Linksys WET11 - Instant Wireless EN Bridge Network Converter Support and Manuals
Get Help and Manuals for this Linksys item
View All Support Options Below
Free Linksys WET11 manuals!
Problems with Linksys WET11?
Ask a Question
Free Linksys WET11 manuals!
Problems with Linksys WET11?
Ask a Question
Most Recent Linksys WET11 Questions
Linksys Wet11 Setup Software
Where can I download the Linksys WET11 setup software ?Thanks, Jim
Where can I download the Linksys WET11 setup software ?Thanks, Jim
(Posted by jimtwest3 5 years ago)
Popular Linksys WET11 Manual Pages
User Guide - Page 3
...-B Ethernet Bridge Web-based Utility
14
Overview
14
Starting the Web-based Utility
14
Setup
15
Password
17
Advanced
18
Status
19
Help
20
Appendix A: Troubleshooting
21
Common Problems and Solutions
21
Frequently Asked Questions
22
Appendix B: Wireless Security
25
A Brief Overview
25
What Are the Risks?
25
Appendix C: Upgrading Firmware
32
Appendix D: Windows Help...
User Guide - Page 7
....
• Chapter 7: Using the Wireless-B Ethernet Bridge Web-based Utility This chapter explains how to use the Web-Based Utility to configure the settings on the Bridge.
• Appendix A: Troubleshooting This appendix describes some problems and solutions, as well as frequently asked questions, regarding installation and use of the Wireless-B Ethernet Bridge.
• Appendix B: Wireless...
User Guide - Page 14
The Setup Utility should run automatically, and the screen in Figure 5-1 should appear. Click the LINKSYS Web button to exit the Setup Wizard.
2. Make sure the Bridge is the letter of this User Guide.
• LINKSYS Web - The Setup Wizard will guide you through all the necessary steps. Insert the Setup CD-ROM into your wired network, you are ready to set it...
User Guide - Page 15
...IP address... installing ...Utility). Click the Infrastructure radio button if you are using a wireless access point. Click the Next button to continue or the Back button to return to network directly with the status information for the Bridge. The screen shown in Figure 5-5 shows a choice of Bridges Figure 5-4: Password
Chapter 5: Setting Up the Wireless-B Ethernet Bridge Setup Wizard...
User Guide - Page 16
...must be unique to function correctly.
8. Enter an IP Address, IP Mask, and Gateway appropriate to the previous screen. The Security Settings screen, shown in your network. This IP address must specify an IP address on the Bridge, click the radio button next to Set IP configuration manually to match your network's channel setting (available for your network has a router or DHCP...
User Guide - Page 17
... Wireless-B Ethernet Bridge Web-based Utility." Write down the Bridge's IP Address if you did not enter a Passphrase, then enter a WEP key in the Key 1 field. To register the Bridge, click the Online Registration button. The Wireless-B Ethernet Bridge is now successfully configured for Network Use." Go to configure advanced settings through the Bridge's Web-based...
User Guide - Page 19
... perform more advanced configuration changes, use the Utility. Lets you to online technical support resources. This chapter explains how to use your web browser, and enter the IP address of various configuration settings and links to configure the IP address and wireless settings.
• Password -
Enables you change these settings or make more advanced configuration or monitoring...
User Guide - Page 20
... Configuration-DHCP. The SSID must not exceed 32 alphanumeric characters, which may assign any spaces). Choose a wireless operating mode for all devices in a wireless network. Chapter 7: Using the Wireless-B Ethernet Bridge Web-based Utility Setup
Figure 7-2: Setup Tab 15 Firmware updates are assigning the Bridge a static IP address, then select Static IP Address, and enter an IP...
User Guide - Page 24
...Web-based Utility Status
Figure 7-7: Status Tab 19 LAN Settings
• IP Address - The status of packets transmitted to the Bridge is displayed here. • Wireless RX -
LAN Statistics
• Ethernet TX - Firmware should be
upgraded ONLY if you have assigned to the wireless network is displayed here. • Firmware Version - Firmware updates are posted at www.linksys.com...
User Guide - Page 26
... Bridges are set to enable MAC address cloning on again, or push the Reset button. Perform the following steps: • Verify that may occur during the installation and operation of the access point.
2. Click the Advanced tab. 3. Click the Auto radio button. 5. I don't know how to problems that the operating mode is set to different IP addresses. •...
User Guide - Page 27
... Bridge to access, and its IP address will depend on the same IP network.
5. Select the Bridge you are identical for wireless networks. This will appear in your web browser. After I run the Setup Wizard.
Frequently Asked Questions
What is designed to be reset to the default setting; This will reset the password to the factory defaults as the...
User Guide - Page 37
... Downloads for the firmware version. 6. Appendix C: Upgrading Firmware
32 Firmware should be upgraded ONLY if you experience problems with the firmware utility on -screen instructions. Version 2, and then select your computer. 8. Click the word here in Click here to http://linksys.com/download. 2. Read the release notes for this Product button. 4. The WET11 Firmware Upgrade utility...
User Guide - Page 41
...you the name associated with an e-mail address. HTTP (HyperText Transport Protocol) -
Half Duplex - Currently installed computing and networking equipment.
IP (Internet Protocol) - IP Address - An IEEE standard network protocol that protect the resources of computers, telecommunications, and other information technology devices. Firmware - 1. Breaking a packet into read-only...
User Guide - Page 44
... A network protocol for greater security. Upgrade - URL (Uniform Resource Locator) -...no directory or password capability. The address of the TCP/IP FTP protocol that...IP (Transmission Control Protocol/Internet Protocol) - A network protocol for transmitting data that displays the IP address for accessing remote PCs. WEP (Wired Equivalent Privacy) - To replace existing software or firmware...
Quick Start Guide - Page 1
... WET11's cable to another device that the PWR and the LAN indicator lights on the router. There are now in the || position, NOT the |X| position.
3. One you to do it directly to configure the device any degree of our current listings for a username and password. You can get here. Though the manual and Linksys tech support...
Linksys WET11 Reviews
We have not received any reviews for Linksys yet.