NEC V864Q-AVT2 Support and Manuals
Get Help and Manuals for this NEC item
This item is in your list!
View All Support Options Below
Free NEC V864Q-AVT2 manuals!
Problems with NEC V864Q-AVT2?
Ask a Question
Free NEC V864Q-AVT2 manuals!
Problems with NEC V864Q-AVT2?
Ask a Question
Popular NEC V864Q-AVT2 Manual Pages
External Controls - Page 10
...
Refer to section 5.1 "Get current parameter from a monitor." Usually, this message when you want to get , specify the "OP code page" and "OP code", refer to "Appendix A.
"Message format" of the "Set parameter" is allied to the "Message Type" in the "Get parameter message". Message format of the "Get current parameter" is...
External Controls - Page 22
... to control the monitor, these are examples of Message
Check code BCC: Block Check Code Refer to get a value. Typical procedure example
The following is 10h (in the OP code page 0). ETX (03h): End of "Get
parameter", "Set parameter" and "Save current settings".
6.1. How to support this operation. (Get parameter)
Header SOH-'0'-Monitor ID-
'0'-'C'-'0'-'6'
Message STX...
External Controls - Page 23
... (02h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is 10h (in the page 0). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h): Set Backlight setting 80(0050h). No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is the controller. Delimiter
(23/145)
Delimiter CR (0Dh): End of packet
Step 4. Delimiter CR (0Dh): End of packet...
External Controls - Page 25
... (30h, 30h, 30h, 31h): temperature sensor is #1. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is 78h (in the page 2). '0'-'0' (30h, 30h): This... "Set parameter" type. '0'-'0'-'0'-'3' (30h, 30h, 30h, 33h): Number of Message
Check code BCC: Block Check Code Refer to 'A', the replying Monitor ID is '1'. 'F' (46h): Message Type is "Set parameter...
External Controls - Page 26
... replying Monitor ID is '1'. 'D' (44h): Message Type is "Get parameter reply". '1'-'2' (31h, 32h): Message length is set to send the temperature from the selected sensor.
No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 25 degrees Celsius. Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller...
External Controls - Page 52
...setting.
Delimiter CR (0Dh): End of Message
(52/145) Monitor ID: Indicate a replying Monitor ID. 7.2 Power control
1) The controller requests the monitor to the section 4.3 "Check code" for confirmation. No error...command '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Power mode 0001: ON 0002, 0003: Do not set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". ...
External Controls - Page 55
...confirmation.
Ex.) When this byte is set to the section 4.3 "Check code" for a BCC calculation.
(55/145) Delimiter CR (0Dh): End of Message
Check code BCC: Block Check Code Refer to 'A', the replying Monitor ID...top of Asset data. 00h : Write data from top of the Asset data area. No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data write command '0'-'0'(30h, 30h): Offset ...
External Controls - Page 125
...): Start of Message 'C'-'B'-'0'-'9' (43h, 42h, 30h, 39h): Setting Copy Reply '0'-'2' (30h, 30h): Start ST: Status
No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of Message
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation.
Ex.) When this byte is set to 'A', replying monitor's ID is '1'. 'B' (42h): Message...
Users Manual - English - Page 3
...Problems...this manual. ...instructions, may cause undesired operation. If necessary, the user should contact the dealer or an experienced radio/television technician for a Class B digital device, pursuant to part... U.S.
NEC is no...installation.
However, there is a registered trademark of Product:
Display Monitor
Equipment Classification: Class B Peripheral
Model:
V754Q V864Q...
Users Manual - English - Page 7
... wall configuration for a long time, slight expansion of the monitor by improper installation. The monitor must be mounted. Please contact your supplier, as hook, eyebolt or mounting parts and then secure the monitor with the installation instructions. Maintenance
• Periodically check for support. The device may cause the monitor to become distorted or damaged.
•...
Users Manual - English - Page 9
...)
V654Q/V754Q
V864Q
Attaching Mounting Accessories...NEC logo ornament position
When using only the eyebolts. Removing the logo ornament: unscrew the installed screw then take off the logo ornament.
Screw holes
400 mm
Mounting accessories can be attached with the VESA mounting system.
1. Eyebolts are required when transporting. English-7 English
Changing handles position
: Factory set...
Users Manual - English - Page 21
...that supports 2A.
• Please refer to the specifications page for the USB setting.
...In this port.
• Please make sure the connector shape and orientation is correctly aligned when connecting the USB device or cable.
• Depending on the use this case, please check user's manual... (Type-B). USB CM2:
Service port. To use the Media...
Users Manual - English - Page 27
... FOLDER
Check the check box to the file list screen.
Selects a setting for when the slideshow finishes.
Selects AUTO or MANUAL. If OK is not pressed, settings that contains images or movies.
• A slideshow can be displayed using "MANUAL" in which the images are switched by operating a button on the screen. English...
Users Manual - English - Page 47
...settings under COMPUTE MODULE.
SYSTEM
MONITOR INFORMATION
Shows the model name, serial number and firmware version of IR remote control signals.
Please do not change settings in kg-CO2. SERVICE MENU
SETTING...sets the maximum amount of GPIO 23 to signal that is turned off. CHANGE PASSWORD... specifications. When set until the power to the Compute Module is installed to...
Users Manual - English - Page 60
... select AUTO TURN OFF then press SET/POINT ZOOM. buttons select YES then press SET/POINT ZOOM button on . Connected HDMI CEC supporting devices obtains the monitor's power status...
Please refer to the user's manual supplied with "Change Language function". If the monitor is necessary that connecting this function copes with the HDMI CEC supported device for HDMI CEC devices connection...
NEC V864Q-AVT2 Reviews
Do you have an experience with the NEC V864Q-AVT2 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!