Makita BSS611Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita BSS611Z manuals!
Problems with Makita BSS611Z?
Ask a Question
Free Makita BSS611Z manuals!
Problems with Makita BSS611Z?
Ask a Question
Makita BSS611Z Videos
Makita BSS611Z Cordless 6 1/2 Inch Circular Saw Review - Full HD - OnlineToolReviews
Duration: 19:17
Total Views: 80
Duration: 19:17
Total Views: 80
Makita Bare-Tool BSS611Z 18-Volt LXT Lithium-Ion Cordless 6-1/2-Inch Circular Saw
Duration: :46
Total Views: 2,745
Duration: :46
Total Views: 2,745
Popular Makita BSS611Z Manual Pages
Owners Manual - Page 2
... of the warnings listed below may result in electric shock, fire and/or serious injury. Personal Safety 9. Failure to a rotating part of flammable liquids, gases or dust. A moment of electric shock. Do not use reduces the risk of inattention while operating power tools may ignite the dust or fumes. 3. ENGLISH
SPECIFICATIONS
Model
BSS610
BSS611
Blade diameter
165...
Owners Manual - Page 3
... with sharp cutting edges are less likely to another battery pack. 25. in accordance with these instructions and in use ) replace strict adherence to minimize body exposure, blade binding, or loss of control.
3 Inserting the battery pack into account the working conditions and the work properly to circular saw , they cannot be ejected from oil and grease...
Owners Manual - Page 4
...When ripping always use damaged or incorrect blade washers or bolt. Never use a rip fence or straight edge guide. If saw backward while the blade is binding, or when interrupting a cut...saw will also make exposed metal parts of the power tool "live " wire will run eccentrically, causing loss of blade pinching and kickback. Supports must be controlled by the kerf closing down, the blade...
Owners Manual - Page 5
... cut . Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback. Do not use gasoline. Always observe that the lower guard is accidentally dropped, lower guard may cut , be retracted manually only for proper closing before each use . Gum and wood pitch hardened on blades slows saw down on the section...
Owners Manual - Page 6
... burns and even an explosion. 4. Never attempt to follow the safety rules stated in
this manual. Wear a dust mask and hearing protection
FOR BATTERY CARTRIDGE
1. Do not short the battery cartridge: (1) Do not touch the terminals with the circular saw blade.
20. A battery short can lead to prevent dust inhalation and skin contact. Do not store the tool and...
Owners Manual - Page 7
... lever on the side of the cartridge.
• To insert the battery cartridge, align the tongue on the front base. If you .
006702
0-45
0-50
1. Set for maintaining maximum battery life 1. Turn the stopper counterclockwise fully for bevel cut 1. Overcharging shortens the battery service life. 3. Adjusting depth of the button, it clockwise for dangerous KICKBACKS...
Owners Manual - Page 8
... lamp For Model BSS610 only
CAUTION: • Do not look in the light or see that the tool is switched off lever. Shaft lock 2. Return tool a MAKITA service center for the desired angle (0° - 50°) by tilting accordingly, then tighten the lever securely. The blade brake system is installed with an electric blade brake. ASSEMBLY...
Owners Manual - Page 9
... be cut by the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use , store the hex wrench as shown in the figure. Saw blade 3. Install the dust nozzle on the upper side of the tool, causing injury to you or someone around you can see the red part on the tool...
Owners Manual - Page 10
...Guide
rule)
90
45
1
1. MAINTENANCE
CAUTION: • Always be replaced at the factory.
For Model BSS610 After replacing brushes, insert the battery cartridge into the tool and break in the holders. Release switch, wait for blade to chips and wood dust being ejected from saw...clean cuts, keep your sawing line straight and
your local Makita service center for repair.
10 Then check the...
Owners Manual - Page 11
... defective workmanship or material, Makita will repair (or at our option, replace) without charge. Brush holder
1
cap
2. Only use with your local Makita Service Center. • Carbide-tipped saw blades
Combination 006540
General purpose blade for fast and smooth rip, crosscuts and miters.
• Rip fence (Guide rule) • Hex wrench 5 • Dust nozzle • Various type of...
Parts Breakdown - Page 2
...Model BSS611Z
Parts List
A = Standard Equipment
〇= Circuit Diagram
Fig. Part No.
1
265995-6
2
450227-6
3
651976-0
4
231469-9
5
419664-3
7
231469-9
9
643812-4
10
419665-1
11
265995-6
12
419281-9
13
643829-7
14
194435-6
15
911263-2
16
643825-5
17
643824-7
18...'Y 18V INC. 23,25,26 FAN 55 BALL BEARING 6000LLB SHAFT LOCK COMPRESSION SPRING 5 BLADE CASE COMPLETE...
Parts Breakdown - Page 3
.... SOCKET HEAD SCREW M5X6 BASE COMPLETE HEX. 48 49 50 51 56 57 58 59 60 61 62 65 66 67 68 69 70 71 72 73 76 77 78 79 81 82 85...) S-34 INNER FLANGE 35 OUTER FLANGE 35 HEX. LOCK NUT M5-8 ANGULAR GUIDE + PAN HEAD SCREW M5 FLAT HEAD SCREW M6X90 SHOULDER PIN 6-7 SHOULDER PIN 6-7 HEX. SOCKET SET SCREW M5X8 FLAT WASHER 7 GUIDE RULE HEX. WRENCH 5 T.C.T.SAW BLADE 165X24TX15.88
1 PC. 1 PC. 1 PC. 1 PC. 1 PC....
Makita BSS611Z Reviews
We have not received any reviews for Makita yet.