KitchenAid KUID508HBL Support and Manuals
Get Help and Manuals for this KitchenAid item
View All Support Options Below
Free KitchenAid KUID508HBL manuals!
Problems with KitchenAid KUID508HBL?
Ask a Question
Free KitchenAid KUID508HBL manuals!
Problems with KitchenAid KUID508HBL?
Ask a Question
KitchenAid KUID508HBL Videos
KitchenAid KUID508HBL Ice Maker
Duration: :37
Total Views: 14
Duration: :37
Total Views: 14
KitchenAid KUID508HBL Machines à glaçon
Duration: :36
Total Views: 1
Duration: :36
Total Views: 1
Popular KitchenAid KUID508HBL Manual Pages
Owners Manual - Page 1
...instructions. Do not use an extension cord. Disconnect power before servicing.
In Canada, register your ice maker at www.kitchenaid.ca. This is , tell you how to move and install... includes a condensed User Guide.
Always read and obey all parts and panels before operating.
A complete Use and Care Guide can be downloaded at www.kitchenaid.com/manuals. Do not remove ground...
Owners Manual - Page 5
... turned on .
Replace the fuse or reset the circuit breaker. If there was a large amount of water through the inlet valve. For models with the flow ...Part Number W10355010
In U.S.A., order Part Number W10355016
In Canada, order Part Number W10355010B
In Canada, order Part Number W10355016B
TROUBLESHOOTING
Visit producthelp.kitchenaid.com for the drain pump to follow these instructions...
Owners Manual - Page 6
...and form clumps.
NOTE: Service technicians cannot repair plumbing problems outside of installation. Check that all parts and panels before servicing. If there is securely in the ice bin.
Ice Quality
PROBLEM
Off Taste, Odor or ...provided.
Thin, Soft or Clumps of time.
Replace all packaging materials were removed at the time of the ice maker. If the drain...
Owners Manual - Page 7
...Part Number ICE2. Application Guidelines/Water Supply Parameters
Water Supply
City or Well
Water Pressure
30 - 120 psi (207 - 827 kPa)
Water Temperature
33°- 100°F (0.6° - 37.8°C)
Service Flow Rate 0.
50 gpm (1.89 Lpm) @ 60 psi
®NSF is essential that you replace...DATA SHEET
Ice Maker Water Filtration System
Model P6GEG2KL, P6KG2KL, P6WG2KL Capacity 2000 ...
Owners Manual - Page 8
...with electrical or plumbing codes, or correction of repair or replacement under this major appliance is used in the country in -home repair. 12. Discoloration, rust, or oxidation of surfaces resulting from the date of product replacement, your appliance will be addressed without service. This product is installed, operated, and maintained according to the instructions attached to correct...
Installation Instructions - Page 1
... your appliance. We have provided many important safety messages in this manual and on some models 5 Drain Connection 8 Door Reversal-Side Swing Only 9 Leveling 11 Cleaning 11
SÉCURITÉ DE LA MACHINE À GLAÇONS 13 INSTRUCTIONS D'INSTALLATION.......... 14
Déballage de la machine à glaçons........ 14 Exigences d'emplacement 14...
Installation Instructions - Page 2
...installing the ice maker under a counter, follow basic precautions, including the following:
Children should allow the ice maker to be pulled forward for servicing if necessary.
■ Installation... use chlorine bleach on some models) is not damaged or pinched...instruction concerning use of the appliance by a person responsible for their safety.
Do not use replacement parts...
Installation Instructions - Page 5
...Part Number 1901A.
■ Do not connect the outlet end of ice maker) (5)
■ 5/8" small adjustable hose clamp (secures vent to drain pump)
■ 7/8" large adjustable hose clamp, (secures drain tube to ice maker bin and drain pump reservoir inlet) (3)
■ Rear panel (2)
■ Instruction sheet
If Ice Maker Is Currently Installed...some models)
.... Replace all state and local codes and...
Installation Instructions - Page 9
Replace all parts and panels before servicing. Failure to the door.
8. Remove the handle screws and handle (on the bottom of your model...replace the top hinge pin.
5. NOTE: Be sure the edge guards do so can result in the package with the Use and Care Guide...
Tools Needed Gather the required tools and parts before starting installation.
■ 5/16" wrench
■...Set the door aside.
9
Installation Instructions - Page 10
... opposite side of the door and set aside.
2.
Top Hinge
Bottom Hinge A
B
C D
E
A. Remove the screws from the opposite side of the ice maker and tighten screws.
3. Replace the screws in the empty hinge...the magnetic door catch and place them on some models)
1. Phillips-head countersink screw C. Align the door with the top hinge hole and replace the top
hinge pin. 3. Turn the hinge ...
Installation Instructions - Page 11
... for the ice maker to raise that are on some models, remove the screw from the cutter grid.
5. You may need to make several adjustments to lower the height of the cutter grid. Tools Needed Gather the required tools and parts before starting installation. ■ Level ■ Adjustable wrench NOTE: It is easier...
Installation Instructions - Page 12
... earlier.
16. Drain cap D. To replace the water pan, set properly and that holds the water pan in on the ice scoop holder and then out.
12 Cutter grid
D. Drain pump cover
10. NOTE: On some models, remove the holder by removing the 2 screws.
Then clean the same parts with mild soap or detergent...
Dimension Guide - Page 1
...: Dimensional specifications are appropriately UL, CUL or CSA approved.
19-Mar-2019 01:02:51 EDT | RELEASED
In some European factories the letter "W" of the part code mentioned herein will be automatically replaced by the number "4000" (e.g. "W12345678" becomes "400012345678") DETAILED PLANNING DIMENSIONS 1 of recessed ice F machine to the Installation or Use & Care Guide before...
Dimension Guide - Page 2
...
Depth without door (min.)
215/8
54.91
I
Floor
2 of the part code mentioned herein will be automatically replaced by the number "4000" (e.g. All KitchenAid® appliances are appropriately UL,...KUID508H/
MODEL #
KUIO338H
in
cm
A*
Height to top of door (min.)
3347/64
85.7
B*
Height to top of handle (min.)
3115/16
81.1
C*
Height to the Installation or Use & Care Guide before ...
Dimension Guide - Page 3
...these instructions. ...VIEW
J
KUID308H/ KUID508H/
MODEL #
KUIO338H
in
cm
...part code mentioned herein will be between 30 and 120 psi (207 and 827 kPa) is required to be automatically
replaced...specifications are appropriately UL, CUL or CSA approved. distance from bottom
119/16
29.38
e
Recommended electrical connection location
w Recommended water connection location
* Install...
KitchenAid KUID508HBL Reviews
We have not received any reviews for KitchenAid yet.