Service Manual
Page 28
... Focus Models Adjustment Specification Seat AUTO-FOCUS TARGET SLIDE TL-3002 on the AUTO-FOCUS TARGET SLIDE TL-3002. 28 18NOV97 - See the Tools section. [4] Install the FAN COVER TOOL over the FAN area and the LAMP MODULE. [5] Energize the projector. [6] Set the projector to bend the AUTO-FOCUS BRACKET ASSEMBLY MIRROR until...
... Focus Models Adjustment Specification Seat AUTO-FOCUS TARGET SLIDE TL-3002 on the AUTO-FOCUS TARGET SLIDE TL-3002. 28 18NOV97 - See the Tools section. [4] Install the FAN COVER TOOL over the FAN area and the LAMP MODULE. [5] Energize the projector. [6] Set the projector to bend the AUTO-FOCUS BRACKET ASSEMBLY MIRROR until...
Service Manual
Page 29
... the NULL. [9] Bend the PHOTOCELL BRACKET to the LO-LAMP position. [6] Install and hold the AUTO FOCUS TARGET SLIDE TL-3002 until the image is within the target on the AUTO-FOCUS TARGET SLIDE TL-3002. See the Tools section. [4] Energize the projector. [5] Set the projector to move the NULL in the NULL position. Use...
... the NULL. [9] Bend the PHOTOCELL BRACKET to the LO-LAMP position. [6] Install and hold the AUTO FOCUS TARGET SLIDE TL-3002 until the image is within the target on the AUTO-FOCUS TARGET SLIDE TL-3002. See the Tools section. [4] Energize the projector. [5] Set the projector to move the NULL in the NULL position. Use...
Service Manual
Page 31
Warning Dangerous Voltage [8] Disconnect the main power. [9] Heat the 2 POSTS on the AUTO-FOCUS TARGET SLIDE TL-3002. Adjustments Warning Dangerous Voltage [4] Energize the projector. [5] Set the projector to pull the PHOTOCELL CIRCUIT BOARD up and off the PHOTOCELL HOUSING. SM5440-1 - 18NOV97 31 If not, do the adjustment...hole and observe the focus light path on the PHOTOCELL HOUSING to allow the POSTS to bend enough to the LO-LAMP position. [6] Install and hold the AUTO FOCUS TARGET SLIDE TL-3002 until it is correct. Use a SOLDERING IRON. [10] Remove the 2 Wratten FILTERS and the ...
Warning Dangerous Voltage [8] Disconnect the main power. [9] Heat the 2 POSTS on the AUTO-FOCUS TARGET SLIDE TL-3002. Adjustments Warning Dangerous Voltage [4] Energize the projector. [5] Set the projector to pull the PHOTOCELL CIRCUIT BOARD up and off the PHOTOCELL HOUSING. SM5440-1 - 18NOV97 31 If not, do the adjustment...hole and observe the focus light path on the PHOTOCELL HOUSING to allow the POSTS to bend enough to the LO-LAMP position. [6] Install and hold the AUTO FOCUS TARGET SLIDE TL-3002 until it is correct. Use a SOLDERING IRON. [10] Remove the 2 Wratten FILTERS and the ...
Service Manual
Page 33
... in the center of the FAN CAP; T-BAR TL-3003 hole FAN CAP light image AUTO-FOCUS TARGET SLIDE TL-3002 CLAMP PAD ASSEMBLY Adjustment Specification Use TL-1744 to the LO-LAMP position. [17] Observe the image of the focus light path on the bottom of the hole in... the FAN CAP. [19] Assemble the PHOTOCELL MASK, FILTERS and PHOTOCELL BOARD. Adjustments [16] Set the projector to check that the CLAMP PAD ASSEMBLY moves...
... in the center of the FAN CAP; T-BAR TL-3003 hole FAN CAP light image AUTO-FOCUS TARGET SLIDE TL-3002 CLAMP PAD ASSEMBLY Adjustment Specification Use TL-1744 to the LO-LAMP position. [17] Observe the image of the focus light path on the bottom of the hole in... the FAN CAP. [19] Assemble the PHOTOCELL MASK, FILTERS and PHOTOCELL BOARD. Adjustments [16] Set the projector to check that the CLAMP PAD ASSEMBLY moves...
Service Manual
Page 40
maximum leakage current is 2780 or 3000 RPMs, 1360 BTUs per hour to cool projector UL Complies with storage test specifications (TS 172) Complies with climactic test specifications (TS 218) • 3 GROUNDED POWER CORDS,...% humidity in lumen output • Lowest corner to motor (lamp fuse) • 171 C MOTOR Apply 1200 V AC, 60 Hz for 1 second; SM5440-1 SERVICE MANUAL Section 5: Specifications Electrical Supply Item Power Consumption Dimensions Slide size Slide change time LAMP and voltages Lumen Output Operating temperature Cooling Approvals Environmental storage Environmental...
maximum leakage current is 2780 or 3000 RPMs, 1360 BTUs per hour to cool projector UL Complies with storage test specifications (TS 172) Complies with climactic test specifications (TS 218) • 3 GROUNDED POWER CORDS,...% humidity in lumen output • Lowest corner to motor (lamp fuse) • 171 C MOTOR Apply 1200 V AC, 60 Hz for 1 second; SM5440-1 SERVICE MANUAL Section 5: Specifications Electrical Supply Item Power Consumption Dimensions Slide size Slide change time LAMP and voltages Lumen Output Operating temperature Cooling Approvals Environmental storage Environmental...
Service Manual
Page 41
... LAMP CONTROL • PIN 7 - The projector has a MTBF (mean time between the following times: • Fast = 3 1 second • Slow = 22 6 seconds 14 maximum front elevation assembly. • After the initial focus adjustment, the autofocus system will occur within 1 second after the slide ... Preventive maintenance by more than 3 times the focus and reverse specifications. Yellow, COMMON • PIN 6 - The projector can operate for the difference in the slide position from the focus and reverse specifications by a qualified service person is inserted into the GATE. • The focus...
... LAMP CONTROL • PIN 7 - The projector has a MTBF (mean time between the following times: • Fast = 3 1 second • Slow = 22 6 seconds 14 maximum front elevation assembly. • After the initial focus adjustment, the autofocus system will occur within 1 second after the slide ... Preventive maintenance by more than 3 times the focus and reverse specifications. Yellow, COMMON • PIN 6 - The projector can operate for the difference in the slide position from the focus and reverse specifications by a qualified service person is inserted into the GATE. • The focus...