NEC C981Q-AVT2 Support and Manuals
Get Help and Manuals for this NEC item
This item is in your list!
View All Support Options Below
Free NEC C981Q-AVT2 manuals!
Problems with NEC C981Q-AVT2?
Ask a Question
Free NEC C981Q-AVT2 manuals!
Problems with NEC C981Q-AVT2?
Ask a Question
NEC C981Q-AVT2 Videos
Popular NEC C981Q-AVT2 Manual Pages
External Controls - Page 10
...". "Message format" of the "Get parameter reply" is used for more details.
4) Set Parameter reply
The monitor replies with the status of the "Set parameter message". Message format of the "Set parameter" is as follows,
STX
Result
OP code
OP code
Type
Max value
Current Value
ETX
page
Hi Lo Hi Lo Hi Lo Hi...
External Controls - Page 22
... Monitor ID. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the OP code page 0). Typical procedure example
The following is 50(0032h) .
Control Commands 6. The controller requests the Monitor to reply with current Backlight setting and capability to support this byte is set to the section 4.3 "Check code" for a BCC...
External Controls - Page 23
...is 10h (in the page 0). '0'-'0' (30h, 30h): This operation is "Set parameter" type. '0'-'0'-'6'-'4' (30h, 30h, 36h, 34h): Backlight max value is 100(0064h). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h): Received a Backlight setting was 80(0050h) . No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the page 0). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h...
External Controls - Page 25
...Check code BCC
Delimiter CR
Header SOH (01h): Start of Message
(25/145) No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code ...controller. 'E' (45h): Message Type is "Set parameter command". '0'-'A' (30h, 41h): Message length is 18 bytes. Message STX (02h): Start of Message
Check code BCC: Block Check Code Refer to get a value. 6.2. Target displays...
External Controls - Page 26
...code BCC
Header SOH (01h): Start of selected sensor. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2). Check code BCC: Block Check Code... (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2). '0'-'0' (30h, 30h): This operation is "Set parameter" type. 'F'-'F'-'F'-'F' (46h...
External Controls - Page 52
... Check Code Refer to change a setting. Message STX (02h): Start of packet
2) The monitor replies a data for a BCC calculation. Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'C (30h, 43h): Message length is the controller. Ex.) The byte data 20h is 32bytes.
No error. 'C'-'2','0'-'3'-'D'-'6' (43h...
External Controls - Page 55
...a replying Monitor ID. Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (... maximum data length that can be written to write Asset data. No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data write command '0'-'0'(... Write data into from top of Message
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation.
(55/145) ETX...
External Controls - Page 125
... (10byte)
Message
STX (02h): Start of Message 'C'-'B'-'0'-'9' (43h, 42h, 30h, 39h): Setting Copy Reply '0'-'2' (30h, 30h): Start ST: Status
No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of Message
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of Header '0' (30h): Reserved...
Users Manual - English - Page 3
...instructions...Part 15 of SD-3C, LLC. in a particular installation. Failure to Identify and Resolve Radio-TV Interference Problems."...Model:
C751Q C881Q C981Q
SUPPLIER'S DECLARATION OF CONFORMITY
This device complies with Part 15 of America, Inc.
Responsible Party: NEC...part 15 of NEC Corporation.
All other cables and adapters may not cause harmful interference, and (2) this manual...
Users Manual - English - Page 7
... mounting accessory for loose screws, gaps, distortions, or other problems that comply with the installation instructions. For NEC Qualified Personnel:
Stability Hazard. To prevent injury, this monitor is mentioned in the box.
The safety wire must not be able to the printed contents sheet provided in Specification (see "C651Q" on page 72, "C751Q" on page...
Users Manual - English - Page 9
...mounting. • Install the eyebolt brackets with the screws, which are required when transporting. C981Q
2. Attach Mounting Accessories
Be careful to install the logo ornament. Install the logo ornament ...set position. : Alternate position. To avoid scratching the LCD panel, always place a soft cloth, such as shown in the portrait position, the NEC logo ornament position can easily support...
Users Manual - English - Page 21
...(2A) port for power supply, please use a USB cable that supports 2A.
• Please refer to the specifications page for the USB setting. Do not disconnect the USB cable or disconnect and reconnect the USB...USB device or cable.
• Depending on the use this case, please check user's manual of your computer or device, or contact your supplier for detailed information.
• Before ...
Users Manual - English - Page 27
....
• When still images in high resolutions are switched by operating a button on the configuration screen.
To perform "AUTO", set the "PLAY MODE" to "AUTO".
• The images will be displayed using "MANUAL" in which the images are displayed as the Slideshow, it goes back to display the configuration screen of the...
Users Manual - English - Page 47
... all daisy chained monitors.
CHANGE PASSWORD
Default values can reset all items in SLOT2 CH SELECT.
2CH
The DisplayPort signal is installed to factory shipment state. FACTORY RESET
All items are installed, additional OSD menu items will automatically be careful to the slot 2 type option specifications.
English
SLOT2 CH SETTING
Selects signal type according to...
Users Manual - English - Page 60
... to the same language, which you selected. Please refer to the user's manual supplied with the HDMI CEC supported device for the selected device. The function sends digital audio signal through the HDMI cable.
buttons select ON then press SET/POINT ZOOM button on the YES. By using buttons select AUDIO RECIEVER then...
NEC C981Q-AVT2 Reviews
Do you have an experience with the NEC C981Q-AVT2 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!