NEC UN492VS Support and Manuals
Get Help and Manuals for this NEC item
Popular NEC UN492VS Manual Pages
External Controls - Page 10
... message when you want to get , specify the "OP code page" and "OP code", refer to "Appendix A. Operation code table". Message format of the "Set parameter" is as follows,
STX OP code OP code
Set Value
ETX
page
Hi Lo Hi Lo MSB
LSB
Refer to section 5.3 "Set parameter" for more details.
5) Command "Command message" format depends...
External Controls - Page 22
... controller requests the Monitor to reply with current Backlight setting and capability to support this byte is 6 bytes. Delimiter CR (0Dh): End of Message '0'-'0' (30h, 30h): Result code. Message STX (02h): Start of packet
Step 2. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 18 bytes. ETX (03h): End of Message...
External Controls - Page 23
... BCC
Delimiter CR
Header SOH (01h): Start of Message '0'-'0' (30h, 30h): Result code.
No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the page 0). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h): Set Backlight setting 80(0050h). Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'E' (45h): Message Type...
External Controls - Page 25
..., 30h, 30h, 31h): temperature sensor is the controller. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is 78h (in temperature sensors.
Message STX (02h): Start of Message '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is "Set parameter" type. '0'-'0'-'0'-'3' (30h, 30h, 30h, 33h): Number of Message...
External Controls - Page 26
...parameter reply". '1'-'2' (31h, 32h): Message length is set to the section 4.3 "Check code" for a BCC calculation. ETX (03h): End of ...error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2). Delimiter CR
(26/145)
Monitor ID: Indicate a replying Monitor ID. Check code BCC: Block Check Code Refer to the section 4.3 "Check code...
External Controls - Page 52
... control command '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Power mode 0001: ON 0002, 0003: Do not set. 0004: OFF (same as the power off by IR) ETX (03h): End of Header '0' (30h...Message length Note.) The maximum data length that can be written to the section 4.3 "Check code" for confirmation. No error. 'C'-'2','0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply command ...
External Controls - Page 55
...ETX
Check code BCC
Delimiter CR
Header SOH (01h): Start of Message
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation.
(55/145) No error. 'C'-'0'-'0'-'E'...0Dh): End of Message '0'-'0': Result code.
Message STX (02h): Start of packet
2) The monitor replies a data for a BCC calculation. Ex.) When this byte is set to 'A', the replying Monitor ID ...
External Controls - Page 125
...30h): Message receiver is the controller.
Delimiter CR (0Dh): End of Message
Check code BCC: Block Check Code Refer to the section 4.3 "Check code" for a BCC calculation. Ex.) If Monitor ID is '1', specify 'A'. '0'... Start of Message 'C'-'B'-'0'-'9' (43h, 42h, 30h, 39h): Setting Copy Reply '0'-'2' (30h, 30h): Start ST: Status
No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of...
User Manual English - Page 31
...Supports HDCP (High-bandwidth Digital Contents Protection) coding, a type of digital rights management that prevents highdefinition content, in the [TERMINAL SETTINGS...set [DisplayPort1.2]
and [MST] at each connected monitors with the DisplayPort OUT connector, please set [OVERSCAN] to [AUTO] or [OFF] as display drivers...correctly due to different HDMI specifications. English−27 See page...
User Manual English - Page 43
...: View the monitor information (model, serial number, carbon footprint), firmware version, mac address, or perform a factory reset. See page 104.
MULTI-INPUT: Select Picture-In-Picture and Picture-By-Picture settings, signal input detection, and connection terminal settings. MULTI-DISPLAY: Set the monitor's monitor ID, configure settings for multi-monitor setup. A table listing all options...
User Manual English - Page 83
... enter the CEC options.
The device's name and the HDMI connection it is set to select [AUDIO RECEIVER] then press SET/POINT ZOOM.
buttons to highlight [ON], then press SET/POINT ZOOM button to the user's manual supplied with HDMI CEC supporting devices.
While this function obtains the device's name.
Please refer to enable CEC...
User Manual English - Page 93
... master monitor can also be entered here. For example, if you want to the NEC website for Android devices. Function name Setting Copy Setting read and write function Display information Security Setting
English−89
The MEMO text must be installed on the left column below HOME. Shows a list of monitor IDs and IP addresses...
User Manual English - Page 114
...reduced image may have
cropped edges.
H POS
Horizontal position.
This setting may require different scanning modes in the monitor.
Part of the outside of the active screen area are not shown..... When starting tile matrix in multi-display installations, if the [ASPECT] is [DYNAMIC] or [ZOOM] it is installed in order to its previous setting. When the SCREEN SAVER stops, the ASPECT...
User Manual English - Page 128
... monitor.
Selects the mode [UNLOCK], [ALL LOCK] or [CUSTOM LOCK]. Select [LOCK] to prevent volume adjustment. English−124 No password is locked. button when the IR Remote is required to lock all settings are available for normal operation. Select [LOCK] to lock the button. Select [LOCK] to power on this function.
Video Wall Installation Guide - Page 1
... distributed across the video wall by using the Tile Matrix function. Guide
NEC Display Solutions
Video Wall Installation Guide
Settings and Adjustments for MultiSync® UN552S | UN552VS | UN552 | UN552V | UN492S | UN492VS | UN462A | UN462VA
A guide to trouble-free, efficient video wall installation
This guide will assist you in setting up to UHD/30 resolution via DisplayPort, HDMI or OPS can...
NEC UN492VS Reviews
We have not received any reviews for NEC yet.