Makita XNJ01 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XNJ01 manuals!
Problems with Makita XNJ01?
Ask a Question
Free Makita XNJ01 manuals!
Problems with Makita XNJ01?
Ask a Question
Popular Makita XNJ01 Manual Pages
Makita DC18RC Instruction Manual - Page 3
...damaged, ask Makita authorized
service center to replace it within five seconds after this battery charger. 5. tery, and (3) product using battery charger, read all instructions and cautionary markings... battery cartridge is BELOW 10°C (50°F) or ABOVE 40°C (104°F). ENGLISH
Specifications
Model Input Output Weight
DC18RA
DC18RC
A.C. 120 V 50 - 60 HZ
D.C. 7.2 V - 18 V
...
Makita DC18RC Instruction Manual - Page 4
...• Yellow light will begin after the cooling fan installed in red color, battery condition is as , being ...trouble on the charger or battery cartridge are clogged with cooling fan for the batteries in order to enable the battery to repair... charging selected according to direct sunlight for charging Makita-battery cartridge. Recharge of cells
14.4 V 4
18 V 5
14.4 ...
XNJ01Z Instruction Manual - Page 2
....
7.
Cluttered or
dark areas invite accidents. 2. Electrical Safety 4.
ENGLISH (Original instructions)
SPECIFICATIONS
Model
XNJ01
Mild steel
1.6 mm / 16 ga
Max. cutting radius
Outside edge Inside edge
50... / BL1840
• Due to follow the warnings and instructions may differ from heat, oil, sharp edges or moving parts. Work area safety 1. Keep work area clean and well...
XNJ01Z Instruction Manual - Page 3
... from those intended could burn your power tool serviced by poorly maintained power tools. 22. SAVE THESE INSTRUCTIONS.
3 Keep cutting tools sharp and clean.
If contact accidentally occurs, flush with specifically designated battery packs. Keep handles dry, clean and free from moving parts. 4. GEB028-2
NIBBLER SAFETY WARNINGS
1. Wear gloves. they may create...
XNJ01Z Instruction Manual - Page 4
... service life. 3.
Let a hot battery cartridge cool down before
completely discharged. Do not use ) replace ...strict adherence
to safety rules for a long period of your eyes, rinse them out with clear water and seek medical attention right away.
If electrolyte gets into your eyesight. 5. Be careful not to follow the safety rules stated in this
instruction manual...
XNJ01Z Instruction Manual - Page 5
...stops: 1. Red indicator
2
3. The tool will automatically stop the application that causes it is overheated. Installing or removing battery cartridge
1. Battery cartridge
3
013284
CAUTION: • Always switch off power to the...of the button, it , proceed as desired. 3. If you . • Do not install the battery cartridge forcibly. If not, it may cause them to slip off and stop ...
XNJ01Z Instruction Manual - Page 6
...set. Align the notch to the cutting line on tool.
Die holder 2. Remove the die holder from the die holder.
Indicating lamp
1
013277
Indication lamps are located in two positions. − Battery cartridge replacing... the punch. Die
2
3. Gauge for allowable cutting thickness. Removing or installing the punch and die
1
1. Do not attempt to the cutting width....
XNJ01Z Instruction Manual - Page 7
...Then install the die holder on the die holder. Die
1
4
3. From the side view 5. Corrugated or trapezoidal sheet metal
013280
Set the...7 Tighten the lock nut to increase the
punch and die service life. Die holder
013286
Cutouts can be inserted into the... the tool for a while.
1. After replacing the punch and die, lubricate them with machine oil to secure the die holder. Punch...
XNJ01Z Instruction Manual - Page 8
...Always be replaced at a right angle (90°) to slip in the tool
package as shown in this manual. Take... the limit mark. Replace when they wear down to country.
3
013281
8 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance ...Makita Authorized or Factory Service Centers, always using Makita replacement parts. Screwdriver
Use a screwdriver to persons.
XNJ01Z Instruction Manual - Page 9
... state to the tool. This Warranty does not apply where:
repairs have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY.
XNJ01Z Parts Breakdown - Page 2
...XNJ01 NAME PLATE TAPPING SCREW 4X18 SWITCH KNOB HOUSING SET RUBBER PIN 6 INC. 36 SWITCH LEVER SWITCH 1246.3223 CONTROLLER TERMINAL HOUSING SET...PC. 0 1 PC. 1 PC. 1 1 PC. 1 2 PC. 0 1 SET 2 PC. 2 PC. 1 PC. 1 PC. 1 2 PC. Model XNJ01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
001
266048-4
002
141878-3
002 C10 800P78-7
003
331438-1
004
212222-2
005...
Makita XNJ01 Reviews
We have not received any reviews for Makita yet.