) Ts Signaling speed variation from nominal Center Wavelength λ Side Mode Suppression Ratio SMSR Optical Modulaion Amplitude OMA Extinction Ratio ER Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3} 1260 30 10.3125 ±... Notes Transmitter eye mask definition 4. Typ 10.3125 Max ±100 1355 0.5 -12.6 -18 Units Gb/s ppm nm dBm dBm dBm dBm Notes [1] 3 Revision: 0A AXM752 3.
AXM752 Product Datasheet
Page 5
AXM752 5. C' Symbol Min Typ Max Units Notes Deterministic Jitter Total Jitter Eye Mask DJ TJ X1 X2 Y1 170 Y2 0.18 UI (p-p) [1] 0.34 UI (p-p) [1] 0.17 UI 0.42 UI mV 425 mV Notes: 1. Includes jitter transferred from the optical receiver during any valid operational input condition. XFI Module Receiver Differential Output Compliance Mask XFI Termination and AC Coupling 4 Revision: 0A XFI Module Receiver Output Jitter Specifications at C' Parameter -
AXM752 5. C' Symbol Min Typ Max Units Notes Deterministic Jitter Total Jitter Eye Mask DJ TJ X1 X2 Y1 170 Y2 0.18 UI (p-p) [1] 0.34 UI (p-p) [1] 0.17 UI 0.42 UI mV 425 mV Notes: 1. Includes jitter transferred from the optical receiver during any valid operational input condition. XFI Module Receiver Differential Output Compliance Mask XFI Termination and AC Coupling 4 Revision: 0A XFI Module Receiver Output Jitter Specifications at C' Parameter -
AXM752 Product Datasheet
Page 6
6. Pin Description XFP Host Board Connector Pad Layout (Top View) AXM752 Recommended Host Board Supply Filtering Network 5 Revision: 0A
6. Pin Description XFP Host Board Connector Pad Layout (Top View) AXM752 Recommended Host Board Supply Filtering Network 5 Revision: 0A
AXM752 Product Datasheet
Page 7
...14 LVTTL-O RX_LOS Receiver Loss Of Signal Indicator [1] 15 GND Module Ground 16 GND Module Ground 17 CML-O RD- Grounded in the low power mode. 22 VCC2 +1.8V Power Supply --Not Required 23 GND Module Ground 24 PECL-I P_Down/RST consumption to a voltage between 3.15V...serial interface Interrupt Bar; When high, requires the module to 3 LVTTL-I TD+ Transmitter Non-Inverted Data Input 30 GND Module Ground Notes: 1. When held low allows module to respond to limit power 21 LVTTL-I RefCLK- AXM752 Module Electrical Pin Function Definition Pin Logic Symbol Name/...
...14 LVTTL-O RX_LOS Receiver Loss Of Signal Indicator [1] 15 GND Module Ground 16 GND Module Ground 17 CML-O RD- Grounded in the low power mode. 22 VCC2 +1.8V Power Supply --Not Required 23 GND Module Ground 24 PECL-I P_Down/RST consumption to a voltage between 3.15V...serial interface Interrupt Bar; When high, requires the module to 3 LVTTL-I TD+ Transmitter Non-Inverted Data Input 30 GND Module Ground Notes: 1. When held low allows module to respond to limit power 21 LVTTL-I RefCLK- AXM752 Module Electrical Pin Function Definition Pin Logic Symbol Name/...
AXM752 Product Datasheet
Page 8
...board. 4 TX_DIS TX_DIS is "High", the module shall not respond to VCC3 in the module. The RX_LOS pin is asserted High, the XFP module transmitter output must be turned off. Mod_DeSel pin must be pulled to Host_Vcc on a single 2-wire interface bus. When TX_DIS is an ...XFP module. 5 MOD_ABS Mod_ABS is an input pin. Mod_ABS is then asserted "High" when the XFP module is an output pin. The assertion and de-assertion periods of the Mod_DeSel deassert time before communicating with the newly selected module. When held Low by the host, the module responds to the host system. AXM752...
...board. 4 TX_DIS TX_DIS is "High", the module shall not respond to VCC3 in the module. The RX_LOS pin is asserted High, the XFP module transmitter output must be turned off. Mod_DeSel pin must be pulled to Host_Vcc on a single 2-wire interface bus. When TX_DIS is an ...XFP module. 5 MOD_ABS Mod_ABS is an input pin. Mod_ABS is then asserted "High" when the XFP module is an output pin. The assertion and de-assertion periods of the Mod_DeSel deassert time before communicating with the newly selected module. When held Low by the host, the module responds to the host system. AXM752...
AXM752 Product Datasheet
Page 9
The P_Down/RST pin must be pulled up to VCC3 in the XFP module. 7.1 POWER DOWN FUNCTION The P_Down pin, when held High by the host, places the module in the standby (Low Power) mode with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board. 8 Revision: 0A Shall be pulled up with a maximum power dissipation of 1.5W. 7.2 RESET FUNCTION The negative edge of P_Down/RST signal initiates a complete module reset.Notes: 3. AXM752 7 P_DOWN/RST This is a multifunction pin for module Power Down and Reset.
The P_Down/RST pin must be pulled up to VCC3 in the XFP module. 7.1 POWER DOWN FUNCTION The P_Down pin, when held High by the host, places the module in the standby (Low Power) mode with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board. 8 Revision: 0A Shall be pulled up with a maximum power dissipation of 1.5W. 7.2 RESET FUNCTION The negative edge of P_Down/RST signal initiates a complete module reset.Notes: 3. AXM752 7 P_DOWN/RST This is a multifunction pin for module Power Down and Reset.
AXM752 Product Datasheet
Page 10
Memory Map of Management Interface AXM752 The lower memory table (Byte 0~127) is listed as following table. 9 Revision: 0A Besides, it has been allocated three upper memory tables for digital diagnostics and control functions. The detail memory content is for serial ID, user writable and vendor specific functions. 8.
Memory Map of Management Interface AXM752 The lower memory table (Byte 0~127) is listed as following table. 9 Revision: 0A Besides, it has been allocated three upper memory tables for digital diagnostics and control functions. The detail memory content is for serial ID, user writable and vendor specific functions. 8.
AXM752 Product Datasheet
Page 11
... 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 AXM752 Hex ASCII DC DC DC DC DC DC 08 60 67 Note 4 VS Note 5 VS VS VS VS VS VS VS VS VS VS VS... VS VS VS VS VS VS VS VS VS VS VS Notes: 1) CC_BASE : Check code for Base ID Fields (address 120~190) 2) Vendor SN (address 196-211) 3) Date Code (address 212-219) 4) CC_EXT : Check code for Extended ID Fields (address 192~222) 5) Address 224~255 is reserved for vendor specific EEPROM 10 Revision: 0A
... 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 AXM752 Hex ASCII DC DC DC DC DC DC 08 60 67 Note 4 VS Note 5 VS VS VS VS VS VS VS VS VS VS VS... VS VS VS VS VS VS VS VS VS VS VS Notes: 1) CC_BASE : Check code for Base ID Fields (address 120~190) 2) Vendor SN (address 196-211) 3) Date Code (address 212-219) 4) CC_EXT : Check code for Extended ID Fields (address 192~222) 5) Address 224~255 is reserved for vendor specific EEPROM 10 Revision: 0A
AXM752 Product Datasheet
Page 12
... current of transmitter at room temperature Value (Dec.) 90 -10 85 -5 Iop+60 mA Iop-25 mA Iop+55 mA Iop-20 mA P+3 P-3 P+2 P-2 -3 -23 -5 -21 5.5 4.5 5.3 4.7 3.6 3.0 3.5 3.1 AXM752 Unit ℃ mA dBm dBm Volt Volt 11 Revision: 0A
... current of transmitter at room temperature Value (Dec.) 90 -10 85 -5 Iop+60 mA Iop-25 mA Iop+55 mA Iop-20 mA P+3 P-3 P+2 P-2 -3 -23 -5 -21 5.5 4.5 5.3 4.7 3.6 3.0 3.5 3.1 AXM752 Unit ℃ mA dBm dBm Volt Volt 11 Revision: 0A
AXM752 Product Datasheet
Page 13
AXM752 General State/ Control Bits Byte 1 1 1 1 110 110 110 110 110 110 110 110 111 111 111 111 111 119-122 123-126 127 Bit Name 0 ... All Password Entry All Table Select Description Default value of this bit is 0 XFI loopback enable when this bit set to 1 Not Implement Default setting is 10.3Gbps Digital state of the Tx disable input pin Read/ Write bit that allow software disable of laser Digital state of Module Not Ready Digital state Power...
AXM752 General State/ Control Bits Byte 1 1 1 1 110 110 110 110 110 110 110 110 111 111 111 111 111 119-122 123-126 127 Bit Name 0 ... All Password Entry All Table Select Description Default value of this bit is 0 XFI loopback enable when this bit set to 1 Not Implement Default setting is 10.3Gbps Digital state of the Tx disable input pin Read/ Write bit that allow software disable of laser Digital state of Module Not Ready Digital state Power...
AXM752 Product Datasheet
Page 14
AXM752 83 7 Rx Power High Warning Set when received power exceeds high warning level 83 6 Rx Power Low Warning Set when received power is below low warning level 83 5 AUX1 High Warning Set when internal 5V supply voltage exceeds high warning level 83 4 AUX1 Low Warning Set when internal 5V supply voltage is below low warning level 83 3 AUX2 High Warning Set when internal 3.3V supply voltage exceeds high warning level 83 2 AUX2 Low Warning Set when internal 3.3V supply voltage is below low warning level 83 1 Reserved 83 0 Reserved 13 Revision: 0A
AXM752 83 7 Rx Power High Warning Set when received power exceeds high warning level 83 6 Rx Power Low Warning Set when received power is below low warning level 83 5 AUX1 High Warning Set when internal 5V supply voltage exceeds high warning level 83 4 AUX1 Low Warning Set when internal 5V supply voltage is below low warning level 83 3 AUX2 High Warning Set when internal 3.3V supply voltage exceeds high warning level 83 2 AUX2 Low Warning Set when internal 3.3V supply voltage is below low warning level 83 1 Reserved 83 0 Reserved 13 Revision: 0A
AXM752 Product Datasheet
Page 15
Mechanical Outline Dimensions Transmitter Wavelength / Application Latch Color Identifier 1310nm / LR Blue AXM752 272-10320-02 AXM752 Single Mode/1310nm 10Gbps 10GBase-LR up to 10km Complies with 21 CFR 1040.10 and 1040.11 Class 1 Laser Product R Made in Taiwan 14 Revision: 0A 11.
Mechanical Outline Dimensions Transmitter Wavelength / Application Latch Color Identifier 1310nm / LR Blue AXM752 272-10320-02 AXM752 Single Mode/1310nm 10Gbps 10GBase-LR up to 10km Complies with 21 CFR 1040.10 and 1040.11 Class 1 Laser Product R Made in Taiwan 14 Revision: 0A 11.
AXM752 Product Datasheet
Page 16
AXM752 11. Regulatory Compliance Feature Reference Electromagnetic Interference FCC CRF 47, Part15 Class B (EMI) EN 55022 Class B (CISPR 22A) Radio Frequency Electromagnetic Field Electrostatic Discharge to ... the Electrical Pins EN 61000-4-3 IEC 61000-4-3 EN 61000-4-2 IEC 61000-4-2 IEC 801.2 MIL-STD-883E Method 3015.7 Performance (1) Satisfied with electrical characteristics of product spec. (2) No physical damage Eye Safety US FDA CDRH AEL Class 1 Component Recognition Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information UL File...
AXM752 11. Regulatory Compliance Feature Reference Electromagnetic Interference FCC CRF 47, Part15 Class B (EMI) EN 55022 Class B (CISPR 22A) Radio Frequency Electromagnetic Field Electrostatic Discharge to ... the Electrical Pins EN 61000-4-3 IEC 61000-4-3 EN 61000-4-2 IEC 61000-4-2 IEC 801.2 MIL-STD-883E Method 3015.7 Performance (1) Satisfied with electrical characteristics of product spec. (2) No physical damage Eye Safety US FDA CDRH AEL Class 1 Component Recognition Underwriters Laboratories and Canadian Standards Association Joint Component Recognition for Information UL File...
AXM752 Product Datasheet
Page 17
S0 S1 S2 0A Date 2006-04-25 2006-08-25 2007-10-02 2007-11-09 Description Preliminary datasheet for RoHS version Update Digital Diagnostic Memory Map contents Modify the dimension of label Modify the Byte 165~167 of A0h AXM752 16 Revision: 0A Document Revision Version No. Appendix A.
S0 S1 S2 0A Date 2006-04-25 2006-08-25 2007-10-02 2007-11-09 Description Preliminary datasheet for RoHS version Update Digital Diagnostic Memory Map contents Modify the dimension of label Modify the Byte 165~167 of A0h AXM752 16 Revision: 0A Document Revision Version No. Appendix A.
AXM752 Product Datasheet
Page 18
Information is subject to change without notice. All rights reserved. Other brand names mentioned herein are trademarks of their respective holder(s). D-AXM752-0 NETGEAR, the NETGEAR Logo, NETGEAR Digital Entertainer Logo, Connect with Innovation, FrontView, IntelliFi, PowerShift, ProSafe, RAIDar, RAIDiator, X-RAID, RangeMax, ReadyNAS and Smart Wizard are for identification purposes only and may be trademarks of NETGEAR, Inc. in the United States and/or other countries. © 2008 NETGEAR, Inc.
Information is subject to change without notice. All rights reserved. Other brand names mentioned herein are trademarks of their respective holder(s). D-AXM752-0 NETGEAR, the NETGEAR Logo, NETGEAR Digital Entertainer Logo, Connect with Innovation, FrontView, IntelliFi, PowerShift, ProSafe, RAIDar, RAIDiator, X-RAID, RangeMax, ReadyNAS and Smart Wizard are for identification purposes only and may be trademarks of NETGEAR, Inc. in the United States and/or other countries. © 2008 NETGEAR, Inc.