NEC C861Q-AVT2 Support and Manuals
Get Help and Manuals for this NEC item
This item is in your list!
View All Support Options Below
Free NEC C861Q-AVT2 manuals!
Problems with NEC C861Q-AVT2?
Ask a Question
Free NEC C861Q-AVT2 manuals!
Problems with NEC C861Q-AVT2?
Ask a Question
NEC C861Q-AVT2 Videos
Popular NEC C861Q-AVT2 Manual Pages
External Controls - Page 10
... "Message format" of the "Get parameter reply" is as follows,
STX Result OP code OP code
Type
Max value
Requested setting
ETX
page
Value
Hi Lo Hi Lo Hi Lo Hi Lo MSB
LSB
MSB
LSB
...current parameter
The controller sends this message for a confirmation of the "Set parameter reply" is as follows,
STX
Result
OP code
OP code
Type
Max value
Current Value
ETX
page
Hi Lo Hi Lo Hi ...
External Controls - Page 22
... get a value. The monitor replies with the current brightness setting and
capability to the section 4.3 "Check code" for a BCC calculation. Message STX (02h): Start of Message
Check code BCC: Block Check Code Refer to support this operation. (Get parameter)
Header SOH-'0'-Monitor ID-
'0'-'C'-'0'-'6'
Message STX-'0'-'0'-'1'-'0'-ETX
Check code BCC
Delimiter CR
Header SOH (01h): Start of...
External Controls - Page 23
...Message '0'-'0' (30h, 30h): Result code. Monitor ID: Indicate a replying Monitor ID. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is the controller.
BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Message STX (02h): Start of which you want to change a setting. Header
Message
SOH-'0'-'0'- Monitor ID...
External Controls - Page 25
... 'A', the replying Monitor ID is '1'. 'F' (46h): Message Type is "Set parameter reply". '1'-'2' (31h, 32h): Message length is the controller. The monitor replies for confirmation.
Message STX (02h): Start of Message
(25/145)
No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is 78h (on page 2). '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Select...
External Controls - Page 26
No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is set to send the temperature from the selected sensor. Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'C' (43h): Message Type is "Get ...
External Controls - Page 52
...ETX
Check code BCC
Delimiter CR
Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is 32bytes. No error. 'C'-'2','0'-'3'-'D'-'6' (...control
1) The controller requests the monitor to change a setting.
Message STX (02h): Start of Message
Check code BCC: Block Check Code Refer to the controller. '0'-'0'-'0'-'1' (30h, 30h, ...
External Controls - Page 55
... (03h): End of Message
Check code
BCC: Block Check Code Refer to the monitor at a time is 32bytes. Ex.) When this byte is set to the section 4.3 "Check code" for a BCC calculation. Data...length Note.) The maximum data length that can be written to the section 4.3 "Check code" for confirmation. No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data write command '0'-'0'(30h, 30h):...
External Controls - Page 125
... (01h): Start of Message
Check code
BCC: Block Check Code Refer to 'A', replying monitor's ID is '1'. 'B' (42h): Message type is "Command reply". '0'-'A'(30h,41h): Message length (10byte)
Message
STX (02h): Start of Message 'C'-'B'-'0'-'9' (43h, 42h, 30h, 39h): Setting Copy Reply '0'-'2' (30h, 30h): Start ST: Status
No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX...
Users Manual - English - Page 3
... cable with the instructions, may cause harmful...operate this manual.
Failure ...installation.
For HDMI, DisplayPort and D-Sub 9-pin, please use a shielded signal cable with Part 15 of Product:
Display Monitor
Equipment Classification: Class B Peripheral
Model:
C751Q C881Q C981Q
SUPPLIER'S DECLARATION OF CONFORMITY
This device complies with ferrite core. Responsible Party: NEC...
Users Manual - English - Page 7
...you use a trained, NEC authorized service person. This device cannot be used in a video wall configuration for loose screws, gaps, distortions, or other problems that may occur with ...inspect the installation location to ensure that it is strongly recommended to follow NEC standard mounting procedures could result in Specification (see "C651Q" on page 72, "C751Q" on page 73, "C861Q" on page...
Users Manual - English - Page 9
... N•cm)
C651Q/C751Q
C861Q
Attaching Mounting Accessories
The monitor...This model is equipped with attachable eyebolts to installation, ... can easily support the weight of the monitor. Install the logo ...NEC logo ornament position can be changed. NOTE:
Prior to aid in mounting. • Install...English
Changing handles position
: Factory set position. : Alternate position.
Attaching...
Users Manual - English - Page 21
...manual of your computer or device, or contact your supplier for the USB setting...supports 2A.
• Please refer to a USB compatible computer with a USB cable. Do not disconnect the USB cable or disconnect and reconnect the USB cable before the monitor recognizes the input.
• You can control the devices connected to the specifications... port. USB CM2:
Service port. Connect to the...
Users Manual - English - Page 27
... the file display screen.
• When still images in which the images are switched automatically at a set interval (PLAY MODE is "AUTO").
• The default factory setting is kept on the configuration screen. Selects AUTO or MANUAL. Selects a setting for when the slideshow finishes. BLACK SCREEN: When the slideshow finishes, a black screen...
Users Manual - English - Page 47
....
FACTORY RESET
All items are installed, additional OSD menu items will automatically be available for when the display should start receiving WDT reset commands.
SERVICE MENU
SETTING LOCK
Locks all daisy chained monitors.
POWER
POWER SUPPLY
Controls power to the slot 2 type option specifications. Please be shutting down. When set until the power to factory...
Users Manual - English - Page 60
... . Please refer to the user's manual supplied with an HDMI cable.
For the "Change Language function", it changes the input from an input, which is in standby mode or on the CEC. buttons select YES then press SET/POINT ZOOM button on the ON. Connected HDMI CEC supporting devices obtains the monitor's power...
NEC C861Q-AVT2 Reviews
Do you have an experience with the NEC C861Q-AVT2 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!